Gasmate VALOR 6 User manual

1

3
Nominal Hourly Gas Consumption
Gas Type Number of
BBQ Burners
Injector Size
BBQ Burner
Injector Size
Side Burner
Total Gas Consumption
Primary Burners MJ/h
Gas
Pressure
kPa
ULPG
6 Ø .92mm Ø .98mm 75.6 2.75 kPa
MJ/h 12.6 14.4

3

5
A - 2 x axle bolts B - 2 x M8 nuts C - 4 x M6x30 bolts D - 4 x M6x15 bolts
E - 48 x M6x12 bolts F - 4 x G - 4 x M6x15 bolts
No. Description QTY
1 Lid assembly 1
2 Thermometer 1
3 Thermometer bezel 1
4 Lid handle 1
5 Warming rack 1
6 Rear lid panel 1
7 Rear lid left side panel 1
8 Rear lid right side panel 1
9 Rubber buffer 5
10 Firebox 1
11 Side shelf bracket A 1
12 Side shelf bracket B 1
13 Control panel assembly 1
14 Knob bezel 7
15 Knob 7
16 Switch 1
17 Manifold assembly 1
18 Beam 1
19 Trolley rear panel 1
20 Door stopper 1
21 Trolley front lower panel 1
No. Description QTY
22 Wheel cover panel 2
23 Bottom shelf 1
24 Right door assembly 1
25 Left door assembly 1
26 Door handle 2
27 Hot plate 2
28 Cooking grill 2
29 Flame tamer 3
30 Cross re 5
31 Burner 6
32 Burner ignition 6
33 Left side shelf 1
34 Side table panel 2
35 Side burner lid 1
36 Side burner lid axle 1
37 Side burner grill 1
38 Side burner 1
39 Side burner ignition 1
40 Side burner shelf 1
41 Side burner valve 1
42 Side burner fat cup 1
No. Description QTY
43 Drip tray handle 2
44 Drip tray 1
45 Fat cup 1
46 Hose & Regulator
Assembly
1
47 Left rear leg 1
48 Trolley left side panel 1
49 Left front leg 1
50 Left end cap 2
51 Door handle screw sleeve 4
52 Right rear leg 1
53 Trolley right side panel 1
54 Right front leg 1
55 Wheel axle 2
56 Wheel 2
57 Battery case 1
58 LED light cord 1
59 LED light 5
60 Cylinder heat shield 1
61 Side burner housing 1
62 Side burner exible hose 1
63 Cylinder belt 1

5

7
E
B
A
E

7
E
E

9
C
E E

9
E
E

11
E
E

11
D
F

13
G

13
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
STEP 18
Use a solution of soapy water (dishwashing liquid and
water is ne). Brush it on or use a spray bottle as shown in
the drawing. Ensure the connections have a good coating.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.

15

15

17
Problem Possible Reason Solution
Burner will
not ignite
Valve on cylinder is closed Open the valve on the cylinder
Control knob is closed Push in and turn the knob anti-clockwise
Electronic igniter is faulty Use a long barbecue match (see page 15)
Food is not
cooking or is
taking too long
Burner has gone out Check that the gas bottle is not empty
and re-ignite the burner
Cooking surface was not given enough time to
warm up before the food was applied
Remove the food and give the burner
time to warm the cooking surface (5-10
minutes)
There is too much food on the cooking surface Cook smaller portions
Flames on the
burners burn in
yellow or orange
ames combined
with the smell of
gas
The inlets are obstructed Check for spiders and insects or other
obstructions. Clean the burner assembly
(see page 18)
Air shutter on the burner is not adjusted correctly Adjust the air shutter correctly (see page
18)
There is a gas leak Perform a leak test (see page 13)
Flame is low while
control knob is on
high temperature
setting or burner
does not ignite
Check if the gas cylinder is empty Install a full gas cylinder and check for
leaks
Check if the gas hose is bent or kinked Straighten the gas hose
The Excess Flow device has been activated. If the
LPG cylinder valve is opened to allow gas ow
while a burner control valve is already open, the
surge of pressure will cause the device to activate
Make sure all burners are set to ‘Off’
before opening LPG cylinder. Wait 5
seconds after opening LPG valve. Light
burners one at a time
When using the
igniter function,
the burner does
not ignite
Check if gas ows out by following the manual
lighting instructions
If the burner lights up, check if the igniter
is working properly. If the burner does not
light up, clean the burner assembly (see
page 18)
Check if the electrodes and ignitor cables are
properly connected to the tube burners.
Install the electrodes properly to the tube
burners and check if all ignitor cables are
installed correctly
Check if the electrodes are covered by cooking
residue
Clean the burners as described in
cleaning and care. Additionally clean the
electrode tip with alcohol
Flame pattern
on the burners is
inhomogeneous or
does not run the
whole length of the
tube burner
Check if the burners are clean Clean the burners as described in
cleaning and care
LED light of the
knobs can’t be
switched on
Check connection and batteries Replace the 3 x D batteries if necessary.
Burner blows out
Burner isn’t installed properly Check all parts are alligned correctly
Fuel mixture Close the gap on the adjustable air
shutter
Gas supply is insufcient Straighten the gas hose and check that
the gas bottle is not empty

17

19

19