Gasmate BFR1000 User manual

• Compressor refrigerator
• Black pre-coated metal
exterior finish
• Low noise operation
• Digital thermostat control
• Durable stippled aluminium
interior finish
• Double glazed glass door/s
with lock
• Height adjustable feet
• Internal LED lights
• Supplied fully assembled
BAR FRIDGE
Model No. BFR1000, BFR2000, BFR3000
Important: Retain these instructions for future use.
04345 07/21
Gasmate® is a registered trademark of
Sitro Group Australia Pty Ltd www.gasmate.com.au
Aber Living, N.Z. www.gasmate.co.nz
118 Litres
190 Litres
307 Litres

2
PRODUCT DESCRIPTION
Inspect contents of the box to ensure all parts are included and undamaged
1. Double glazed glass door(s)
(depending on the model)
2. Adjustable digital thermostat control inside fridge
3. Adjustable shelves
(depending on the model)
4. Light switch
1
2
4
3

3
INSTALLATION & OPERATION
SAFE OPERATION
Beware of Children and Pets
Children should not be allowed to touch or operate
refrigerators or touch extension cords, if used. All
refrigerators should be kept out of reach of children,
preferably stored or locked in a secure room when not
in use.
Do Not Abuse the Power Cord
Never yank or pull on the power cord to disconnect
it from the mains supply socket. Never carry your
refrigerator by its power cord. Keep the power cord away
from heat, oil, solvents and sharp edges. Check power
cord regularly for signs of damage. If the power cord
becomes damaged have it replaced by an authorised
service facility. The supply cord should be regularly
examined for signs of damage and the appliance is not to
be used if the cord is damaged.
Extension Cords and Reels
This refrigerator is NOT designed to run off an extension
cord. If you require an additional power point please have
one installed by a qualified electrician.
The use of extension cords may cause power voltage loss
which will result in damage to the compressor this will
NOT be covered under warranty.
Electrical Installation
The electrical system of this refrigerator must be supplied
through an earthed (3 pin) circuit with a residual current
device (RCD) having a rated residual operating current not
exceeding 30 mA. If uncertain have a qualified electrician
check your electrical system before installation and/or use.
All electrical connections are to be made in a dry area.
Outdoor power points must be weatherproof and installed
by a qualified electrician.
Safety
Before attempting to operate this refrigerator, the following
basic safety precautions should be taken to reduce the risk
of fire, electric shock and personal injury. It is important
to read the instruction manual and to understand it’s
applications, limitations and potential hazards associated
with this refrigerator. This refrigerator is not intended for
use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by a
person responsible for their safety. This refrigerator is not
designed for use within 1m or above a water source. It
is important that you read, understand and follow these
instructions very carefully. They are designed for the safety
of yourself and others ensuring a long and trouble free
service life from your refrigerator. This electric refrigerator
complies with Australian and International standards and
safety requirements. Repairs should only be carried out by
qualified persons using original spare parts. Failure to do
so may result in considerable danger to the operator.
NOTE: If using the refrigerator outside in an alfresco area ensure that it is directly connected to an outdoors
power point.
Ensure this refrigerator is not left in the weather or in direct sunlight.
The electrical system of this refrigerator must be supplied through a residual current device (RCD) having
a rated residual operating current not exceeding 30 mA. If uncertain have a qualified electrician check your
electrical system before installation and/or use.
All electrical connections are to be made in a dry area.
Outdoor power points must be weatherproof and installed by a qualified electrician.
Sitro Group Australia Pty Ltd is not responsible for incorrectly located refrigerators.
FOR YOUR SAFETY

4
SPECIFIC SAFETY INSTRUCTIONS
WARNING
• Refrigerant used in this
refrigerator is flammable.
• This refrigerator should be
installed as per AS5149:2016 to
ensure that there are no sources
of ignition in any area refrigerant
could gather in the event of a leak.
• Electrical equipment should not be placed under or
near the underside of this refrigerator or anywhere
where refrigerant could gather in the event of a leak.
• Only use this refrigerator on flat and level ground.
• Before you throw away your old refrigerator, take off
the door, leave the shelves in place, so that children
may not easily climb inside.
• Never allow children to operate, play with or crawl
inside the appliance.
• This refrigerator is not designed for perishable
foods. It is a drinks refrigerator.
• Adults and children should never sit or stand on the
fridge as injury may occur.
• When you dispose of your old refrigerators and
freezers, remove any doors. Children can suffocate
if they get trapped inside.
• This appliance contains insulation formed with
flammable blowing gases. Avoid safety hazards by
carefully disposing of this appliance.
• The appliance must be plugged into its own
dedicated 220-240V, 50Hz AC electrical outlet.
• Ensure that the electric outlet is properly earthed
to ground. Consult a qualified electrician if you are
unsure.
• Do not use an extension cord or adaptor plug.
• Unplug the appliance before cleaning.
• Never unplug the appliance by pulling on the power
cord. Always grip the plug firmly, and pull straight
out of the receptacle to prevent damaging the
power cord.
• Chose a location that is not too cold - the
temperature should be above 10°C.
• Chose a location that is not affected by direct
sunlight.
• Put the appliance in a dry place, avoiding areas of
high moisture or humidity.
Do not use the refrigerator in areas where there is a
risk of explosion or fire from flammable gases. Ensure
that the area is kept clear of combustible materials.
Do not use the refrigerator in damp areas, without
suitable ventilation. This refrigerator is not designed
for use within 1m or above a water source. Do not
place within one metre (1m) of any water source.
Fire risk exists if this refrigerator is covered by or
positioned close to curtains or other combustible
materials.
• This refrigerator must be operated on an earthed
circuit (3 pins).
• This refrigerator is intended for domestic/
household use only.
• DO NOT use this refrigerator in either the
bathroom or ensuite.
• DO NOT use a 3rd party timer, or
programmable system with this refrigerator.
• DO NOT clean the refrigerator while the
refrigerator is on or plugged into the mains
power supply.
• DO NOT attempt to modify the refrigerator, power
cord, power plug or the supplied accessories in any
way.
• DO NOT expose the refrigerator to rain, water, or
use in damp wet conditions.
• DO NOT expose the refrigerator to direct sunlight.
• If left in direct sunlight the fridge may not operate
as designed.
• NEVER use with the power cord coiled, bundled up
or tied up. Always extend fully before use.
• NEVER use the refrigerator if any part of it
is damaged.
• Ensure that the refrigerator is disconnected
from the mains supply when installing, cleaning or
removing/installing.
• Always turn the refrigerator OFF at the unit switch
and the power point switch when not in use for
extended periods of time.
• Always ensure that the power cord is fully
extended.
• Always ensure that the refrigerator is kept clean and
free from dust.
• Never use refrigerator with cracked/broken glass -
replace glass before use.
RISK OF
FIRE

5
WARNING
• Don’t put the appliance in direct sunlight.
• Don’t put the appliance near stoves, fires or heaters.
• The appliance shall not be exposed to rain.
• Keep ventilation openings, in the appliance
enclosure or in the built-in structure, clear of
obstruction. Do not use mechanical devices or
other means to accelerate the defrosting process.
• Do not use electrical appliance inside the food
storage compartments of the appliance.
Protection from Moisture
Avoiding placing the refrigerator in a place where heavy
moisture is present so as to minimise possibility of rusting
of metal parts. The refrigerator should be kept out of
water or direct sprayed water, failure to do this could
cause poor performance and/or an electrical short could
occur.
Protection from Heat
The refrigerator should be protected from excessive heat
sources and out of direct sunlight.
Protect from Cold
The bar fridge should be protected from excessive
cold weather and frosts. Suggested minimum ambient
temperature should ideally be higher than 8°C, so that
optimal performance is not affected.
Moving
When fixed or moved, the refrigerator cannot be set
horizontally or reclined to more than 45° or positioned
upside down.
Never move while refrigerator is plugged in and
operating.
Once you have moved the refrigerator, leave standing in a
level position for 4 - 6 hours so that the gas can settle.
• If power cord is damaged, it must be replaced by
the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard. The
appliance is not to be used if the power cord is
damaged.
• The electrical system of this refrigerator must be
connected with an automatic 30mA circuit breaker
and/or residual current device (RCD). If uncertain
have a qualified electrician check your electrical
system before installation and/or use.
Positioning
Ensure the sides and top have at least 50mm clearance
and the rear at least 50mm clearance to ensure adequate
ventilation.
Never cover the bottom front grill as this is required for
ventilation.
After installation the appliance should be left for 24 hours
before it is plugged in and switched on this is to allow the
refrigerant to settle.
Disposal of Packaging
Always recycle and dispose of all packaging materials in
an environmentally friendly way. For specific information
on recycling in your area contact your local Council
Recycling Centre.
Disposal of Old Appliances
The majority of components are recyclable, however
there are also dangerous chemicals inside. To dispose of
old fridges first remove the doors and contact your local
council for recycling options.
Electrical Installation
The electrical system of this refrigerator must be supplied
through an earthed (3 pin) circuit with a residual current
device (RCD) having a rated residual operating current not
exceeding 30 mA. If uncertain have a qualified electrician
check your electrical system before installation and/or
use.

6
IMPORTANT
CAUTION
• Never lick icy drinks when they first come out
of the fridge. This can freeze burn your lips and
mouth.
• Never allow children to operate, play with or crawl
inside the appliance.
• If the supply cord is damaged, it must be replaced
by professional electrician. The cord must be
replaced with a cord of the same specification.
• Before you throw away your old refrigerator, take
off the door, leave the shelves in place, so that
children
may not easily climb inside.
• This refrigerator is not designed for perishable
foods. It is a drinks refrigerator.
ELECTRICAL DATA
The electrical system of this refrigerator must be supplied
through an earthed (3 pin) circuit with a residual current
device (RCD) having a rated residual operating current not
exceeding 30 mA. If uncertain have a qualified electrician
check your electrical system before installation and/or
use.
This refrigerator is fitted with a sealed electrical
connection plug that is compatible with the refrigerator,
the mains supply for Australia and meets the
requirements of international standards. This refrigerator
must be connected to a supply voltage that is equal to
that stated on the rating label. If the mains connection
plug or power cord becomes damaged it must be
replaced with a complete assembly that is identical to
the original, and this must be replaced by an authorised
service centre. The supply cord should be regularly
examined for signs of damage and the appliance is not
to be used if the cord is damaged. Always follow the
Australian requirements for connection to the mains
supply. If in doubt always consult a qualified electrician.
Note: Before using your fridge, unpack and correctly
position. Once in position leave to stand for around 24
hours before plugging in and turning on for the first time.
MAINTENANCE
• The refrigerator should be cleaned and maintained
once a month with a soft clean cloth.
• When performing maintenance, make absolutely
sure that the power plug is first disconnected from the
power outlet.
• Wipe the inner and outer surface of the
refrigerator and its accessories with soft clean wet
cloth. If they are too dirty, scrub them with neutral
detergent, and then clean them with water and
dry them with a clean cloth.
• Never use hot water, petrol, alcohol, kerosene,
abrasive powder, alkaline detergent, acid, oven
cleaners, etc. These could damage the lacquer
finish and plastics.
• If the plastic parts in refrigerator become
contaminated by oil (animal or vegetable), they
could become brittle and possibly cracked.
• Servicing of this refrigerator can only be performed
by a qualified and licensed refrigeration technician
(hydrofluorocarbon refrigerants).

7
TROUBLE SHOOTING
1. When the refrigerator does not work:
Check if there is a power failure.
Check if the power plug is plugged into the
power outlet.
Check that the R.C.D. has not been tripped.
If ambient temperature is above 30°C the Thermal
Safety Cut may have operated. Check if unit has
restarted once ambient temperature is below 25°C.
2. When the refrigerator is cooling excessively:
The temperature control dial may be set too high. If you
place drinks containing a lot of water directly under the
cool air outlets they may freeze. This does not indicate
a malfunction.
3. When the refrigerator is not cooling sufficiently:
The drinks may be packed too tightly together which
will block the flow of cool air. You may have put
something hot or a lot of drinks into the refrigerator.
The door may not have closed properly. There may
be insufficient clearance between the refrigerator and
the other surfaces, both sides, back and above. The
temperature control dial may not be set low enough.
Daily ambient temperature may be excessively high.
Check there is no direct sun on front of fridge.
4. When condensation forms on the outside of the
refrigerator:
Condensation may form on the outside when the
humidity is high. This is the same result as the
condensation formed when chilled water is poured into
a glass. It does not indicate a malfunction. Wipe dry
with a cloth.
5. When you hear a sound like water flowing:
A sound like water flowing is the refrigerant flowing.
It does not indicate a malfunction.
6. When the cabinets side panel heats up:
The side panel of the cabinet will heat up when the
door is opened and closed frequently, when starting
the unit and when the unit operates in summer with
high ambient outside temperature. Do not touch the
side panel, it is a result of heat from inside the cabinet.
It does not indicate a malfunction.
STABILISING FEET
These are already fitted to your bar fridge. Before turning
your bar fridge on please ensure your bar fridge is level
front to back and side to side.
1. If your bar fridge is not level use the fitted stabilising
feet to level.
2. To level unscrew the low corner stabilising bolt out until
bar fridge is level.
WIRE SHELVES
Remove shelves from packaging and locate on the shelf
supports and ensure they are level before use.
Stabilising Foot

8
DEFROST CYCLE
This refrigerator has an automatic defrost cycle of
approximately 20 minutes which is designed to prevent
ice build up. If you see extreme ice build up in the rear
of the refrigerator (evaporator) you can initial a manual
defrost.
When the system is in defrost indicator under the defrost
symbol will illuminate.
To Manually Activate
1. Press and hold the defrost button for 6 seconds or
until a beep is heard.
2. The light under Defrost button will be illuminated,
showing that the system is in DEFROST.
3. The DEFROST will last approximately 20 minutes
unless manually stopped.
To Manually Deactivate:
1. Press and hold the defrost button for 6 seconds or
until a beep is heard.
2. Both lights under Cooling and Defrost buttons will
be flashing.
3. These 2 flashing lights indicate that the system is
switching back to cooling.
4. The switch back to cooling can take between 5-20
minutes and when complete the light under the
cooling button will be illuminated only.
DIGITAL CONTROL
The digital display will show the internal cabinet
temperature.
Note: This may fluctuate as the refrigerator cycles on/off,
this is not a fault.
When the refrigerator is cooling mode the light under the
cooling symbol will illuminate.
When the refrigerator cycles off the light will not be
illuminated.
Setting Temperature
1. Press the SET button once, a beep will sound
and display will flash
2. Use the UP/DOWN buttons to select the
desired temperature.
3. Press the SET button again to complete or you can
leave for 5-10 seconds and it will complete and revert
back to show the internal temperature, with settings
saved.
Note: If the unit is unplugged, turned off or power is lost
you must wait 3 to 5 minutes before restarting the unit. If
you attempt to restart without waiting the refrigerator will
not start and may damage the compressor.
INTERNAL LIGHT
To turn light on press the UP button.
To turn light off press the UP button.
It is recommended that the switch be turned on
only when required.
USING YOUR REFRIGERATOR

9
GASMATE BAR FRIDGE PRODUCT RANGE - WARRANTY STATEMENT
SITRO GROUP AUSTRALIA (S.G.A.) WARRANTS
THE PURCHASER OF THIS PRODUCT AGAINST
DEFECTS IN WORKMANSHIP AND MATERIALS FOR
THE FOLLOWING PERIODS FROM THE DATE OF
PURCHASE:
For domestic use, this table applies:
Bar Fridge
Body Stainless Steel
1 Year
(surface rust excluded)
Bar Fridge
Body Powder Coated
1 Year
(surface rust excluded)
Compressor 1 Year
All Other Items 1 Year
For commercial use : 3 Months
This warranty is not transferable to a subsequent purchaser
if the product is sold by the original purchaser during the
warranty period.
If a warranty fault appears within the warranty period, S.G.A.
reserves the right to replace or repair the product.
In the event that S.G.A. chooses to replace the product, this
original warranty will expire at the original date.
If the product includes various accessories or components,
only the defective accessory or component will be replaced
or repaired.
S.G.A. reserves the right to replace defective parts of the
product with parts and components of similar quality, grade
and composition where an identical part or component is not
available.
Products presented for repair may be replaced by
refurbished products of the same type rather than being
repaired. Refurbished parts may be used to repair the
products.
To make a warranty claim, first contact S.G.A’s Customer
Service Line on the contact number below.
The purchase receipt for this product is to be retained and
must be presented if making claim under the terms of this
S.G.A. warranty.
Warranty repairs are free of charge, provided the product is
delivered to our Service Department at 33-35 Lionel Road,
Mt Waverley, Victoria, 3149 or to one of our Authorised
Service Agents.
CONTAC T DETAILS
Sitro Group Australia Pty Ltd
33-35 Lionel Road, Mt. Waverley
Victoria 3149, Australia.
Tel [phone]
Fax [phone]
[email protected]
If a warranty fault is found the freight cost will be credited to
the owner. If no fault is found the product will be returned
and any costs associated with the service will be charged to
the owner.
Products sent freight forward will not be accepted. In most
cases the defective accessory or component only will need
to be returned. The product or part of the product being
returned must be adequately protected in a box.
S.G.A. will not be responsible for any in-transit loss or
damage.
This warranty does not apply to any defect, deterioration,
loss, injury or damage occasioned by or as a result of misuse
or abuse, negligent handling or storage, normal wear and
tear or if the product has not been installed and used in
accordance with S.G.A.’s instructions, recommendations
and specifications or if the product has been subjected
to abnormal conditions. The warranty does not apply to
blockages caused by insects or living organisms.
The warranty is void if there is evidence of the product being
tampered with by unauthorised persons.
The warranty does not extend to installation or disconnection
costs.
Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. The benefits of this
warranty are in addition to any rights and remedies imposed
by Australian State and Federal legislation that cannot be
excluded.
Electric Products Approved For Outdoor Use Only
For warranty claims, service, spare parts or products
information in Australia, please call SITRO GROUP
AUSTRALIA Pty Ltd on the Customer Service Line 1300
174 876
Register your Warranty online at
www.gasmate.com.au
A receipt or proof of purchase is required and must be kept
for your records.
Note: If you do not have internet access call our customer
service team on 1300 174 876

Model BFR1000 BFR2000 BFR3000
Doors 123
Gross Capacity 118L 190L 307L
Rated Voltage 220~240V AC 220~240V AC 220~240V AC
Rated Frequency 50Hz 50Hz 50Hz
Rated Current 1.2A 1.5A 2.1A
Rated Input Power at 240V AC 180W 213W 408W
Energy Consumption 1.27 kw.h/24h 2.29 kw.h/24h 3.5 kw.h/24h
IP Rating IP24 IP24 IP24
Light Type LED 12V <10W LED 12V <10W LED 12V <10W
Refrigerant R600a R600a R600a
Refrigerant Charge Volume 55gm 68gm 75gm
Foam Blowing Agent Cyclopentane Cyclopentane Cyclopentane
Nett Weight 34kg 50kg 75kg
Noise Level 45db(A) 45db(A) 45db(A)
Specifications are subject to change without prior notice.
If the technical specifications are different from the plate on the back of the refrigerator,
please refer to the plate.
TECHNICAL SPECIFICATIONS
For any queries or assistance call
Customer Service
(Australia Only)
1300 174 876
Hours of operation:
Monday to Friday 8am - 5pm EST
Do not return to place of purchase.
Keep your purchase receipt, this will be required to
make any claims under the 1 year warranty.