Gason Eureka Jindara Spectre User manual
(Part No. 233885)
Installation Instructions
Read and follow these instructions (in conjunction with the Jewel / Spectre
Freestanding manual) carefully before installing this appliance.
SAVE THESE INSTRUCTIONS
Sheet 1 of 6 GPN 234969
F:\Docs\Manuals\Heaters\Heaters\GPN 234969 Jewel Spectre Thru Wall
Minimum requirements
This Heater has been tested to AS2918:2001 Appendix B.
Test Report No. ASFT18004 - 1
kit. For the through wall installation additional
8˝ stainless is to be over the 7˝ stainless active
then a 9˝ mesh shield and a 10˝ stainless steel
shield are to be installed, both to ceiling height.
(See diagram opposite)
9˝ solid back
mesh
8˝ stainless
7˝ stainless
!
10˝ stainless steel
shield up to
drop box height
NB: First height 4600 mm (+/– 300mm) from protector
Internal wall
120mm
min.
These must be used to make the installation conform.
Jewel / Spectre Through Wall Kit
• The installation of this appliance must be carried out as per the manual and the ue manufactuer’s specications
We recommend that you use a qualified installer to carry out the installation.
• Default clearance values and flue requirements specified in AS/NZS 2918-2001 must be used for any clearance values not
given in these instructions.
• If in doubt, do not hesitate to contact your local Jindara or Eureka dealer.
• This appliance weighs in excess of 230 kilograms. Extreme care should be taken when handling the appliance.
• This thru-wall kit is designed for use with plasterboard stud walls,
with a total thickness ranging between 90mm and 110mm.
• Note that the wall section below the appliance fascia on the insert
side is filled, as per figure 1. It should be supported by a stud with a
10mm x 35mm horizontal cut-out, as per figure 2. This is to allow
the base of the freestanding unit to protrude far enough through
the wall.
Hole cutting dimensions & clearances to combustibles
0$7(5,$/0DWHULDOQRWVSHFLILHG!
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
Figure 1
See
Notes 1 & 2
See
Note 3
890 mm
860 mm714mm
Note 1: If present, a combustible mantle shelf must be positioned
a minimum of 500mm above the apliance hot air outlet.
Note 2: Combustible internal wall framing must not be installed
less than 475mm above the appliance top plate.
Note 3: Non-combustible internal wall framing must be used if
installed directly above the appliance, less than 475mm
from the top plate.
0$7(5,$/0DWHULDOQRWVSHFLILHG!
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
Insert
side
35 mm
15 mm
Floor protection
minimum thickness
6 mm
45 mm
110 mm
Freestanding
side
Horizontal lower
support stud
• A minimum 1590mm x 940mm floor protector with a minimum
thickness of 6mm must be installed under the appliance, as per
figure 3.
• The floor protector must extend a minimum of 420mm from each
appliance door and 155mm from the pedestal base on either side
of the appliance.
Figure 2
0$7(5,$/0DWHULDOQRWVSHFLILHG!
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
Internal wall
Figure 3
420mm 420mm
940mm
1590mm
372mm
using an Australian Standard
,7(0 3$571R
'(6&5,37,21
'HIDXOW
47<
6,=(
%5$&.(77+58:$//.,7
$
3$1(/,1),//)$6&,$
$
6&5(:7(.[6(/)7
:$6+(5)/$766[[
)$6&,$7+58:$//
$
+($76+,(/'7+528*+:$//
$
+($76+,(/'7+528*+:$//
$
+($76+,(/'7+528*+:$//
$
+($76+,(/'7+528*+:$//
$
),//3$1(/5+
$
),//3$1(//+
$
635,1*(;7PP[PP
&20%867,%/(:$//3$1(/
)5217
%
)$6&,$3$1(/-(:(/63(&75(
$
&20%867,%/(:$//),//3$1(/
)6
$
,1),//02817%5$&.(7
$
6&5(:67$3[*3+
6&5(:6(70[[3+7+(;
=3
1871</2&0
6&5(:&$30[%87+'
:$6+(5)/$70;=3
.12%32:(56:,7&+
$
6:,7&+326,7,2163'721
21
)$16:,7&+63(('527$5<
%/$1.,1*3$1(/,1%
$
187:+,=/2&.)/$1*(066
3$,17&$10(7%/$&.
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
-(:(/63(&75()6
7+58:$//.,7&20%867,%/(:$//
77
(1*35
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
77
Parts
1
2
3
4
5
6
7
8
9
Fill Panel Mount
Fill Panel
Tek Screw 10-16 x 16mm
Washer Flat 8 x 20
Insert Fascia Panel
Inner Heat Shield A
Outer Heat Shield A
Inner Heat Shield B
Outer Heat Shield B
Ref. Description Qty.
2
1
6
4
1
1
1
1
1
10
11
12
13
14
15
16
17
18
Side Fill Panel R/H
Side Fill Panel L/H
Retaining Spring
Front Heat Shield Panel
F/S Fascia Panel
Rear Heat Shield Panel
Side Fill Mount Bracket
S/Tap Screw 1/2” x 10
Set Screw M6 x 20
Ref. Description Qty.
1
1
4
1
1
1
4
32
4
Ref. Description Qty.
Nut Nyloc M6
Cap Screw M8 x 20
Washer Flat M6
Switch Knob
Switch - 2 Position
Switch - 3 Position
Blanking Panel
Nut Whiz Lock M6
Paint - Metallic Black
4
4
8
1
1
1
1
2
1
19
20
21
22
23
24
25
26
27
Sheet 2 of 6 GPN 234969
Step 1
• Ensure that the power lead of the appliance is disconnected.
• Remove the door from the appliance, at the end being installed through the wall.
• Note that if fan controls are intended to be installed on the thru-wall face if the installation, the door at the end of the appliance with fan
controls in the pedestal base should be selected for this step. Refer to figure 5.
Figure 4
$
$
6(&7,21$$
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
-(:(/63(&75()6
7+58:$//.,7&20%867,%/(:$//
77
(1*35
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
77
Sheet 3 of 6 GPN 234969
Step 2
• Remove the pedestal ll panel from the base of the appliance, at the
end being installed through the wall.
• Disconnect fan harness connectors from the switches housed in the
fill panel and secure the earth wire eyelets to the pedestal base, at
the point shown in figure 5.
Step 3
• Assemble the heatshield components as shown in gure 6, ensuring all plastic
wraping is removed from the stainless steel before assembly. Note that inner
and outer heat shield A components attach to heat shield front panel, inner and
outer heat shield B components are attached to A components using screws, with
slots used for adjustment of overall depth.
• Ensure all retaining screws are securely fastened and that the depth of the heat
shields is uniformly adjusted.
• Depth of the heat shields (x) is determined using the following calculation:
x = wall thickness - 5mm
Step 4
• Install the front heatshield assembly to the far side of the installation,
as shown in gure 7.
• Measuring vertically from the surface that the heater is sitting on, the bottom edge
of the heatshield assembly should be raised by 77mm.
• Secure mounting brackets in place using wood screws, attaching to the vertical
stud on both sides of the cut-out.
Step 5
• Install the rear heatshield panel, securing in place with 4x retaining springs,
as shown in gure 8.
'
'(7$,/'
6&$/(
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
'
'(7$,/'
6&$/(
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
$
$
6(&7,21$$
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
-(:(/63(&75()6
7+58:$//.,7&20%867,%/(:$//
77
(1*35
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
77
Attach earth points
firmly using screw
Heat Shield
Front Panel
x
Inner Heat
Shield A
Inner Heat
Shield B
Outer Heat
Shield B
Outer Heat
Shield A
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
-(:(/63(&75()6
7+58:$//.,7&20%867,%/(:$//
77
(1*35
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
77
77mm - bottom edge of fascia
to top face of floor protector.
Secure to vertical stud
through brackets
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
-(:(/63(&75()6
7+58:$//.,7&20%867,%/(:$//
77
(1*35
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
77
(Through wall side)
(Freestanding side)
Figure 5
Figure 6
Figure 7
Figure 8
Retaining spring
Sheet 4 of 6 GPN 234969
Step 6
• Using the wall thickness measurement, determine value (y) using
the following equation:
y = wall thickness - 88mm, (± 2mm)
• Referring to figure 9, measure distance y from the front of the
pedestal base at the side pointed towards the wall. Mark and drill
a 6.5mm hole at this point, 43mm above the pedestal base on both
sides of the appliance.
Step 7
• Move heater into position, central to the wall cut-out and heat
shield assembly, as per figure 10.
• Position the appliance so that the distance from the pedestal base
to the heat shield panel on the freestanding side is 575mm.
Step 8
• Install the rear fascia panel as shown in gure 11. Press the
locating tabs of the panel through the cut-out sections in
the heat shield panel, then secure by pushing the fascia
down until it is seated in position.
Step 9
• Using the suppied M6 fasteners, secure the
rear fascia ll panels and mount brackets in
position, as per gures 12 & 13.
• This is best carried out by rst installing the
brackets, then securing the ll panels in place.
Figure 9
'
'(7$,/'
6&$/(
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
y
43mm
Ø 6.5mm
Facing towards
wall
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
Figure 10
575mm
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
Figure 11
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
-(:(/63(&75()6
7+58:$//.,7&20%867,%/(:$//
77
(1*35
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
77
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
Component assembly.
Refer to page 2 for component identification.
Figure 12 Figure 13
Sheet 5 of 6 GPN 234969
Step 11
• Connect the fan control switches (already tted to the ll panel), ensuring connections
are made as per the diagram in appendix A. Ensure that all wiring is secured and unable
to be caught in fans or be crushed/rubbed through on heater panels.
• Note: If the fan controls have been left in the pedestal base on the freestanding
side of the installation, remove the switches fitted to the fill panel and fit the
blanking panel as per figure 14.
Step 12
• Secure the ll panel to the panel mount brackets.
• The easiest way to do this is to drive the tek-screws into the
panel mount brackets until they are around 4mm from fully
seated. Press the ll panel over the heads of the screws and
push down, locating the screws in the cut-out slots. Tighten
the tek-screws the rest of the way using a spanner.
Refer to gure 16.
Step 13
• Fit the front fascia using 4x M8 button head bolts and washers, re-tting the door rider
plate over the fascia at the top right corner, as per gure 17. Ensure that the fascia sits
squarely and centrally on the appliance.
• Note: If the front fascia is protruding excessively from the wall, the heater should be
shifted backwards to take up this gap. Do not attempt to adjust the fascia position by
bending or shimming the fascia panel at its mounting points - This will likely interfere
with door operation. The fascia on the freestanding side should be checked to ensure
it is still sitting correctly after any adjustments are made.
Step 14
• Re-t the door to the appliance, ensuring that it opens and closes correctly. If the door does
not latch correctly, refer to the user manual supplied with the appliance for door adjustment
procedures. If required, use the spray can supplied to touch up the paint on the thru-wall kit
and `the appliance, following the directions on the spray can.
Figure 14
'
'(7$,/'
6&$/(
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
Figure 15
Figure 16
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
-(:(/63(&75()6
7+58:$//.,7&20%867,%/(:$//
77
(1*35
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
77
Figure 18
Step 10
• Fit the ll panel mounts using tek-screws supplied, as per gure 14.
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
-(:(/63(&75()6
7+58:$//.,7&20%867,%/(:$//
77
(1*35
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
77
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
Locate fill panel at these points
then tighten retaining screws
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
Component assembly.
Refer to page 2 for component identification.
Figure 17
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%<
(&11R
'$7(
5(9
%<
(&11R
'$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
Phone (03) 9729 1422
Fax (03) 9729 1455
Sheet 4 of 6 GPN 234969
Gason Heating reserves the right to modify or alter specications, materials, etc in the interests of product improvement.
Any enquiries contact the dealer from whom you purchased your heater.
PLEASE COMPLETE:
Dealer name:
Dealer Address:
Phone Number:
Please attach your original purchase dockets to this instruction book for future reference.
F:\Docs\Manuals\Heaters\Heaters\GPN 234969 Jewel Spectre Thru Wall
Heating
This manual suits for next models
1
Table of contents
Other Gason Fireplace Accessories manuals
Popular Fireplace Accessories manuals by other brands
Dimplex
Dimplex GBF1500-GLASS Assembly instructions
Empire Comfort Systems
Empire Comfort Systems OLX24WR-1 Installation instructions and owner's manual
pleasant hearth
pleasant hearth WS104L instructions
New Buck Corporation
New Buck Corporation 42ZCBB user guide
IHP
IHP DWLS-RNCL35 installation instructions
Dimplex
Dimplex DFP6745 install guide
Empire Comfort Systems
Empire Comfort Systems DFF30RBL installation instructions
American Hearth
American Hearth SAVANNAH ALS-18F2-1 Installation instructions and owner's manual
Town & Country Fireplaces
Town & Country Fireplaces TC30 Black Diamond instructions
IHP
IHP EPIC-TRIM-B installation instructions
Valor
Valor Legend G3 739NGK installation instructions
HPC
HPC MLFPK Series Installation & operation instructions
EmberGlow
EmberGlow RVS304 Supplemental installation instructions
Lopi
Lopi 21 DV Wilmington Face user manual
Lennox Hearth Products
Lennox Hearth Products Stainless Steel Outdoor Weather Cover... installation instructions
Valor
Valor President ZC Cast Front 536CXB Installation guides
pleasant hearth
pleasant hearth LS938-96SC manual
pleasant hearth
pleasant hearth FA011TL manual