Gason Eureka Jindara Duet User manual

Phone [phone]
Fax [phone]
Sheet 4 of 4 GPN 215238
Gason Heating reserves the right to modify or alter specifications, materials, etc in the interests of product improvement.
Any enquiries contact the dealer from whom you purchased your heater.
PLEASE COMPLETE:
Dealer name:
Dealer Address:
Phone Number:
Please attach your original purchase dockets to this instruction book for future reference.
F:\Docs\Manuals\Heaters\HM215238\Duet In Wall Inst
(through Windows NT Explorer)
Heating

Hole construction dimensions
Duet/Duplicity Masonry Wall Kit
(Part No. 215238)
Installation Instructions
WARNING
1015mm
1015mm
Hearth
120mm
220mm
mm005mm005
400mm
1800mm
1040mm
• The installation of this appliance must be carried out as per this manual and the ue manufacturer’s specications.
We recommend that you use a qualied installer to carry out the installation.
• If you have any other enquiries, please contact the dealer from whom you purchased your heater.
• This appliance weighs in excess of 230 kilograms. Extreme care should be taken when handling the appliance.
For installation through masonry walls only.
Read and follow these instructions (in conjunction with the Duet/Duplicity
Freestanding manual) carefully before installing this appliance.
SAVE THESE INSTRUCTIONS
Clearances to combustibles
The Duet/Duplicity through wall has been tested to the Australian Standard
2918:2001 Appendix B. Test Report No. HCMG/03/009. For this installation
the ue kit could vary and should be installed to AS/NZS 2918:2001.
The Duet/Duplicity through wall heater conforms to the Australia Standard
in the following placement of the appliance in relation to combustible
surfaces:
A minimum 1040mm
wide x 1800mm deep x
12mm thick oor
protector should be used
under and in front of the
appliance when installing.
The oor protector should
extend 500mm in front of
the appliance base on
both doors.
When constructing the
masonry wall ensure width
is within 645mm minimum
to 680mm maximum in
thickness.
Sheet 1 of 4 GPN 215238
F:\Docs\Manuals\Heaters\HM215238\Duet Masonry Inst
(through Windows NT Explorer)
1015mm
(cutout)
1015mm
(cutout)
Max 680mm
Min 645mm
Ensure ue
spigot is
centred
1040mm
1040mm
Masonry Wall
Heating

Step 2
1. Slide one fascia assembly (Part 1) over the front of the
heater, so that pre-drilled screw holes (A) and (B) are aligned.
(NOTE: These holes allow for a 680mm wall thickness.)
2. Insert screw (supplied) and tighten.
3. Do this on each side of the heater.
NOTE: If the wall thickness is between 680mm and 645mm, you
will need to drill a new 3mm dia. hole (A). Position it so that the
flue spigot will be centred within the wall cavity. e.g if the wall
thickness is 650mm, the hole should be drilled 217mm from the
centre of the spigot
(B) (A)
1/2 wall thickness
(minus 108mm)
Step 1
1. Remove screws from the heater pedestal fascia panels
2. Position lower fascia panels (Parts 2 & 3) as shown (one on
each side and end of heater)
3. Reattach screws for both pedestal fascia panels.
Pedestal fascia panel
goes on top of the
lower fascia panels
Lower
fascia panel
Lower
fascia panel
Panels should be flush
with side of base
1. Fascia Assembly - qty 2
2. Panel fascia - lower left hand - qty 2
3. Panel fascia - lower right hand - qty 2
4. Spray can
5. 8G self tapping screws - qty 22
6. Fascia retaining strips - qty 2
7. 3mm dia. drill
8. 5mm dia. drill
Parts
11
23
4
5
6
Sheet 2 of 4 GPN 215238
F:\Docs\Manuals\Heaters\HM215238\Duet In Wall Inst
(through Windows NT Explorer)
Centre of spigot
Heater to be assembled from steps 1 to 4 before placing into masonry fireplace.

Step 3
1. Use a square to ensure the fascia assembly is
perfectly vertical.
2. Using a 3mm dia drill bit (supplied), drill holes (C)
and (D) through the fascia assembly and into the side
of the heater. Insert screws (Part 5) and tighten.
3. Do this on the other side of the heater as well.
Step 6
1. Attach the fascia assembly removed in Step 4 with
screws tightened from the outside of the heater, on
both sides of the fascia assembly.
(C)
(D)
Square
Step 5
Position heater into masonry opening. Ensure it is centrally
located and the fascia assembly is hard up against wall.
Step 4
1. Attach the other fascia assembly as per steps 2 and 3.
2. Position fascia retaining Strip (Part 6) by placing it along the
edge of the Fascia Assembly (See detail). Ensure strip is flush
with bottom of heater.
3. Using a 3mm dia drill bit, drill 4 holes through the fascia
retaining strip and attach to the side of the heater.
4. Using a 3mm dia drill bit, drill through the other 4 holes in
the retaining strip into the fascia assembly.
5. Remove fascia retaining strip from heater and fascia
assembly
6. Remove the fascia assembly, and then re-drill the holes in the
fascia assembly to 5mm dia using drill bit supplied.
7. Repeat for the other side of heater.
8. Screw fascia retaining strip back into position on both sides
of heater
Sheet 3 of 4 GPN 215238
F:\Docs\Manuals\Heaters\HM215238\Duet In Wall Inst
(through Windows NT Explorer)
Drill holes
Drill holes
Drill
holes
Fascia Assembly
Fascia Retaining Strip
Ensure flush at bottom
Insert screws
(4 each side)
Step 7
1. If required use spray can (Part 4) to touch up if required. Follow
directions on spray can.