FireplaceXtrordinair 4237 User manual

4237
Fireback Installation
96100873 Brick, 96100874 Herringbone, 96100875 Enamel Black,
96100877 Stacked Tan Brick
Page 1 of 4 17601933 - 7/30/21 Travis Industries, Inc.
Compatibility
 4237 Fireplace (FIREBACKS ARE REQUIRED BEFORE OPERATING THE 4237 FIREPLACE)
Packing List
 Rear Fireback (ceramic firebacks have 2 pieces - note orientation below)
NOTE: The rear fireback of the Herringbone and the Stacked Tan kits have an arrow cast into the back. To
ensure proper brick alignment make sure the arrow is pointing upward. The rear panel of the Handmade Brick
liner can be installed with either edge facing up.
 Left and Right Side Fireback (note orientation below)
Handmade Brick Handmade Herringbone Stacked Tan Brick
 Left, Right, and Front Floor Fireback
Handmade Brick, Herringbone and Stacked Tan Brick are shown below (note orientation).
Black Enamel is slightly different (see page 4)
Each side
fireback has a
small notch at
the front of the
upper edge

4237
Fireback Installation
96100873 Brick, 96100874 Herringbone, 96100875 Enamel Black,
96100877 Stacked Tan Brick
Page 2 of 4 17601933 - 7/30/21 Travis Industries, Inc.
Installation
WARNING Turn off gas to the appliance and make sure it is cool prior to conducting service.
1 The firebacks should be installed while
finalizing the installation (before installing
the logs). Remove the glass frame.
Remove the grate and place it aside (2
screws hold it in place - see the installation
manual for details).
2 Remove the 8 fireback clips inside the
firebox. These clips have keyhole slots that
allow them to be removed without removing
the screws (see illustration below).
Enamel Black Firebacks Only
Remove the rear log shelf (4 screws hold it in place). After the rear firebacks are in place, replace the log
shelf.

4237
Fireback Installation
96100873 Brick, 96100874 Herringbone, 96100875 Enamel Black,
96100877 Stacked Tan Brick
Page 3 of 4 17601933 - 7/30/21 Travis Industries, Inc.
4237 EG units with Enamel Black Firebacks ONLY
Remove the rear log shelf. Loosen the 2 screws that secure the shelf to the unit, slide the shelf backward slightly
and lift up to remove. After the rear fireback is in place, replace the log shelf.
3 Ceramic Firebacks:
Place the lower rear fireback in place.
While holding it in place, place the
upper, rear fireback on top of it
(continue to hold both in place).
Enamel Black Firebacks:
Place the rear fireback in place.
All Firebacks:
Replace the side fireback clips,
followed by the upper fireback clips to
secure the rear fireback(s).

4237
Fireback Installation
96100873 Brick, 96100874 Herringbone, 96100875 Enamel Black,
96100877 Stacked Tan Brick
Page 4 of 4 17601933 - 8/10/21 Travis Industries, Inc.
Installation (continued)
4 Place one side fireback in place.
Secure with the two fireback clips.
Repeat these steps for the remaining
side fireback.
5 Place the floor firebacks in
place.
4237 EG UNITS
Discard the floor fireback
6 Replace the grate, making
sure the grate inserts into the
two square holes on the floor
fireback. Secure it using the
screws removed earlier.
7 Restore the fireplace to the
correct configuration (see
manual for details).
CLEANING ENAMEL FIREBACKS
We recommend cleaning the enamel surface with glass cleaner and a soft cloth.