GCX AG-0021-100 User manual

DU-AG-0021-100 Rev A 4/15/08 GCX Corp. Page 1 of 6
Installation Guide
Top Shelf Mounting Kit for Mounting Philips Intellivue MP20/30/40/50/60/70
On Dräger Fabius GS Anesthesia Machine
The purpose of this guide is to describe installation of mounting assemblies on the anesthesia machine.
WARNING: USE OF MOUNTING HARDWARE AND MONITORING COMPONENTS OTHER THAN
THOSE DESCRIBED IN THIS DOCUMENT MAY RESULT IN SERIOUS INJURY DUE TO TIPPING OF
THE ANESTHESIA MACHINE.
WARNING: ALL DEVICES AND MOUNTING EQUIPMENT SHOULD BE POSITIONED INWARD, CLOSE
TO THE ANESTHESIA MACHINE, DURING TRANSPORT.
Installer: When installation is completed, provide these instructions and all related documentation to the end
user for future reference.
Mounts for MP20/30/40/50/60/70
Horizontal Mount for G5
(page 5)
Low Profile Column for Monitor
(pages 3 - 4)
Top Plate/Channel
(pages 2 - 3)

DU-AG-0021-100 Rev A 4/15/08 GCX Corp. Page 2 of 6
Attaching Top Plate/Channel to Top of Fabius GS
The following parts and hardware are included in this installation kit (hardware not shown):
Tools Required
• Drill (not provided)
• 1/4'' drill bit (not provided)
• Phillips screwdriver
1. Locate four (4) dimples in top of anesthesia machine. Dimples indicate locations of threaded inserts beneath top
surface. If dimples are difficult to locate, use Top Plate/Channel assembly as a template and mark top of machine
through four (4) mounting holes.
2. Using a 1/4'' drill bit, drill in locations marked in step 1 (drill only where dimples are present). CAUTION: Do not allow
drill bit to penetrate more than 1/4'' into top of machine. Drilling too deeply may damage threaded inserts and internal
components of the machine. Remove all drilling chips.
3. Align four (4) mounting holes in Top Plate with corresponding holes in top of machine (drilled in step 2). Fasten Top
Plate to machine with four (4) M5 x 30mm Pan Head Machine Screws (PHMS)
Item # Description Qty
1 Top Plate with 21'' Channel 1
2 M5 x 30 mm Pan Head Machine Screw (PHMS) 4
3 Label, Tip Hazard 1
Top Plate/Channel
M5 x 30mm PHMS (4)
Locations of Threaded Inserts (4)
in top of Fabius GS
1

DU-AG-0021-100 Rev A 4/15/08 GCX Corp. Page 3 of 6
4. Attach Tip Caution Label to front center of top shelf bezel as shown below.
Mounting Low Profile Mount in Channel
The following parts and hardware are included in this installation kit (hardware not shown):
Tools Required
• Phillips screwdriver
1. Slide the Base Plate into the channel and move to desired mounting position.
2. Tighten two (2) thumb screws to secure position in channel.
Installation Note: Do not attach the Table Top Mount to the Arm/Mounting
Adapter if you will be mounting an MP20/30 monitor equipped with the mounting
interface shown in photo (right). See "Mounting the Monitor on the Arm" (page 6)
for instructions specific to this type of mounting plate.
Item # Description Qty
1 Low Profile Column with Channel Mount 1
2 M6 x 8mm Flat Head Machine Screw (FHMS) 2
3 M6 x 12mm FHMS 1
*4 Spacer, MP20/30 1
*5 M6 x 16mm PHMS 2
*See "MP20/30 non-Table Top Mount" on page 6 for use of these parts.
Do Not Attach Table Top Mount if MP20/30
Monitor is Equipped with This Mounting Interface
Thumb Screws (2)
1
4

DU-AG-0021-100 Rev A 4/15/08 GCX Corp. Page 4 of 6
3. Fasten Table Top Mount to Mounting Adapter with one (1) M6 x 12mm FHMS and two (2) M6 x 8mm FHMS as shown
MP20/30 non-Table Top Mount
1. Fit Spacer into recessed area on top of Mounting Adapter (below). Ensure Spacer remains between Mounting Adapter
and monitor.
2. Insert two (2) M6 x 16mm PHMS through bottom of Mounting Adapter and thread into mounting holes in bottom of
monitor.
M6 x 12 mm FHMS (1)
M6 x 8 mm FHMS (2)
Mounting Adapte
r
Table Top Mount
(Supplied by Philips)
Spacer
Spacer
Mounting Adapter
M6 x 16 mm PHMS (2)

DU-AG-0021-100 Rev A 4/15/08 GCX Corp. Page 5 of 6
Swiveling the Mounted Instrument
Grasp the sides of the instrument and swivel to desired position. Note: Swivel is limited to ± 20º on this Mount.
Adjusting Tilt and Tilt Tension
Tilt: Grasp the top and bottom of the instrument and tilt it to desired angle.
Tilt Tension: Using the 5/32'' hex wrench provided, equally tighten or
loosen the two (2) Tilt Tension Screws.
Mounting Horizontal Mount in Channel
The following parts and hardware are included in this installation kit (hardware not shown):
Tools Required
• Phillips screwdriver
1. Fasten the Philips-supplied Table Top Mount to the Mounting Adapter with three (3) M6 x 10mm PHMS as shown below.
2. With two (2) set screws oriented toward rear of application, slide Horizontal Mount into Channel and move Mount to
desired instrument-mounting position (example below left).
3. Tighten two (2) Phillips-head set screws at rear of Horizontal Mount to prevent movement of Mount (below right). See
page 5 for photo of Horizontal Channel Mount installed on top of Fabius GS.
Item # Description Qty
1 Horizontal Channel Mount 1
2 M6 x 10mm Flat Head Machine Screw (FHMS) 3
Table Top Mount
(Supplied by Philips)
M6 X 10mm FHMS (3)
Horizontal Mount Adapte
r
Set Screws
(Rear of Mount)
Insert Horizontal Mount
In Channel
1
Tilt Tension Screws (2)

DU-AG-0021-100 Rev A 4/15/08 GCX Corp. Page 6 of 6
Periodic Maintenance
All fasteners associated with the mounting system should be inspected periodically and tightened or adjusted as
necessary for optimal operation and safety.
Cleaning the Mounting Assembly
CAUTION: GCX makes no claims regarding the efficacy of the listed chemicals or processes as a means for controlling
infection. Consult your hospital’s infection control officer or epidemiologist. To clean or sterilize mounted devices or
accessory equipment, refer to the specific instructions delivered with those products.
1. The mounting assembly may be cleaned with most mild, non-abrasive solutions commonly used in the hospital
environment (e.g. diluted bleach, ammonia, or alcohol solutions).
2. The surface finish will be permanently damaged by strong chemicals and solvents such as acetone or
trichloroethylene.
3. Steel wool or other abrasive material should never be used.
4. Damage caused by the use of unapproved substances or processes will not be warranted. We recommend testing of
any cleaning solution on a small area of the arm that is not visible to verify compatibility.
5. Never submerge or allow liquids to enter the arm. Wipe any cleaning agents off the arm immediately using a water-
dampened cloth. Dry mounting assembly thoroughly after cleaning.