GCX FLP-0008-53 User manual

DU-FLP-0008-53Rev C 03/28/16 GCX Corp Page 1 of 6
InstallationGuide
FoldingL-Bracketfor Flat Panel/KeyboardApplicationswith Multi-PositionWork Surface
(Refertoqualifiedpersonnel)
MAX. LOAD:When mounted on VHM Variable Height Arm maximum load shall be kept below
25lbs/11.3kg–The VHM used must be load rated for a minimum of 40lbs/18.1kg.
WARNING: The combination of a support arm and the L-Bracket presents a potential pinch
hazard at all points and positions where the support arm and L-Bracket can come into contact.
CAUTION: Do not place fingers or cables in-between the Folding Keyboard Bracket Mounting
Block and the Mounting Plate surfaces. There is risk of pinching or crushing fingers and cables,
especiallywhile installing the keyboard tray and adjusting the folding tension.
Purpose:
1. Describe attachment of L-bracket to Arm (page 2).
2. Describe attachment of Keyboard tray with Multi-PositionWork Surface (page3)
3. Describe attachment of Display Mounting Bracket to Display (page 3).
4. Describe adjustment of display height (page 4).
5. Describe adjustment of display tilt tension (page 4).
6. Describe folding tension adjustment(page 4).
7. Describe operation of Multi Position Work Surface (page 5).
8. Describe Storage Bin attachment (page 6).
23875 Cypress Drive Petaluma, CA94954 800.228.2555707.773.1100Fax [phone] www.gcx.com

DU-FLP-0008-53Rev C 03/28/16 GCX Corp Page 2 of 6
1
B
Parts Reference
The following parts and hardware are included in this installation kit:
Item #
Description
Qty
1
Folding L-BracketAssembly with Flat Panel Mount
1
2
Keyboardtray with Multi-PositionWorkSurface
1
3
StorageBin
1
4
1/4-28x 3/4” Flat HeadSocket Cap Machine Screws (FHSCS)
2
5
10-32 x 5/16” Flat Head Machine Screw (FHMS)
4
6
FLP-0002-1775-100mmVESA Adapter(not shown)
1
Tools Required:
• 5/32” hex wrench (provided)
• Phillips screwdriver (not provided)
Attaching the L-Bracket to an M Series Pivot or VHM Variable Height Arm
1. Install upper screw with a few turns. Install L-bracket onto upper screw, and locate into top of key hole of bracket.
2. Install lower screw then using a 5/32” Hex Wrench, fasten the two (2) 1/4-28 x 3/4” FHSCS.
(VHM Arm shown below)
3. Use blank label provided to cover screws –Clean surface before applying the label.
Blank Label
3
1
2
1/4-28x¾” FHSCS
3
5
4
2

DU-FLP-0008-53Rev C 03/28/16 GCX Corp Page 3 of 6
Attaching Key Board Tray to L- Bracket
1. Slide Key Board Tray into L-Bracket’s Hinge.
2. Open lid on Key Board Tray and align holes, install (4) 10-32 x 5/16” FHMS using a phillips screwdriver (not provided)
Attaching Flat Panel Display
Installation Note: To mount a display with 100 x 100mm pattern use VESA mounting adapter (included) install per
separatelyprinted instructions.
1. Thread two (2) M4 x 10mm PHMS into the top two (2) threaded holes of the 75 x 75mm mounting pattern, leaving
4mm of thread exposed (approximately6 full turns from tight).
2. Position the display onto the VESA Mounting Plate by guiding the screws into the slots in the top of the Mounting
Plate (below left). Thread two (2) M4 x 10mm PHMS screws into the lower mounting holes (below right). Tighten all
screws.
1
2
1
2
10-32 X 5/16”

DU-FLP-0008-53Rev C 03/28/16 GCX Corp Page 4 of 6
Adjusting the Display height
1. To change primary height adjustment tension, remove
protective cap to expose Lock Nut. Use a ½” (13mm)
socket wrench to tighten or loosen the Lock Nut to
adjust fit in L-Bracket. Place the protective cap on the
Lock Nut once adjustment is completed.
2. To change secondary height adjustment, hold Display,
loosen Height AdjustmentKnob, move Display to
desired vertical position and tighten Height Adjustment
Knob.
Adjusting DisplayTilt Tension
1. To adjust tilt tension on the Display Mount, equally
loosen or tighten the two (2) Tension Adjustment Screws
with 5/32” HexWrench until desired tension is achieved.
Adjusting Folding Tension on the Keyboard Bracket
Tilt Tension Screws (2)
If the Folding Keyboard Bracket becomes difficult to fold or will not maintain the folded (upward) position, adjust folding
tension as described below:
1. Pry Plastic bolt covers off each end of the Tension Bolt. Replace bolt covers after adjustment. Using a 1/2" [13mm]
wrench on each end of the bolt, tighten or loosen bolt until desired tension is achieved.
1
FoldingTensionBolt Plastic Bolt Covers (2) Folding TensionBolt

DU-FLP-0008-53Rev C 03/28/16 GCX Corp Page 5 of 6
Operation of the Multi-Position Work-Surface
The work-surfacecan be positioned: over the keyboard, in “music stand” position for documents, or all the way to the back
and flat for general tasks. To adjust, grab both sides and move to desired position.
To fold the keyboard tray, first position the work-surface over the keyboard, then fold the keyboard tray/work-surfacetray
upward.
Adjusting Keyboard Tilt
The angle at which the keyboard tray sits when folded down for use can be adjusted between 0° and -10° from level. To
adjust the tilt angle, slightly raise the keyboard tray and then turn the Adjustment Knob, clockwise (CW) to decrease the
angle or counter-clockwise(CCW) to increase the angle. Lower the tray back down to verify the new tilt angle. Repeat
this process until the desired tilt angle is achieved.
Mouse Trays
There are two (2) mouse trays –one on the left and one on the right side. To access, grab the lip of the tray and pull
outward.

DU-FLP-0008-53Rev C 03/28/16 GCX Corp Page 6 of 6
Removing and Replacing Storage Bin
1. To remove, flex both sides of the Bin upward to disengage it from the mounting bracket.
2. To replace, place the Bin on the mounting bracket and flex both sides of the Bin upward while applying downward
pressure to reengage with the bracket –the Bin will snap into place when properly installed.
3. Snap opposite side on.
Cable Management
Keyboard and Mouse cables may be routed through slots located at the backside of the keyboard tray
Routine Maintenance
Periodically inspect all fasteners associated with the mounting assembly. Tighten or Adjust as necessaryfor optimal
operation and safety.
Cleaning the Mounting Assembly
1. The mounting assemblymay be cleaned with most mild, non-abrasive solutions commonlyused in the hospital
environment (e.g. diluted bleach, ammonia, or alcohol solutions).
2. The surface finish will be permanently damaged by strong chemicals and solvents such as acetone or
trichloroethylene.
3. Steel wool or other abrasive material should never be used.
4. Damaged caused by the use of unapprovedsubstances or processes will not be warranted. Werecommendtesting
of any cleaning solution on a small area of the mounting assemblythat is not visible to verifycompatibility.
5. Never submerge or allow liquids to enter the mounting assembly. Wipe any cleaning agents off the mounting
assembly immediatelyusing a water-dampened cloth. Dry the assembly thoroughly after cleaning.
CAUTION: GCX makes no claims regarding the efficacy of the listed chemicals or processes as a means for controlling
infection. Consult your hospital’s infection control officer or epidemiologist. To clean or sterilize mounted devices or
accessoryequipment, refer to the specific instructions delivered with those products.
2
1
1