GE Advantium CSB9120 User manual

Installation
Instructions
Advantium®120V
Built-In SpeedCook
Ovens
CSB9120
PSB9120
ZSC1201
ZSC1202
31-2000001
MFL59060920
08-16 GEA

Safety Information
2
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IMPORTANT —Save these instructions
for local inspector’s use.
IMPORTANT —Observe all governing codes
and ordinances.
•Note to Installer —Be sure to leave these
instructions with the Consumer.
•Note to Consumer —Keep these instructions
with your Owner’s Manual for future reference.
•Skill Level — Installation of this appliance
requires basic mechanical and electrical skills.
•Completion Time —1 Hour.
• Proper installation is the responsibility
of the installer. Product failure due to improper
installation is not covered under the warranty.
See Owner’s Manual for warranty information.
NOTE: This oven is only approved to be installed
under the specific models as labeled on this unit.
IMPORTANT —Use this oven only for its
intended purpose. Never use the oven for
warming or heating a room. Prolonged use
of the oven without proper ventilation can be
hazardous. For personal safety, remove
house fuse or oven circuit
breaker before beginning installation to avoid
severe or fatal shock injury.
For personal safety, the
mounting surface must be
capable of supporting the cabinet load, in
addition to the added weight of the oven and
drawer, plus additional oven loads.
If installing the Advantium
120V Oven below 36Ǝ,
you must use the plastic bottom trim due to
burn risk to children. The plastic trim acts as
insulation and will help prevent burns to children
from hot surfaces.If installing the Advantium
120V Oven below 36Ǝ, do not
remove the plastic door trim due to burn risk
to children. The plastic trim acts as insulation
and will help prevent burns to children from hot
surfaces.
MODELS AVAILABLE
Profile Models:
PSB9120WW–White*
PSB9120BB–Black
PSB9120SS–Stainless Steel
Monogram Models:
ZSC1201SS–Stainless Steel
ZSC1202SS–Stainless Steel**
Café Model:
CSB9120SS–Stainless Steel
*No color-matched drawer available for this
model.
**This unit cannot be installed with an
accessory storage drawer.
CONTENTS
Design Information
Models Available...............................................2
Product Dimensions and Clearances................3
Tools Required..................................................3
Parts Supplied...................................................3
Advance Planning .............................................3
Installation Preparation
Electrical Requirements ....................................4
Preparing the Opening (Standard).................5-8
Preparing the Opening (Flush Mount)..........9-10
Storage Drawer Preparation
Standard .........................................................11
Flush ...............................................................11
Installation Instructions
Step 1, Remove Packaging and Parts............12
Step 2, Door Trim Removal for above 36”
Installation only...............................................13
Step 3, Slide the Oven into the Cutout ...........13
Step 4, Install Bottom Trim..............................14
Step 5, Install Bottom Trim with Accessory
Drawer...........................................................14
Step 6, Install Mounting Screws......................14
Step 7, Finalize Installation.............................14
CAUTION
CAUTION
CAUTION
CAUTION

Design Information
3
PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model.
TOOLS AND PARTS REQUIRED
(NOT SUPPLIED)
•#2 Phillips screwdriver
•Hand-held drill
•High speed drill bit, 3/32Ǝdiameter
•3/8Ǝslot-head screwdriver
•Level
•Saw
•3/8Ǝmin. plywood for floor (if required)
•Wood screws or other hardware for installing
runner or shelf to support oven (if required)
•Safety glasses or goggles
ADVANCE PLANNING
•7KHVHRYHQVPD\EHLQVWDOOHGGLUHFWO\LQWRDƎ
wide oven cabinet with standard installation.
•Cutout height dimensions are different for
installations with an accessory storage drawer.
Make sure to use the correct cutout when
preparing the opening.
• Allow for clearance to adjacent corners, walls,
drawers, etc.
The oven must be securely installed in a cabinet
that is firmly attached to the house structure.
Weight on the oven door could cause the oven
to tip and result in injury. Never allow anyone to
climb, sit, stand or hang on the oven door.
If installing the drawer accessory, the drawer
must be assembled to the oven prior to
installation into the cabinet. See the Accessory
Storage Drawer Assembly Instructions.
21-1/2Ǝ
1Ǝ13Ǝ
19Ǝ
29-3/4Ǝ
1-3/5Ǝ
1-1/10Ǝ
FLUSH MOUNT INSTALLATION
(Monogram Only)
This installation method allows for the unit face to
be inline with the cabinet face.
IMPORTANT: HIGH SKILL LEVEL IN
CARPENTRY IS REQUIRED. Non-standard
cabinetry may be required.
Flush installation of the oven will lead to the
exposure of the cabinet face frame edges.
Side cleats may be visible and should be a
finished surface.

Installation Preparation
4
ELECTRICAL REQUIREMENTS
Single Advantium 120 Installation:
This product requires a 120-volt, 60 Hz, 15-amp
circuit and draws 1.8 kilowatts. This product must
be connected to a supply circuit of the proper
voltage and frequency.
• Wire size must conform to the requirements of
the National Electrical Code or the prevailing local
code for this kilowatt rating.
• The power supply cord and plug should be
brought to a separate 15 or 20 ampere branch
circuit single grounded receptacle. The outlet box
should be located within reach of the 48” power
cord.
ELECTRICAL LOCATION GROUNDING
INSTRUCTIONS
This appliance must be grounded. In the event of
an electrical short circuit, grounding reduces the
risk of electric shock by providing an escape wire
for electric current. This appliance is equipped
with a cord having a grounding wire with a
grounding plug. The plug must be plugged into
an outlet that is properly installed and grounded.
Improper use of the
grounding plug can result in a risk of
electric shock.
IMPORTANT: (Please read carefully).
The power cord of this appliance is equipped with
a three-prong (grounding) plug that mates with a
standard three-prong grounding wall receptacle
to minimize the possibility of electric shock.
Consult a qualified electrician or serviceman if
the grounding instructions are not completely
understood, or if doubt exists as to whether the
appliance is properly grounded.
• Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the consumer to have it replaced with
a properly grounded three-prong wall receptacle.
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
DO NOT USE AN EXTENSION CORD. If the
power supply cord is too short, have a qualified
electrician or serviceman install an outlet near the
appliance.
Install a recessed electrical outlet in the back
wall of the opening within 6Ǝof either side and
at least 9Ǝabove the cutout floor.
Locate outlet box in the shaded area
6”
9” WARNING

5
Standard Installation Preparation
PREPARE THE OPENING (CONT.)
Installation over a GE Appliances/
Monogram Warming Drawer:
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location does
not obstruct the required interior depth and height.
See Warming Drawer installation instructions for
details.
30” 23-1/2”
25-1/4”
17-1/2”
36-3/4”
Min.
2” Min.
(3” Recommended)
Per Warming
Drawer
Requirement
Construct
solid bottom
- Min. 3/8”
plywood
supported
on all four
sides. Must be
able to support
weight of oven
and contents.
PREPARE THE OPENING
The Advantium 120 can be installed in
combination with other GE Appliances/
Monogram appliances. Always follow each
product’s Installation Instructions to complete the
installation.
Single Advantium 120 Installation:
Order a 30” wide single oven cabinet or cut the
opening in a wall to the dimensions shown.
• Allow 1-1/4” case trim overlap
at the top and 7/8” overlap on the bottom and
2-1/4” overlap for each side of the opening.
• Oven overlaps will conceal cut edges on all
sides of the opening.
When installed over a single oven or a
warming drawer, allow at least 2” between
the two openings. This separation will provide
clearance for bottom overlap of the Advantium
120 and the other appliance overlaps.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
30” 23-1/2”
25-1/4”
17-1/2” Construct
solid bottom
- Min. 3/8”
plywood
supported
on all four
sides. Must
be able to
support
weight of
oven and
contents.
36-3/4”
Min.
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.

Standard Installation Preparation
6
PREPARE THE OPENING (CONT.)
Installation over a GE Appliances/
Monogram Oven and Warming Drawer:
NOTE: Additional clearances between the
cutouts may be required. Check to be sure
the oven supports above the Warming Drawer
location does not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
For personal safety, the
mounting surface must be
capable of supporting the cabinet load, in
addition to the added weight of the oven and
drawer, plus additional oven loads.
PREPARE THE OPENING (CONT.)
Installation over a GE Applainces/
Monogram Oven:
*If you are replacing a GE Appliances/
Monogram electric double oven with the
combined installation of an Advantium 120 and
a single oven, use the dimensions shown. The
middle rail separating the two openings may
need to be larger than the 2” minimum shown.
Construct
solid bottom -
Min. 3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
30” 23-1/2”
25-1/4”
17-1/2”
2” Min.
(3” Recommended)
Per Oven
Requirement
45-1/4”
2” Min.
(3” Recommended)
Per Warming
Drawer
Requirement
30” 23-1/2”
25-1/4”
17-1/2” 2” Min.
(3” Recommended)
45-1/4”
Min.
Construct
solid bottom
- Min. 3/8”
plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
Per Oven
Requirement
CAUTION
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.

7
Standard Installation Preparation
PREPARE THE OPENING (cont.)
Installation under a GE Appliances/
Monogram Microwave Oven and over a
Warming Drawer:
NOTE: Additional clearances between the
cutouts may be required. Check to be sure
the oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
For personal safety, the
mounting surface must be
capable of supporting the cabinet load, in
addition to the added weight of the oven and
drawer, plus additional oven loads.
PREPARE THE OPENING (cont.)
Installation over another GE Appliances/
Monogram Built-In SpeedCook Oven:
• If you are mounting a GE Appliances
Appliances/Monogram Built-In
SpeedCook
Oven over another, use the dimensions
shown.
The middle rail separating the two openings
may need to be larger than the 2Ǝminimum
shown.
30Ǝ23-1/2Ǝ
25-1/4Ǝ
17-1/2Ǝ2ƎMin.
(3ƎRecommended)
17-1/2Ǝ
Construct
solid bottom - Min.
3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
30Ǝ23-1/2Ǝ
25-1/4Ǝ
17-1/2Ǝ
2ƎMin.
(3ƎRecommended)
Per Microwave
Oven Requirement 3.5ƎMin.
(4.5ƎRecommended)
Per Warming
Drawer
Requirement
Construct
solid bottom - Min.
3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
CAUTION
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.

PREPARE THE OPENING (cont.)
Installation beside another GE
Appliances/Monogram Built-in
Speedcook Oven:
• If you are mounting a GE Appliances/
Monogram Built-In
SpeedCook Oven beside
another, use the dimensions shown. The
middle rail separating the two openings may
need to be larger than the 4-1/2Ǝminimum
shown.
25-1/4Ǝ
17-1/2Ǝ
Standard Installation Preparation
8
23-1/2Ǝ
17-1/2Ǝ
4-1/2ƎMin.
(5-1/2ƎRecommended)
PREPARE THE OPENING (cont.)
Installation under a GE Appliances/Monogram 30Ǝor 36ƎCooktop or Countertop:
Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the
cutout size. See the label on top of the oven for approved cooktop models. This oven requires a separate,
properly grounded 15-Amp, 120-Volt, 60Hz power supply. The cooktop requires a separate power supply.
Use a 36Ǝor wider base cabinet.
25-1/4Ǝ
Cooktop Cooktop
25Ǝ
1-1/2ƎMin.
4ƎHigh
Toekick
23-1/2Ǝ
25-1/4Ǝ
17-1/2Ǝ
36Ǝ
Countertop
Height
NOTE: The oven is only approved to be installed
under the specific models as labeled on the unit.
Cooktop height including depth
of electrical box on some
models. Refer to cooktop
installation instructions.
No minimum clearance required
between cooktop and oven.
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.

9
PREPARE THE INTERIOR
Cut and install side cleats:
• Cut side wood cleats to height of cabinet
opening and approx. 2-1/2” in depth. Install,
on each side, 1-3/8” from the front face of the
cabinet.
Cut and install bottom cleat:
• Cut bottom wood cleat to a height of 1-1/8”, a
depth of the cabinet minus 1-3/8” and a width
of 25-1/4” to fit between side cleats. Install
onto the cabinet floor between the side cleats,
push it all the way back against cabinet wall
and make sure its front face aligns with the front
faces of the side cleats (1-3/8” gap from the
front cabinet face).
Flush Mount Installation Preparation (Monogram Only)
A Side cleats depth 2-1/2” min.
B Bottom cleat height 1-1/8”
C Bottom cleat depth Cabinet depth minus 1-3/8”
D Bottom cleat width 25-1/4”
E All three cleats Recess and install 1-3/8”
IURPGHVLUHGÀXVKVXUIDFH
TOP
VIEW
Front Face of Cabinet
EE
A A
C
D
E
C
B
D
A A
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.
PREPARE THE OPENING
The Advantium 120 can be installed in
combination with other GE Appliances/
Monogram appliances. Always follow each
product’s Installation Instructions to complete the
installation.
Single Advantium 120 Installation:
Cut the opening in a cabinet to the dimensions
shown.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
**19-1/4”
Construct
solid bottom
- Min. 3/8”
plywood
supported on
all four sides.
Must be able to
support weight
of oven and
contents.
36-3/4”
Min.
F *
23-1/2” min.
2” Min.
*See table
below for
desired reveals
on sides.
Per
appliance
specs.
Oven or
warming
drawer
Approved Flush Installation Dimension F
1/8” Reveal 1/4” Reveal
Single Advantium 30” 30-1/4”
Over Warming Drawer 30” 30-1/4”
Over Oven 30” 30-1/4”
Over Oven and Warming Drawer 30” 30-1/4”
Over Built-in Speedcook Oven 30” 30-1/4”
Double Advantium (side by side) See page 10
Under Cooktop or Countertop See page 10
** Top and bottom reveals are set to 1/8”.

PREPARE THE OPENING
The Advantium 120 can be installed beside another
Advantium 120 in a side-by-side combination.
Double Advantium 120 Installation:
Cut the opening in a cabinet to the dimensions shown.
• Center divider acts as cleat for side of each respective
unit. Only one additional side cleat needed per oven
cutout.
• The support must be level and rigidly mounted, flush
with the bottom edge of the cutout. 19-1/4”
Construct solid bottom - Min. 3/8”
plywood supported on all four
sides. Must be able to support
weight of oven and contents.
36-3/4”
Min.
I*
23-1/2” min.
I*
H*
G*
1-3/8”
*See table for desired reveals on sides and
between unit.
10
Flush Mount Installation Preparation (Monogram Only)
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.
Cooktop Cooktop
25Ǝ
1-1/2ƎMin.
4ƎHigh
Toekick
23-1/2Ǝ
J* 19-1/4”
36Ǝ
Countertop
Height
NOTE: The oven is only approved to be
installed under the specific models as
labeled on the unit.
Installation under a GE Appliances/Monogram 30Ǝor 36ƎCooktop or Countertop:
Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout size.
See the label on top of the oven for approved cooktop models. This oven requires a separate from the cooktop,
properly grounded 15-Amp, 120-Volt, 60Hz power supply. Use a 36Ǝor wider base cabinet.
Cooktop height including depth of electrical box on some
models. Refer to cooktop installation instructions.
No minimum clearance required between cooktop and
oven.
Dimension 1/8” Reveal 1/4” Reveal
G 59-7/8” 60-1/4”
H 5-1/8” 5-1/4”
I 27-3/8” 27-1/2”
Dimension 1/8”
Reveal 1/4” Reveal
J 30” 30-1/4”
*See table for desired reveals on sides.

11
Installation Preparation
Preparation WITH an Accessory Storage Drawer
• PSB9120 is the only approved model to be installed under 36-3/4” height with a storage drawer.
CSB9120, ZSC1201 and ZSC1202 are not approved.
• As needed, see the Standard Mount Installation Preparation OR Flush Mount Installation Preparation
for configuration details. Note the modified cutout height below.
• Model ZSC1202 cannot be installed with an accessory storage drawer. See installation preparation
without an accessory storage drawer for this model.
STANDARD MOUNT
30Ǝ23-1/2Ǝ
25-1/4Ǝ
Min.
21Ǝ
36-3/4Ǝ
Min.
Construct
solid bottom - Min.
3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
FLUSH MOUNT (Monogram only)
23-1/2Ǝ
K*
22-5/8Ǝ
36-3/4Ǝ
Min.
Construct
solid bottom - Min.
3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
PREPARE THE OPENING (cont.)
The Advantium 120V can be installed in combination with other GE Appliances/Monogram appliances.
Always follow each product’s Installation Instructions to complete the installation.
Single Advantium 120V Installation:
Order a 30Ǝwide single oven cabinet or cut the opening in a wall to the dimensions shown.
• Allow 2-1/8Ǝcase trim overlap on the sides, 1-1/16Ǝoverlap on the top and 7/8Ǝoverlap on the bottom of
the opening for all models.
• Oven overlaps will conceal cut edges on all sides of the opening.
• When installed over a single oven or a warming drawer, allow at least 2Ǝbetween the two openings.
This separation will provide clearance for bottom overlap of the Advantium 120V and the other appliance
overlaps.
• The support must be level and rigidly mounted, flush with the bottom edge of the cutout.
Dimension 1/8”
Reveal 1/4” Reveal
K 30” 30-1/4”
*See table for desired reveals on sides.

1
REMOVE THE PACKAGING AND PARTS
12
Installation Instructions
• Remove all packing material and tape.
• Locate parts package containing mounting
screws.
• Remove the oven from the carton. Do not lift unit
by handle or conduit. Two people are required to
lift this oven.
• Open the door and remove any packaging in
oven.
Owner’s
Manual
Owner’s Manual Installation
Instructions
Glass Tray
Metal Trays (2)
Turntable Ring
Bottom Trim – Metal #1
IMPORTANT:If installing the Advantium 120V
Oven with an accessory storage drawer, read the
storage drawer assembly instructions to assemble
the products together before proceeding to Step 2.
If installing the Advantium 120V
Oven below 36Ǝ, you must use
the plastic bottom trim due to burn risk to children.
The plastic trim acts as insulation and will help
prevent burns to children from hot surfaces.
Cook Book
5 Color-Matched Screws
(4 required, 1 extra)
Cooking Guide
Cooking
Guide
Bottom Trim – Metal #2
Rack
CAUTION
3UR¿OH Cafe Monogram
Plastic Door Trim X X X
(ASSEMBLED)
Bottom Trim - Metal #1 X X -
Bottom Trim - Metal #2 - - X
Bottom Trim - Plastic X X X
Bottom Trim – Plastic
Plastic Door Trim
4 Color-Matched Flat-Head Screws
for the Plastic Door Trim (3 required,
1 extra)
*Some models already have the trim
and screws on the door
6 Brass Screws for the
Bottom Trim
(3 required, 3 extra)

Installation Instructions
13
3
SLIDE THE OVEN INTO THE
CUTOUT
Two people are required to lift
the oven into the opening. Grasp the bottom at
front and rear. DO NOT USE THE HANDLE TO
LIFT THE OVEN. DAMAGE WILL OCCUR.
• Lift and hold the oven at the front of the opening.
Hold the oven at an angle and plug in the power
cord.
• Carefully, slide the oven into the cabinet part
way. Leave the oven a few inches forward of
the cabinet frame.
• Check to be sure the power cord is not trapped
under the oven or along the sides of the oven.
2
DOOR TRIM REMOVAL FOR
ABOVE 36ƎINSTALLATION
ONLY
If installing the Advantium 120V Oven above 36Ǝ
from the floor, you may remove the plastic trim
from the bottom of the door for esthetic purposes
if desired.
•If installing above 36Ǝ, remove the 3 screws
that secure the plastic trim to the bottom of the
door.
•Discard plastic trim. Replace screws.
If installing the Advantium
120V Oven below 36s, do not
remove the plastic door trim due to burn risk
to children. The plastic trim acts as insulation
and will help prevent burns to children from hot
surfaces.
CAUTION
CAUTION

14
Installation Instructions
6
INSTALL MOUNTING SCREWS
•Slide the oven the remaining way into the
opening so that the side flanges and control
panel are against the cabinet frame. Make sure
that the oven is centered in the opening.
•Open the door, place a turntable tray in the oven
and make sure that the tray in the unit is level.
•Drill pilot holes through the side flanges.
•Drive the color-matched screws into the side
flanges. It is recommended that the screws
be hand tightened.
If installing oven with an accessory storage
drawer:
•Open the drawer.
•Drill pilot holes through the side flanges.
•Drive color-matched screws into the side flanges.
It is recommended that the screws be hand
tightened.
NOTE: If installing the Profile Advantium 120V
Oven with an accessory storage drawer, you
must use the Under-the-Counter (UTC) mounting
bracket for the drawer.
If installing the Monogram Advantium integrated
model ZSC1201 above 36Ǝ, the UTC mounting
bracket for the accessory storage drawer must be
used.
7FINALIZE INSTALLATION
•Turn power on at the source. The interior light
should come on when the door is opened.
•Refer to Owner’s Manual for operating
instructions.
4
INSTALL BOTTOM TRIM
If installing the Advantium
120V Oven below 36Ǝ, you
must use the plastic bottom trim due to burn risk
to children. The plastic trim acts as insulation
and will help prevent burns to children from hot
surfaces.
NOTE: If installing the Advantium 120V Oven
with an accessory storage drawer, the bottom
trim is not required. Proceed to Step 5.
•Installation Below 36Ǝ, align trim tabs on the
plastic trim to slots in the bottom of the oven.
•Installation Above 36Ǝ, align trim tabs on the
plastic or metal trim to slots in the bottom of the
oven.
•Secure the bottom trim to the bottom of the
oven using 3 screws provided.
5
INSTALL BOTTOM TRIM WITH
ACCESSORY DRAWER
If installing with an accessory drawer, see
installation instructions that come with the
accessory drawer.
Metal
Trim
Plastic
Trim OR
Plastic
Trim
CAUTION

15
Notes

Printed in Korea
NOTE: While performing installations described in this
book, safety glasses or goggles should be worn.
NOTE: Product improvement is a continuing endeavor
at GE Appliances. Therefore, materials, appearance and
specifications are subject to change without notice.

Instrucciones
de Instalación
Hornos con Velocidad de
Cocción Incoporada de 120V
de Advantium®
CSB9120
PSB9120
ZSC1201
ZSC1202
31-2000001
MFL59060920
08-16 GEA GE es una marca de la Empresa General Electric. Fabricado bajo licencia de la marca registrada.

Información sobre Seguridad
2
ANTES DE COMENZAR
Lea estas instrucciones en su totalidad y
atentamente.
IMPORTANTE —Conserve estas
instrucciones para uso del inspector local.
IMPORTANTE —Cumpla con todos los
códigos y ordenanzas gubernamentales.
•Nota para el Instalador —Asegúrese
de que el Comprador conserve estas
instrucciones.
•Nota para el Consumidor —Guarde estas
instrucciones con su Manual del Propietario
para referencia futura.
•Nivel de habilidad —La instalación de este
electrodoméstico requiere un nivel básico de
habilidades mecánicas y eléctricas.
•Tiempo de Compleción —1 Hora.
• Es responsabilidad del instalador realizar
una instalación adecuada. Si se producen
fallas en el producto debido a una instalación
inadecuada, la garantía no cubrirá las mismas.
Para obtener información sobre la garantía,
consulte el Manual del Propietario.
NOTA: Sólo se aprueba la instalación de este
horno de acuerdo con los modelos específicos
que aparecen etiquetados en esta unidad.
IMPORTANTE —Use este electrodoméstico
sólo para su propósito original. Nunca use el
electrodoméstico para calentar o calefaccionar una
habitación. El uso prolongado del horno sin una
ventilación adecuada puede ser riesgoso.
Para su seguridad personal, retire
el fusible del hogar o el disyuntor
abierto antes de comenzar la instalación, a fin de
evitar lesiones graves o una descarga mortal.
Para su seguridad personal, la
superficie de instalación deberá
poder soportar la carga del gabinete, además del
peso agregado del horno y el cajón, sumado esto a
las cargas adicionales del horno.
Si instalará el Horno
Advantium120V por debajo de
36”, deberá usar la moldura inferior de plástico
debido a riesgos de quemaduras de los niños. La
moldura de plástico actúa como aislante y ayudará
a evitar que los niños sufran quemaduras sobre las
superficies calientes.
Si instalará el Horno Advantium
120V por debajo de 36”, no retire
la moldura de plástico de la puerta debido al riesgo
de quemaduras de los niños. La moldura de plástico
actúa como aislante y ayudará a evitar que los niños
sufran quemaduras sobre las superficies calientes.
MODELOS DISPONIBLES
Modelo Profile:
PSB9120WW–Blanco*
PSB9120BB–Negro
PSB9120SS–Acero Inoxidable
PSB9120ES–Teja
Modelos de Monogram:
ZSC1201SS–Acero Inoxidable
ZSC1202SS–Acero Inoxidable**
Modelo de Café:
CSB9120SS–Acero Inoxidable
CMB7030SK–Acero Inoxidable
PSB9120ES –Teja
*Este modelo no cuenta con cajones
disponibles del mismo color.
**Esta unidad no puede instalarse con un cajón
de almacenamiento de accesorios.
CONTENIDOS
Información de Diseños
Modelos Disponibles.................................................2
Dimensiones y Espacios de Despeje del Producto..3
Herramientas Necesarias..........................................3
Piezas Suministradas................................................3
Planificación Anticipada............................................3
Preparación de la Instalación
Requisitos Eléctricos.................................................4
Preparación de la Abertura (Estándar)..................5-8
Preparación de la Abertura (Montaje al Ras)......9-10
Preparación del Cajón de Almacenamiento
Estándar..................................................................11
Al ras.......................................................................11
Instrucciones de Instalación
Paso 1, Retire el Embalaje y las Piezas.................12
Paso 2, Retiro de la Moldura de la Puerta sólo en
instalaciones superiores a 36”................................13
Paso 3, Deslice el Horno por la Abertura...............13
Paso 4, Instale la Moldura Inferior..........................14
Paso 5, Instale la Moldura Inferior con el Cajón de
Accesorios...............................................................14
Paso 6, Instale los Tornillos de Montaje.................14
Paso 7, Finalice la Instalación................................14
PRECAUCIÓN
PRECAUCIÓN
PRECAUCIÓN
PRECAUCIÓN

Información de Diseños
3
DIMENSIONES Y ESPACIOS DE DESPEJE DEL PRODUCTO
NOTA:El aspecto variará dependiendo del modelo.
HERRAMIENTAS Y PIEZAS
REQUERIDAS (NO SUMINISTRADAS)
•Destornillador Phillips nº 2
•Perforadora manual
•7DODGURGHDOWDYHORFLGDGGLiPHWURGHƎ
•'HVWRUQLOODGRUFRQSXQWD3KLOOLSVGHƎ
•Nivel
•Sierra
•&RQWUDFKDSDGRSDUDSLVRGHXQPtQGHƎVL
se requiere)
•Tornillos de madera y otras herramientas para
instalar el riel o el estante para sostener el
horno (si se requiere)
•Anteojos o gafas de seguridad
PLANIFICACIÓN ANTICIPADA
•Estos hornos pueden ser instalados directamente
en un gabinete para horno de 30” de ancho,
utilizando la instalación estándar.
•Las dimensiones de altura de la abertura son
diferentes para las instalaciones con un cajón de
almacenamiento de accesorios. Asegúrese de usar
el recorte correcto al preparar la abertura.
• Deje espacio en relación a las esquinas
adyacentes, paredes, cajones, etc.
El horno debe ser instalado de forma segura en
un gabinete que esté adherido de manera firme
a la estructura de la casa. Cualquier peso sobre
la puerta del horno podrá hacer que éste se
incline y se produzcan lesiones. Nunca permita
que nadie se trepe, siente, pare ni cuelgue de la
puerta del horno.Si instalará el accesorio para
cajones, el cajón deberá ser ensamblado al horno
antes de la instalación en el gabinete. Consulte
las Instrucciones de Ensamble del Cajón de
Almacenamiento de Accesorios.
21-1/2Ǝ
1Ǝ13Ǝ
19Ǝ
29-3/4Ǝ
1-3/5Ǝ
1-1/10Ǝ
INSTALACIÓN DEL MONTAJE AL
RAS (Monogram únicamente)
Este método de instalación permite que la cara
de la unidad quede alineada con la cara del
gabinete.
IMPORTANTE: SE REQUIERE UN NIVEL
DE HABILIDAD ALTO EN CARPINTERÍA. Se
podrán adquirir gabinetes no estándares.
La instalación al ras del horno hará que se
expongan los extremos del marco de la cara del
gabinete.
Los ristreles laterales podrán quedar visibles y
deberán poseer una superficie acabada.

Preparación de la Instalación
4
REQUISITOS ELÉCTRICOS
Instalación Simple del Advantium 120:
Este producto requiere un circuito de 120 voltios,
60 Hz, 15 amperes y consume 1.8 kilowatts. Este
producto se debe conectar a un circuito con un
suministro correcto de voltaje y frecuencia.
• El tamaño del cable deberá ser conforme a los
requisitos del Código Eléctrico Nacional o del
código local obligatorio con relación a la cantidad
de kilowatts.
• El cable y el enchufe de suministro de corriente
se deberán conectar al tomacorriente simple con
conexión a tierra de un disyuntor de entre 15 y 20
amperes. La caja del tomacorriente deberá ser
ubicada dentro del alcance del cable de corriente
de 48”.
UBICACIÓN ELÉCTRICA
INSTRUCCIONES DE
CONEXIÓN A TIERRA
Este electrodoméstico deberá estar conectado
a tierra. En caso de que se produzca un
cortocircuito, la conexión a tierra reduce el
riesgo de descarga eléctrica, brindando un
cable de escape de la corriente eléctrica. Este
electrodoméstico está equipado con un cable de
corriente que posee un cable de conexión a tierra
con un enchufe a tierra. El enchufe se deberá
colocar en un tomacorriente instalado y conectado
a tierra de forma adecuada.
El uso inadecuado del
enchufe de conexión a
tierra puede provocar riesgos de descargas
eléctricas.
IMPORTANTE: (Se solicita leer
detenidamente).El cable de corriente de este
electrodoméstico cuenta con un enchufe de 3
clavijas (con cable a tierra) que se conecta a un
tomacorriente de pared estándar de 3 clavijas
para minimizar la posibilidad de descargas
eléctricas. Consulte a un electricista calificado o al
personal del servicio técnico en caso de que las
instrucciones de conexión a tierra no se entiendan
completamente, o si tiene dudas sobre si el
electrodoméstico está conectado a tierra de forma
apropiada.
• En caso de contar con un receptáculo de pared
de dos clavijas, es la responsabilidad y obligación
del cliente reemplazarlo por un tomacorriente de
pared de tres clavijas correctamente conectado a
tierra.
Nunca, bajo ninguna circunstancia, corte ni elimine
el tercer cable (tierra) del cable de corriente.
NO USE UN PROLONGADOR. Si el cable
de corriente es demasiado corto, solicite a un
electricista calificado o al personal del servicio
técnico que instale un tomacorriente cerca del
electrodoméstico.
Instale un tomacorriente eléctrico empotrado en
la pared trasera de la abertura, dentro de las 6”
de cualquiera de los lados y a por los menos 9”
sobre el piso del recorte.
Ubique la caja del tomacorriente en
el área sombreada.
6”
9”
ADVERTENCIA