GE PB909SP3SS User manual

[
• All ranges can tip.
• BURNS or other SERIOUS
INJURIES can result.
• INSTALL and CHECK the
ANTI-TIP bracket following
the instructions supplied
with the bracket.
STEP 1 LOCATE THE BRACKET
IMPORTANT: Determine the final location of the range
before attempting to install the bracket.
a. Place the bracket on the floor with the back edge against
the rear wall. If the range does not reach the rear wall,
align the back edge of the bracket with the rear panel of
the range in its final location.
RearWall
Adjacentcabinetor
final locationofrange
sidepanel
LocA
LocC
LecB
Two screws must enter floor
orwall atLecA, BerC.
ir bracket does not touch the rear wall, gou MUST
screw bracket to FLOORas described in Step 2.
b. Position the side of the bracket against either the left or
right cabinet. If there is no adjacent cabinet, align the
edge of the bracket with the side panel of the range in
its final location. Ifthe countertop overhangs the
cabinet, offset the bracket from the cabinet bg the
amount of overhang.
c. Mark the location for the pair of holes to be used (see
illustration above).
NOTE: For FLOORinstallation use either Loc A or B.For
REARWALL installation use Loc C.
31-10671 ]
04-08 JR
Toreduce the RISKOFTIPPINGthe range, the range must be
secured bg a properly installed ANTI-TIPBRACKET.
Secure the bracket with the screws provided.
NOTE:Theinstallation of the ANTI-TIPbracket must meet all
local codes for securing the appliance.
If gou did not receive an anti-tip bracket with gour purchase,
call 1-800-626-8774 to receive one at no cost.
In Canada, call 1-800-561-3344,
For installation instructions of the bracket, visit: GEAppliances.com.
In Canada, GEAppliances.ca.
STEP 2 SECURE THE BRACKET
The bracket must be screwed to either the FLOORor REAR
WALL.
Attachmentto Flooror RearWall
Bracket Wall Sill Plate
/Screwmustenter "_
__] wood orconcrete
Screw mustenterwood
FLOOR Installation:
WOOD FLOOR:Use the screws provided to secure the
bracket using the pair of marked holes (either Loc A or B).
CONCRETEFLOOR:Using a concrete bit, drill a 5/32" pilot
hole 2" deep into the concrete at the center of each of the
marked holes (either Loc A or B). Use the screws provided to
secure the bracket into the floor.
REARWALL Installation:
Use the 2 screws provided to secure the bracket using the
pair of marked holes at Loc C.The screws MUST enter into
a wood sill plate. Ifthe wall contains ang metal studs or
similar materials, then the floor must be used.
STEP 3 CHECKTHE BRACKET
After installing the bracket, slide the range into its final
location. The rear leveling leg must be fullg inserted into the
ANTI-TIP bracket. Ifthe range has a storage drawer, remove
the drawer and look underneath the range to see if the leg
is fullg engaged in the bracket as shown in Step !.
On models without storage drawer or kickpanel, verifg the
rear leveling leg is properlg secured within the bracket bg
carefullg tipping the range forward. DO NOTtip the range
more than 4 inches. If the bracket does not stop the range
within 4 inches, the bracket is NOT properlg installed and
MUSTbe reinstalled following these instructions.
A he anti-tip bracket must be PROPERLYINSTALLEDand
the rear leveling leg must be FULLY ENGAGEDinto the
bracket to prevent the range from tipping. NEVER
remove the leveling legs. This will prevent the range
from being secured to the ANTI-TIP bracket properlg.

•Todaslascocinaspuedenvolcarse.
• PuedenprovocarseQUEMADURASu
otrasLESIONESGRAVES.
• INSTALEgCONTROLEelsoporte
ANTI-VOLCADURASsiguiendolas
instruccionessuministradascon
elsoporte.
ParareducirelRIESGODEVOLCARlacocina,@stadebesujetarse
medianteun SOPORTEANTI-VOLCADURASconunaadecuadainstalaci6n.
Fijeelsoporteconlostornillosprovistos.
NOTA:Loinstataci6ndetsoporteANTI-VOLCADURASdebecumptir
contodoslosc6digoslocalesparaaseguraretaparato.
Siustedno recibi6unsoporteanti-volcadurasconsucompra,Ilameal
1-800-626-8774pararecibirunosincostaalguno.
EnCanad6,Ilameal 1-800-561-3344.
Parainstruccionesde instalaci6ndelsoporte,visite:GEAppliances.com.
EnCanad6,GEAppliances.ca.
PASO 1 UBIOUE ELSOPORTE
IIvlPORTANTE:Determine la ubicaci6n final de la cocina
antes de tratar de instalar elsoporte.
a. Coloqueel soporte en el pisocon el lado trasero sabre la
pared trasera. Sila cocina no Ilegaa la pared trasera,
alinee el lado trasero del soporte con el panel trasero de
la cocina en su ubicaci6n final.
Gabineteadyacenteo
ubicaci0nfinal delpanel
lateraldela cocina
\
Paredtrasera
Ubic. C
Ubic.A Ubic.B
Dostornillos debeningresar
enel pisoopared en la
Ubic.A, Bo C.
Siel soporte no toca la pared trasera, usted DEBE
atornillar el soporte al PlSOcoma sedescribe en el
Paso2.
b. Coloque el lado del soporte sabre el gabinete izquierdo o
derecho. Si no hay un gabinete adyacente, alinee el
extremo del soporte con el panel lateral de la cocina en
su ubicaci6n final. Si el mostrador de encimera sobresale
del gabinete, modifique la posici6n del soporte desde el
gabinete considerando la cantidad que sobresale.
c. Marque la ubicaci6n para el par de orificios que se
utilizar6n (vet la ilustraci6n de arriba).
NOTA: Para instalaciones de PISO utilice la Ubic. A o B.
Para la instalaci6n de PAREDTRASERAutilice la Ubic. C.
31-10671 ]
PASO 2 SUJETE ELSOPORTE
Elsoporte debe atornillarse al PISOoa la PAREDTRASERA.
SujeciOnal pisoo la paredtrasera
Saparte
Eltornilledebe
ingresarenmadera
__J oconcrete
Umbraldela pared
Instalaci6n de PISO: Eltornillo debeingresarenmadera
PISODEMADERA:Utilicelos tomillos provistospara sujetar el
soporte utilizando el par de orificios marcados (Ubic.A oB).
PISODECONCRETO:Utilizando unabroca para concreto, perfore
un orificio piloto de 5/32" de 2" de profundidad dentro del
concreto en el centro de cada uno de los orificios marcados (Ubic.
A o B). Utilicelos tornillos provistos para sujetar el soporte al piso.
Instalaci6n de PAREDTRASERA:
Utilice los 2tomillos provistos para sujetar el soporte utilizando el
par de orificios marcados en Ubic. C.Lostomillos DEBENingresar
en el umbral de madera. Si lapared contiene parantes de metal o
materiales similares, entonces debe usarse el piso.
PASO 3 VERIFIOUE ELSOPORTE
Despu@sdeinstalar el soporte,deslicela cocina asuubicaci6n final.
Lapata de nivelaci6ntrasera debeintroducirse par completo en el
soporte ANTI-VOLCADURAS.Sila cocina cuenta con el caj6n de
almacenamiento, quite el caj6n Umire debajo de la cocina para vet
si la pata estd bien enganchada en el soporte coma puedeverseen
el Paso!.
En modelos sin guanteras ni paneles delanteros inferiores,
verifique que lapata de nivelaci6ntrasera seencuentrebien
asegurada dentrodelsoporte inclinandocon cuidadola cocina hacia
delante. NOinclinela cocina mds de4 pulgadas.Sielsoporteno
detiene la cocina dentrode las4 pulgadas,elsoporte NOest6bien
instalado UDEBEvolver a instalarse siguiendoestasinstrucciones.
A I soporte anti-volcaduras debe INSTALARSEDEMANERA
CORRECTAUla pata denivelaci6n trasera debe ENGANCHARSE
BIENal soporte para evitar que la cocina vuelque. NUNCAquite
las patas de nivelaci6n.Estono permitird quela cocina quede
bien sujeta al soporteANTI-VOLCADURAS.
04-08 JR