Teknatool NOVA 1624 User manual
Nova 1624 Stand 113-0610-002
NOVATM 1624 LATHE STAND
For safety reasons please carefully read and understand these instructions.
The NOVA 1624 Stand is designed to fit and be used only with the NOVA DVR XP and 1624-44 Woodlathes. Use
of the 1624 Stand on other lathes could cause a malfunction and risk of serious injury.
If you are unsure of the use or application of this accessory contact the technical manager of Teknatool
International or your reseller.
Parts List
Part Code Description No
1 25045 Cast Iron Frame 2
2 25046 Leg Stand RHS R 2
3 25047 Leg Stand RHS L 2
4 25050 Bolt Ball Pin 4
4a 25051 Rubber Bushing 4
5 25052 Casted Foot 4
6 CBNZ12090 Coach Bolt M12x90 8
7 SW12 Spring Washer M12 14
8 NHZ12 Nut Hex ZP M12 18
9 FW12 Heavy Flat Washer M12 14
10 BNMZ12040 Bolt Hex M12 x 40 6
11 BNMZ10035 Bolt Hex M10x 35 2
12 SW10 Spring Washer M10 2
13 FW10 Heavy Flat Washer M10 2
14 25053 Bolster Plate 4
Suggested Tools for
Assembly
•Ratchet and M10
socket
•At least a second
Person
•Saw benches or
workshop bench
both need to be
greater than at least
860mm (33 7/8”).
•5/8” or 16mm Ring/
Open End Spanner
•3/4” or 19mm
Ring/Open End
Spanner
•8” Adjustable
Spanner
Nova 1624 Stand 113-0610-002
ASSEMBLY INSTRUCTIONS
1. Remove the 2 cast iron frames
and the cardboard box
containing the legs.
2. Open the cardboard box and
identify the parts against the
parts lists provided (above)
3. Attach each of the feet by inserting the rubber bushing in the socket of
the foot and then pressing the ball at the end of each leg piece into
the bushing. The rubber will form around the ball firmly holding it into
the socket. (Pre-Assembled)
4. Of the four legs,
identify the two
different angles. With
the cast iron foot flat
on the floor, the leg
will angle either to the
left or right. Angled to
the right will go on the
left end of the stand.
Angled to the right will
go the right end of the
lathe.
5. With the cast iron frame on the floor add the appropriate legs into the
corners and insert the bolster plate, coach bolts, washer and nut
6. Repeat for other cast iron frame.
7. You will now have a leg set for each end of the lathe.
8. Now this is where you need a second person
and a table, saw horses or workshop bench of
suitable height. (If the table is not high enough then
you may need to put blocks underneath.) With the
help of a second person, move the lathe from the
box and up to the bench or onto the saw horses. It
may be easier to cut the box away in order to
prevent any dangerous loading on your back.
•Information 1
i. There’s a retaining bolt holding the swivel
pin of the headstock down on the
mainbed. Therefore the lathe can be
safely lifted via the headstock without the
need of the headstock lockpin.
•Important 2
ii. Check the tailstock is securely fastened
by tightening the lock arm.
•Once the following checks have been made
the headstock and the tailstock can be used to
assist in the lifting of the lathe.
9. Move the lathe on the bench so that the tailstock end is overhanging and
accessible. Attach the legs sloping to the right on this end. Drop the
M10 x 90 hex bolts through the holes and then fasten underneath with
the washer and nut.
Nova 1624 Stand 113-0610-002
10. Next do the headstock end.
Note that the left most
fastenings are inserted upward
into two blind holes into the
lathe bed
11. Level the lathe - The height
could be adjusted by adjusting
the nut on the feet.
12. For further lathe assembly
instruction see main manual pg.
9-16
TEKNATOOL INTERNATIONAL
7D Dallan Place, Albany, North Shore City, Auckland, New Zealand 0632
Ph: +649-477-5600
TEKNATOOL USA INC
4200 28th St N, St Petersburg. FL 33714, USA
Ph: 727-954-3433 or 1-866-748-3025
WEBSITE: www.teknatool.com
Product information, technical help desk and videos.
