GE 26607 User manual

Universal Remote
Instruction Manual
Control Remoto Universal
Manual de Instrucciones
26607
7252
TV CBL DVR DVD
SAT
AUDIO
AUX2
AUX1
A B C D
MUTE
LAST
VOL
++
CH
OK
123
456
7 8 9
0
DVR LIST
MENU SHIFT
SETUPINFO
INPUT
GUIDE
EXIT

2
Scan this to view remote
setup video
Mira a ver el video de
instalación remota
http://www.jascoproducts.com/remote
Congratulations on your purchase of the GE Universal
Remote Control. The GE Universal Remote Control
is one of the most easy-to-use remote controls
available today. With the GE Universal Remote
Control, juggling multiple remote controls is a thing of
the past! Your GE Universal Remote Control, controls
multiple devices, including the most popular brands
of TVs, DVRs, DVDs, CBL and SAT. The GE Universal
Remote Control is easy to use and easy to program,
and it gives you total control — at the touch of your
fingertips!
IMPORTANT: SAVE THIS MANUAL AND CODE LIST
FOR FUTURE REFERENCE
Introduction..................................................................................... 2
Setup .................................................................................................. 3
Battery Installation............................................................... 3
Battery Saver........................................................................... 3
Code Saver ............................................................................... 3
Button Functions ................................................................... 4
Programming Your Remote..................................................... 6
Direct Code Entry................................................................... 6
Auto Code Search ................................................................. 8
Favorite Function .................................................................. 9
Controlling Combo Devices............................................10
Using Your Remote....................................................................11
Using SHIFT............................................................................11
Master Volume Feature....................................................12
Code Identification .............................................................13
Reset to Factory Settings........................................................13
Troubleshooting..........................................................................14
Warranty ........................................................................................15
FCC Statement.............................................................................16
Table of Contents

3
Your universal remote requires two (2) AAA batteries
(not included). Alkaline batteries are recommended.
Battery Installation
1. On the back of the remote, pull down on
the textured surface and slide battery cover
downward to remove.
2. Match the (+) and (-) marks on the batteries to the
(+) and (-) marks inside the battery compartment,
then insert two (2) AAA batteries. Be sure to use
fresh batteries.
3. Position battery cover slightly below opening and
push upward to lock into place.
NOTE: If your remote stops operating properly,
replace the batteries with new ones. The remote will
retain the codes you have programmed for up to 10
minutes after the batteries are removed.
Battery Precautions
• Donotmixoldandnewbatteries.
• Donotmixalkaline,standard(carbon-zinc),or
rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
• Alwaysremoveold,weakorworn-outbatteries
promptly and recycle or dispose of them in
accordance with local and national regulations.
Battery Saver
Your remote automatically turns off if the buttons are
depressed more than 8 seconds. This will save your
batteries should your remote get stuck in a place
where the buttons remain depressed (e.g., between
the sofa cushions).
Code Saver
You will have up to 10 minutes to change the
batteries in your remote without losing codes you
have programmed. However, do not press any
buttons until batteries are installed in the remote. If
buttons are pressed without batteries in the remote,
all codes will be lost.
Setup

4
Button Functions
ENTER
For some TV models,
used after direct
channel number entry
to immediately change
to the selected channel.
MUTE Turns off the
TV sound while the
picture remains.
RECORD, PLAY, STOP,
REW, FF, PAUSE
TV, CBL, DVR, DVD, SAT,
AMP, AUX 1, AUX 2
Selects device
to control.
Red Indicator lights when
any button is pressed.
UP, DOWN,
LEFT & RIGHT
Navigation buttons.
ABCD (yellow, blue,
red and green) Allows
access to additional
features for DVRs,
cable box, satellite,
Blu-ray™, etc...
(additional features vary by
device type and brand, see
device owner's manual for
information).
GUIDE Displays satellite
or cable on-screen
program guide.
MENU Displays the
Menu on the TV.
DVR LIST Displays list of
recorded programs
TV CBL DVR DVD
SAT
AUDIO AUX2
AUX1
A B C D
MUTE
LAST
VOL
+
CH
OK
123
456
7 8 9
0
DVR LIST
MENU SHIFT
SETUPINFO
INPUT
GUIDE
EXIT

5
OK Selects menu items for the
device you are controlling.
Button Functions, cont.
DOT: Used to select
digital channels, e.g., 2.3.
VOLUME UP/DOWN
Changes the volume
level of the device,
normally the TV.
NUMBERS
Enter numbers for direct
channel selection. Some
devices require ENTER
to be pressed after
channel selection.
ON•OFF Turns
devices On or Off.
CHANNEL UP/DOWN
Changes the channels.
SETUP Used to
setup the remote,
and for code
search function.
INPUT Selects the video inputs
from available viewing sources.
Info (i) Displays
on-screen channel
information, etc.
EXIT
Exits On-Screen Menus.
LAST Returns to the
previously selected
channel, or DVD
repeat toggle.
SHIFT is the alternate
function of this button.
Use the SHIFT button to
access the menu and
DVR list of your device.
To enter the SHIFT
mode press this button
once. To exit the shift
mode, press the
SHIFT button again.
TV CBL DVR DVD
SAT
AUDIO AUX2
AUX1
A B C D
MUTE
LAST
VOL
+
CH
OK
123
456
7 8 9
0
DVR LIST
MENU SHIFT
SETUPINFO
INPUT
GUIDE
EXIT

6
Programming Your Remote
Your GE universal remote control is designed to
control multiple audio/video devices such as a TV,
DVD, DVR, satellite, cable and audio device using
only one remote. To use this remote, you will need to
program it to control the devices of your choice. There
are two ways to program the remote - direct code
entry or auto code search.
Direct Code Entry (Recommended)
1. Locate the Remote Code List provided
in this manual. Find the DEVICE
CATEGORY you wish to program (for
example TV, CBL, DVR, DVD, SAT,
AMP, AUX 1, AUX 2) and then find the
BRAND of that device. Circle all the
codes under that brand. Example: For
a GE TV, locate the TV code section
then circle all of the GE TV codes.
2. Manually turn on the device you wish
to control.
3. Press and hold the SETUP button
until the red indicator light stays on
(approximately 2 seconds) and then
release the SETUP button.
4. Press and release the device button on
the remote (TV, CBL, DVR, DVD, SAT,
AMP, AUX 1, AUX 2). The red indicator
will blink once and then remain on.
5. Enter the first 4-digit code previously
found in the code list using the
number buttons on the remote. If the
code entered is a valid code, the red
indicator light will turn off. If the code
entered is not a valid code, the red
indicator light will flash and remain on
allowing you to re-enter the code.
Note: If no buttons are pressed for 35
seconds, the remote will exit the SETUP
mode and you will have to start over.

7
Programming Your Remote, cont.
6. Point the remote at the device. Press
the POWER button—if the device
turns off, no further programming is
required for that device. If the device
does not turn off, return to step 3 and
use the next code found in the code
list. Continue this process until a code
for your device is found.
7. Repeat this process for each device
(for example TV, CBL, DVR, DVD, SAT,
AMP, AUX 1, AUX 2) in your home
entertainment system you wish
to control.
Programming Notes
• Ifyourdevicedoesnotrespondtotheremoteafter
trying all codes listed or your brand is not listed in
the code list, use the Auto Code Search method to
program your remote.
• Sometimestherstcodethat“works”withyour
device may operate only a few functions of your
device. There may be another code in the code
list that performs more functions. Try other codes
from the code list for more functionality.
• WiththeDirectCodeEntrymethod,youcan
program any device button to control any device
in your home entertainment system.
For example, you can use the DVR or AUX device
button to control an audio receiver or a DVD, VCR,
satellite device, etc.
• Forcombinationdevices,youmayhavetoentera
code for each device. For example, for a VCR/DVD
device, you may have to enter a code for the DVD
under the DVD button and enter a code for the
VCR using a different device button on the remote.
• Writedownthecodefoundtooperateyourdevice
for future reference.

8
Programming Your Remote, cont.
Auto Code Search
The Auto Code Search searches automatically through
the codes stored in this remote. Read all the following
steps prior to starting the auto code search as you will
need to be prepared to lock-in the proper code when
found.
1. Manually turn on the device you wish
to control.
2. Press and hold the SETUP button
until the red indicator light stays on
(approximately 2 seconds) and then
release the button.
3. Press and release the desired device
button on the remote (TV, CBL, DVR,
DVD, SAT, AMP, AUX 1, AUX 2) the
type of device you wish to control. The
red indicator will blink once and then
remain on.
4. Point the remote at the device and
press and release the POWER
button (for TV) or PLAY button (for
DVD, VCR, etc.) to start the search. The
red indicator will flash
(approximately every 2 seconds) as
the remote searches. Note: The remote
must be pointed at the device for the
duration of this search.
5. Place your finger on the #1 button so
you are prepared to lock-in the code.
6. When the device shuts off or begins
playing, press the #1 button to lock-in
the code. The red indicator light will
turn off. Note: You have approximately
two seconds after the device shuts off
or begins playing to lock-in the code.
7. Point the remote at the device and
check to see if the remote operates
the device as desired. If it does, no
further programming is required for
that device. If it does not, return to step
2 and start the auto code search again.

9
Programming Your Remote, cont.
8. Repeat this process for each device (for example
TV, DVD, SAT, AUX) in your home entertainment
system you wish to control.
Programming Notes
• Thisprocessmaytakeseveralminutesasthe
remote contains many codes.
• WhenusingtheAutoCodeSearchprogramming
method, the device button corresponding to
the type of device you want to control must be
selected (for example, the TV device button must
be selected in step 3 if you want to control a TV,
the DVD device button for a DVD player, etc.)
• TheSETUP button can be used during the search
process to reverse the direction of the search of
the remote codes. For example, if you miss the
code for your device and the remote is continuing
to search (as indicated by the blinking red light),
press the SETUP button and the code search will
reverse direction and return to the code.
• Sometimestherstcodethat“works”withyour
device may operate only a few functions of your
device. There may be another code in the code
list that performs more functions. Continue the
auto code search as directed above until the best
code is found.

10
Programming Your Remote, cont.
Controlling Combo Devices
Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two different Mode
buttons to control both parts of the Combo device.
For example, if you have a TV/DVD Combo, you might
need to set up one code under the TV button to
control the TV part AND a separate code (under any
other Mode button) to control the DVD part.

11
Using Your Remote
For MENU, press and release
SHIFT/SETUP then INFO/MENU.
For EXIT, press and release
SHIFT/SETUP then /EXIT.
For DVR List press and release
SHIFT/SETUP then DVR LIST/GUIDE.
SPECIAL NOTE: Remote will stay in shift mode
until the SHIFT button is pressed again, or until 10
seconds of inactivity. The red indicator light will
blink when the remote is in shift mode.
Using SHIFT for Menu and Navigation
The SHIFT button allows access to more than one
function for certain buttons.
Use the SHIFT/SETUP button prior to accessing
the MENU, GUIDE OK, EXIT and Navigation functions,
for example:

12
Master Volume Feature
The Master Volume Feature allows you to select a
single device (TV or audio receiver) that the volume
control always controls. For example, the remote can
be in TV mode while the volume buttons control the
volume on your audio receiver instead of your TV.
Enabling the Master Volume Feature
1. Press and hold the SETUP button
until the red indicator stays on
(approximately 2 seconds) and then
release the button.
2. Press and release desired device
button (TV, CBL, DVR, DVD, SAT, AMP,
AUX 1, AUX 2) for the device you wish
to setup to always control the volume.
3. Press and release the MUTE button.
4. Press and release the VOL + button.
The red indicator will blink twice and
then go off.
To test the feature put the remote in
another mode such as the TV mode if
you programmed the audio receiver to
be the Master Volume Device. Point the
remote at the audio receiver, press and
hold either the VOL - or the VOL + button.
If the audio receiver volume changes then
the remote is programmed correctly. If
the TV volume changes and not the audio
receiver, you will have to repeat the steps
above and test again.
Disabling the Master Volume Feature
1. Press and hold the SETUP button
until the red indicator stays on
(approximately 2 seconds) and then
release the button.
2. Press and release the device button
(TV, CBL, DVR, DVD, SAT, AMP, AUX
1, AUX 2) which is programmed to
control the Master Volume Feature.
Using Your Remote

13
Using Your Remote, cont.
3. Press and release the MUTE button.
4. Press and release the VOL - button.
The red indicator light will blink twice
and go off.
Code Identification
1. Press and hold the SETUP button
until the red indicator stays on
(approximately 2 seconds) and then
release the button.
2. Press and release the desired device
button (TV, CBL, DVR, DVD, SAT, AMP,
AUX 1, AUX 2) you would like the
code for.
3. Press and release ENTER button.
4. Press and release the #1 button.
Count the number of times the
remote light flashes. This is the
number corresponding to the first
digit of the code. Repeat the process
by pressing the #2, #3 and #4
buttons for the remaining digits.
5. Press and release ENTER button to
exit this mode.
Reset to Factory Settings
1. Press and hold the SETUP button
until the red indicator stays on
(approximately 2 seconds) and then
release the button.
2. Press and release the MUTE button.
3. Press and release the number #0
button. The red indicator light will
flash twice.

14
Remote does not operate your device.
• Pressthedevicebuttonofthedeviceyou
wish to control.
• Programtheremotewithanewcode.
• Installnewbatteries.(Youmighthaveto
reprogram your remote after installing new
batteries.)
• Remotemaynotbecompatiblewithyourdevice.
Remote does not operate some features of
your device.
• Sometimesaparticularcodemightoperatesome
features but not all. Try programing remote with a
new code.
• Remotemaynotbeabletooperateallfeaturesof
your device or button names might be different
than your device.
Red Indicator blinks and stays on after you
program a product code.
• Remotedidnotacceptthecode.
• Trytoprogramthecodeagainortrya
different code.
Remote Code is not available for a device
(e.g. TV/VCR)
• Seesectionforcontrollingcombodevices.
Troubleshooting

15
90-Day Limited Warranty
Jasco Products Company warrants this product to be
free from manufacturing defects for a period of ninety
days from the original date of consumer purchase.
This warranty is limited to the repair or replacement
of this product only and does not extend to
consequential or incidental damage to other products
that may be used with this unit. This warranty is in
lieu of all other warranties express or implied. Some
states do not allow limitations on how long an implied
warranty lasts or permit the exclusion or limitation of
incidental or consequential damages, so the above
limitations may not apply to you. This warranty gives
you specific rights, and you may also have other
rights which vary from state to state. If unit should
prove defective within the warranty period, return
prepaid with dated proof of purchase to:
Jasco Products Company
10 East Memorial Road
Oklahoma City, OK 73114
www.jascoproducts.com
Made in China
This Jasco Products comes with a 90 day limited
warranty. Visit www.jascoproducts.com for warranty
details. Questions? Contact us at 1-800-654-8483
between 7:30AM—5:00PM CST.
If you have any questions or would like
additional information please, visit our web site
www.jascoproducts.com, or contact our
Technical Support Group at 1-800-654-8483,
Monday-Friday 7:30am-5:00pm.

16
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
FCC NOTE: The manufacturer is not responsible for
anyradioorTVinterferencecausedbyunauthorized
modifications to this equipment. Such modifications
could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encourage to try to correct
the interference by one or more of the following
measures:
•Reorientorrelocatethereceivingantenna.
•Increasetheseparationbetweentheequipment
and receiver.
•Connecttheequipmentintoanoutletona
circuit different from that to which the receiver is
connected.
•Consultthedealeroranexperiencedradio/TV
technician for help.
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme á
la norme NMB-003 du Canada
FCC Statement

17
Índice V
Introducción
Felicitaciones por adquirir el control remoto universal
GE. El control remoto universal GE es uno de los más
fáciles de usar hoy en día. Con el control remoto
universal GE, ¡el uso de varios controles remotos es
cosa del pasado! Su control remoto universal GE
controla varios dispositivos, incluidas las marcas más
populares de televisores, DVR, DVD, cable y satélite. El
control remoto universal GE es fácil de usar, fácil de
programar y le da control total: ¡con el simple toque
de sus dedos!
IMPORTANTE: GUARDE ESTE MANUAL Y LA LISTA DE
CÓDIGOS PARA CONSULTARLOS EN EL FUTURO
Introducción..................................................................................17
Configuración...............................................................................18
Para Instalar las Pilas........................................................18
Precauciones con las Pilas..............................................18
Ahorrador de Pilas ..............................................................18
Protección de Ahorros.......................................................18
Funciones de los Botones.......................................................19
Programación de su Control Remoto ...............................21
Entrada Directa de Códigos ...........................................21
Búsqueda Automática de Códigos .............................23
Función Favoritos:...............................................................24
Control de Aparatos Combinados...............................25
Uso de su Control Remoto ....................................................26
El uso de SHIFT.....................................................................26
Función de Volumen Principal .....................................26
Identificación de Códigos................................................28
Para Restablecer las Configuraciones
Predeterminadas.................................................................28
Solución de Problemas ...........................................................29
Garantía..........................................................................................30
Declaración de la FCC..............................................................31

18
Su control remoto universal necesita dos (2) pilas tamaño
AAA (no se incluyen). Se recomiendan pilas alcalinas.
Para Instalar las Pilas
1. En la parte posterior del control remoto, presione
sobrelasupercietexturizadaydeslicelatapadel
compartimiento de las pilas hacia abajo para poder
quitarla.
2. Inserte dos (2) pilas tamaño AAA, de manera que las
marcas (+) y (-) de las pilas coincidan con las marcas (+)
y (-) en el interior del compartimiento de las pilas.
Asegúrese de usar pilas nuevas.
3. Coloque la tapa del compartimiento de las pilas un
poco hacia abajo de la apertura y empuje hacia arriba
para que encaje en su lugar.
NOTA: Si su control remoto deja de funcionar
correctamente, reemplace las pilas por otras nuevas. El
control remoto conservará los códigos que ha programado
durante un máximo de 10 minutos después de retirar las
pilas.
Precauciones con las Pilas
• Nousepilasnuevasconpilasusadas.
• Nousepilasalcalinasconpilasestándar(carbono-zinc)
o con pilas recargables (Ni-Cd, Ni-MH, etc.).
• Siemprequitelasbateríasviejas,débilesodescargadas
con prontitud y recíclelas o deséchelas de acuerdo con
las regulaciones locales y nacionales.
Ahorrador de Pilas
Su control remoto se apaga automáticamente si los
botones se presionan durante más de 8 segundos. Esto le
ahorrará las pilas si el control remoto se permanece en un
lugar donde los botones quedan presionados (por ejemplo,
entre los cojines del sofá).
Protección de Ahorros
Usted tendrá hasta 10 minutos para cambiar las pilas
del control remoto sin perder los códigos que haya
programado. Sin embargo, no presione ningún botón hasta
que haya instalado las pilas nuevas en el control remoto.
Si presiona los botones sin haber instalado las pilas en el
control remoto, se perderán todos los códigos.
Configuración

19
Funciones de los Botones
ENTER
En algunos modelos de
televisores,seutiliza
después de la entrada
directa del número
del canal para cambiar
inmediatamente al canal
seleccionado.
MUTE Apaga el sonido
del televisor mientras que
la imagen continúa.
RECORD, PLAY, STOP,
REW, FF, PAUSE
TV, CBL, DVR, DVD,
SAT, AMP, AUX 1, AUX 2
Selecciona el dispositivo que se
va a controlar.
El indicador rojo se ilumina
cuando se presiona
cualquier botón.
MENU para mostrar el
menú en el televisor.
ARRIBA, ABAJO,
IZQUIERDA y DERECHA
Botones de navegación.
GUIDE Visualizaenpantalla
la guía de programas de
satélite o cable.
DVRT LIST Muestra la lista
de programas grabados.
ABCD (rojo, verde,
amarillo y azul)
Permiten tener acceso
a funciones adicionales
de DVR, receptor de
cable, satélite, Blu-ray,
etc... (las funciones
adicionales varían según
el dispositivo y la marca,
consulte el manual
del propietario del
dispositivo para obtener
más información).
TV CBL DVR DVD
SAT
AUDIO AUX2
AUX1
A B C D
MUTE
LAST
VOL
+
CH
OK
123
456
7 8 9
0
DVR LIST
MENU SHIFT
SETUPINFO
INPUT
GUIDE
EXIT

20
TV CBL DVR DVD
SAT
AUDIO AUX2
AUX1
A B C D
MUTE
LAST
VOL
+
CH
OK
123
456
7 8 9
0
DVR LIST
MENU SHIFT
SETUPINFO
INPUT
GUIDE
EXIT
OK Selecciona los elementos
del menú para el dispositivo
que está controlando
Funciones de los Botones, continuación
DOT:Seutilizapara
seleccionar los canales
digitales, por ejemplo: 2.3.
VOLUME ARRIBA/ABAJO
Cambia el nivel de volumen
del producto, normalmente
el del televisor.
El SHIFT es la función
alternativa de este botón
Utilice el botón SHIFT para
acceder el menú y la lista
DVR de su dispositivo. Para
entrar en el modo de SHIFT
Presione este botón una
vez.Parasalirdelmodode
SHIFT, pulse nuevamente el
botón SHIFT.
NÚMEROS
Introduzcanúmerospara
la selección directa de
canales. Algunos dispositivos
necesitan que se presione
ENTER después de la
selección del canal.
ON•OFF Enciende y
apaga dispositivos.
CHANNEL ARRIBA/ABAJO
Cambia los canales.
SETUPSeutilizapara
configurar el control
remoto y para la
función de búsqueda
de códigos.
INPUT Selecciona las entradas
de video de las fuentes de
visualizacióndisponibles.
Info (i)Visualizaen
pantalla la información
del canal, etc.
EXIT Sale de los menús en
pantalla y/o regresa a la
selección previa en pantalla.
LAST Regresa al canal
previamente seleccionado o
botón de repetición de DVD.