GEAppliances JVM2052 User manual

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Above the
Instructions Cooktop Oven
Model JVM2052
Read these instructions completely and carefully.
•IMPORTANT – Save these
instructions for local inspector’s use.
•IMPORTANT –Observe all
governing codes and ordinances.
•Note to Installer –Be sure to leave these
instructions with the Consumer.
BEFORE YOU BEGIN
•Note to Consumer – Keep these instructions
for future reference.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
49-40587
MFL57007101
09-08 JR

2
CONTENTS
General information
Important Safety Instructions ...................................... 3
Electrical Requirements .................................................. 3
Hood Exhaust ................................................................ 4-5
Damage—Shipment/Installation .................................. 6
Parts Included .................................................................. 6
Tools You Will Need.......................................................... 7
Mounting Space ................................................................ 7
Step-by-step installation guide
Prepare the Electrical Connections .............................. 8
Prepare the Venting System .......................................... 9
Prepare the Venting ................................................ 10-11
Before You Start .................................................. 10
Remove the Mounting Plate .............................. 10
Installation Types .......................................... 10-11
Room-Vented (recirculating)
Installation ..................................................10
Wall-Vented Installation ......................10-11
Roof-Vented Installation............................11
Prepare the Wall & Upper Cabinet ........................ 12-13
Measure and Tack/Tape up the Templates .... 12
Drill the Holes in the Wall and
Upper Cabinet................................................ 12-13
Install the Mounting Plate ...................................... 13-14
Wall Stud ........................................................ 13-14
Wall-Vented ........................................................ 14
Attach the Oven to the Wall ........................................ 15
Installation Instructions

This product requires a three-prong grounded outlet.
The installer must perform a ground continuity check
on the power outlet box before beginning the
installation to insure that the outlet box is properly
grounded. If not properly grounded, or if the outlet
box does not meet electrical requirements noted
(under ELECTRICAL REQUIREMENTS), a qualified
electrician should be employed to correct any deficiencies.
CAUTION:
For personal safety, remove
house fuse or open circuit
breaker before beginning
installation to avoid severe
or fatal shock injury.
CAUTION: For personal safety, the mounting
surface must be capable of supporting the cabinet load,
in addition to the added weight of this 63–85 pound
product, plus additional oven loads of up to 50 pounds
or a total weight of 113–135 pounds.
CAUTION: For personal safety, this product
cannot be installed in cabinet arrangements such as an island
or a peninsula. It must be mounted to BOTH a top cabinet
AND a wall.
NOTE: For easier installation and personal safety,
it is recommended that two people install this product.
IMPORTANT—PLEASE READ CAREFULLY.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLY GROUNDED TO AVOID SEVERE
OR FATAL SHOCK.
The power cord of this
appliance is equipped with
a three-prong (grounding)
plug which mates with
a standard three-prong
(grounding) wall receptacle
to minimize the possibility
of electric shock hazard
from this appliance.
You should have the wall receptacle and circuit checked
by a qualified electrician to make sure the receptacle is
properly grounded.
Where a standard two-prong wall receptacle is
encountered, it is very important to have it replaced
with a properly grounded three-prong wall receptacle,
installed by a qualified electrician.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR
REMOVE ANY OF THE PRONGS FROM THE POWER CORD.
DO NOT USE WITH AN EXTENSION CORD.
IMPORTANT SAFETY INSTRUCTIONS
3
ELECTRICAL
REQUIREMENTS
Product rating is 120 volts ACE, 60 Hertz, 14.5 amps
and 1.70 kilowatts. This product must be connected
to a supply circuit of the proper voltage and frequency.
Wire size must conform to the requirements of the National
Electrical Code or the prevailing local code for this kilowatt
rating. The power supply cord and plug should be brought
to a separate 15 to 20 ampere branch circuit single
grounded outlet. The outlet box should be located in the
cabinet above the oven. The outlet box and supply circuit
should be installed by a qualified electrician and conform
to the National Electrical Code or the prevailing local code.
Insure proper
ground exists
before use
Installation Instructions

4
HOOD EXHAUST
The following chart describes an example of one possible
ductwork installation.
NOTE: Read these next two pages only if you plan to vent your exhaust to the
outside. If you plan to recirculate the air back into the room, proceed to page 6.
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared
at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.
Installation Instructions
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH* x USED = LENGTH
Wall Cap 40 Ft. x (1) = 40 Ft.
3 Ft. Straight Duct 3 Ft. x (1) = 3 Ft.
(31⁄4" x 10" Rectangular)
90° Elbow 10 Ft. x (2) = 20 Ft.
Equivalent lengths of duct pieces are based on actual tests and
reflect requirements for good venting performance with any vent hood. Total Length = 63 Ft.
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH x USED = LENGTH
Roof Cap 24 Ft. x (1) = 24 Ft.
12 Ft. Straight Duct 12 Ft. x (1) = 12 Ft.
(6"Round)
Rectangular-to-Round 5 Ft. x (1) = 5 Ft.
Transition Adapter*
Equivalent lengths of duct pieces are based on actual tests and
reflect requirements for good venting performance with any vent hood. Total Length = 41 Ft.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
*IMPORTANT: If a rectangular-to-round transition adapter is used, the bottom corners of the damper will have
to be cut to fit, using the tin snips, in order to allow free movement of the damper.
The following chart describes an example of one possible
ductwork installation.

EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH x USED = LENGTH
Rectangular-to-Round 5 Ft. x ( ) = Ft.
Transition Adapter*
Wall Cap 40 Ft. x ( ) = Ft.
90° Elbow 10 Ft. x ( ) = Ft.
45° Elbow 5 Ft. x ( ) = Ft.
90° Elbow 25 Ft. x ( ) = Ft.
45° Elbow 5 Ft. x ( ) = Ft.
Roof Cap 24 Ft. x ( ) = Ft.
Straight Duct 6" Round or 1 Ft. x ( ) = Ft.
31⁄4" x 10" Rectangular
Total Ductwork = Ft.
Equivalent lengths of duct pieces are based on actual tests
and reflect requirements for good venting performance with
any vent hood.
* IMPORTANT::If a rectangular-to-round transition
Adapter is used, the bottom corners of the damper
will have to be cut to fit, using the tin snips, in order
to allow free movement of the damper .
NOTE: If you need to install ducts, note that the total duct
length of 31⁄4" x 10" rectangular or 6" diameter round duct
should not exceed 120 equivalent feet.
Outside ventilation requires a HOOD EXHAUST DUCT.
Read the following carefully.
NOTE: It is important that venting be installed using
the most direct route and with as few elbows as possible.
This ensures clear venting of exhaust and helps prevent
blockages. Also, make sure dampers swing freely
and nothing is blocking the ducts.
Exhaust connection:
The hood exhaust has been designed to mate with
a standard 31⁄4" x 10" rectangular duct.
If a round duct is required, a rectangular-to-round
transition Adapter must be used. Do not use less
than a 6" diameter duct.
Maximum duct length:
For satisfactory air movement, the total duct length
of 31⁄4" x 10" rectangular or 6" diameter round duct
should not exceed 120 equivalent feet.
Elbows, transitions, wall and roof caps, etc.,
present additional resistance to airflow and are equivalent
to a section of straight duct which is longer than their
actual physical size. When calculating the total duct
length, add the equivalent lengths of all transitions and
adapters plus the length of all straight duct sections.
The chart below shows you how to calculate total
equivalent ductwork length using the approximate
feet of equivalent length of some typical ducts.
5
Installation Instructions

PART QUANTITY
Upper Cabinet 1
Template
Rear Wall 1
Template
(3 pieces
mounting
plate only)
Installation 1
Instructions
Exhaust 1
Adapter
Damper 1
Power Cord 1
Clamp Bushing
(for the cord
hole in a metal
upper cabinet)
PART QUANTITY
Lag Screws (1⁄4" x 2") 4
(for wall stud holes)
Toggle Bolts (1⁄4" x 3") 4
(for drywall holes)
Spring Toggle Heads 4
(for toggle bolts)
Bolts 2
(for securing to
the upper cabinet)
Tapping Screws (1⁄8"x 1⁄2") 1 black
(for attaching the 2 bronze
damper duct connector)
Power Cord Clamp and 1
Dark-Colored Mounting
Screw (to hold
the power cord)
6
•If the unit is damaged in shipment, return
the unit to the store in which it was bought for
repair or replacement.
•If the unit is damaged by the customer, repair
or replacement is the responsibility of the customer.
•If the unit is damaged by the installer (if other
than the customer), repair or replacement must
be made by arrangement between customer
and installer.
DAMAGE – SHIPMENT/
INSTALLATION
PARTS INCLUDED
ADDITIONAL PARTS
Installation Instructions
PARTS INCLUDED
You will find the installation hardware contained
in a packet with the unit. Check to make sure you
have all these parts.
NOTE: Some extra parts are included.
NOTE: You need to install at least two lag screws
into a 2" x 4" stud and four anchor bolts into the wall.
Also, the mounting area must meet the 150 lbs. weight
requirement.
HARDWARE PACKET

7
MOUNTING SPACE
NOTES:
•The space between the cabinets must be 30" wide
and free of obstructions.
•If the space between the cabinets is greater
than 30", a Filler Panel Kit may be used to fill
in the gap between the oven and the cabinets.
Your Owner’s Manual contains the kit number
for your model.
•This oven is for installation over ranges up to
36" wide.
•If you are going to vent your oven to the outside,
see Hood Exhaust Section for exhaust duct
preparation.
•When installing the oven beneath smooth, flat
cabinets, be careful to follow the instructions
on the upper cabinet template for power cord
clearance.
•Maximum cabinet depth above and beside
the unit is 13".
•For models with top venting holes: Do not allow
cabinetry or other objects to block the airflow
of the vent.
Backsplash
66" or more
from the floor
to the top of
the oven
30"
2"
30"
min.
16-1⁄4"
Bottom edge of
cabinet needs to
be 30" or more
from the cooking
surface
Installation Instructions
NOTE: Maximum cabinet depth is 13".
TOOLS YOU WILL NEED
Phillips screwdriver Flat blade screwdriver
Pencil
Caulking gun
Plumb line
Ruler or tape measure
and straight edge Carpenter square
(optional)
Tin snips (for cutting
damper, if required) Electric drill with 3⁄8" and 3⁄4" wood
drill bits and 3⁄16" and 1⁄2" drill bits
Hammer (optional)
Stud finder or
Gloves
Saw (saber, hole or keyhole)
Duct and masking tape
Clear tape
(for taping the templates to the wall)
Scissors
(to cut template, if necessary)
Safety goggles

8
Grounded outlet
(inside cabinet)
Upper
cabinet
Installation Instructions
Power-supply-cord hole
You will cut the power-supply-cord hole (shown
below) later when you prepare the wall and upper
cabinet in Step 4.
NOTE: Do not use an extension cord. Keep the power
cord dry and do not pinch or crush it.
2
1 PREPARE THE ELECTRICAL
CONNECTIONS
WARNING: Avoid electrical shock!
This appliance must be grounded!
Locate the grounded electric outlet for this oven
in the cabinet above the oven, as shown at right.
NOTE: The outlet should be on a circuit dedicated
to the microwave oven (120V, 60 Hz., AC only) with
a 15 or 20A fused electrical supply.
IMPORTANT: If you do not have the proper wall
outlet, you MUST have one installed by a qualified
electrician.
WARNING: Improper grounding could
result in electric shock or other personal injury.
• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE
THE POWER SUPPLY CORD GROUNDING PRONG!
• This appliance MUST be grounded!
1

9
Installation Instructions
Wall Venting—If your oven is located on an outside
wall of your house, as shown below (3 1/4" x 10" duct
or 6" round duct.)
Room Venting—If your oven is located on an inside
wall of your house, as shown below.
NOTE: If you choose the rear exhaust method
(roof- or wall-venting), be sure there is enough
clearance within the wall for the exhaust duct.
REMEMBER AS YOU INSTALL THE VENTING: Keep
the length of the ductwork and the number of elbows
to a minimum to ventilate your oven efficiently. See
examples on page 5. Keep the size of the ductwork
the same. Do not install two elbows together. Use duct
tape to seal all joints in the duct system. Use caulking
to seal the exterior wall or roof opening around
the cap.
Oven
Cabinet
Through-the-wall
Oven
Cabinet
Wall venting
3 1/4" x 10" duct Wall cap
3 1/4" to round
duct transition
Elbow
Roof cap
6" min
diameter
round duct
Wall cap
2 PREPARE THE VENTING SYSTEM
NOTE: The ductwork you need for outside ventilation
is not included with your oven. The standard ductwork
fittings and length are shown on pages 4 and 5.
WARNING: This oven must be properly
vented.
You may vent your oven in one of three ways. Do NOT
vent into a wall cavity, an attic or an unused area.
Roof Venting—If your oven is located on an outside
wall near the roof, as shown below (3 1/4" x 10" duct
or 6" round duct).
Oven
Cabinet
Roof venting
3 1/4" to round
duct transition
Elbow
Roof cap
6" min
diameter
round duct
Wall cap
Through-the-roof
3 1/4" x 10" duct
Roof cap

10
Installation Instructions
3 PREPARE THE VENTING
WARNING:
• To avoid the risk of property damage, unplug the
microwave oven or disconnect power at the source
by removing the fuse or throwing the circuit breaker.
• To avoid the risk of personal injury, wear protective
gloves when handling the mounting plate.
• DO NOT PULL OR STRETCH THE BLOWER WIRING!
Pulling and stretching the blower wiring could result
in electrical shock.
NOTE: Your microwave oven is shipped with the blower
assembled for room venting. If you want wall-vented
or roof-vented installation, you must change the blower,
as detailed below.
A BEFORE YOU START
Remove any shipping materials and parts from
inside the microwave oven.
Cover the counter top or cooktop with a thick,
protective covering to protect it from damage
and dirt.
NOTE: If you have a free-standing range, disconnect
it, move it onto a piece of cardboard or hardboard
and pull it away from the wall. This allows you to
get closer to the upper cabinet and back wall for
easier measuring and drilling.
B REMOVE THE MOUNTING PLATE
Remove the mounting plate screw(s) (1 or 2 screws)
from the mounting plate as shown and discard.
1
2
1
A thick, protective
covering
Mounting plate Mounting plate
screw(s) (1 or 2
screws)
Control
panel
side
Mounting plate
Mounting
plate
screw(s)
(1 or 2
screws)
Control
panel
side
This plate will be used as the rear mounting plate.
(It will be used to locate and mark the mounting
holes on the rear wall.
Locate the exhaust adapter, grease filters and
hardware packet.
At this point, remove any adhesive tape (if there is
any), on the exhaust adapter, the grease filters and
the power supply cord.
C INSTALLATION TYPES
Room-Vented (recirculating) Installation:
This oven is shipped assembled for room venting.
Wall-Vented Installation:
Remove one blower unit mounting screw and one
or two blower plate screw(s). Remove the blower
plate from the cabinet.
Carefully lift the blower unit out of the microwave
oven.
Use side cutters or tin snips to cut and remove
knockouts “B” from back plate. Discard the
knockouts. Be careful not to distort the plate.
2
3
4
Back plate
Blower plate
Blower unit
mounting screw
(option)
Mounting screw
(option)
Blower plate
Blower unit
Parts “B”
Parts “B”
Knockouts Parts “B”
2
3
1

Installation Instructions
3 PREPARE THE VENTING (cont.)
C INSTALLATION TYPES (cont.)
Wall-Vented Installation (cont.):
Reassemble the blower wire.
Rotate the unit so that the exhaust ports face
the rear of the cabinet. When you insert the blower
unit, the blower wire must be as shown.
Place the blower unit back into the cabinet.
Check that the exhaust ports face toward
the rear of the cabinet.
Reattach the blower plate to the cabinet so the
exhaust ports and blower plate opening are aligned.
Attach with one blower unit mounting screw and
then one blower plate mounting screw.
4
Exhaust ports
Blower unit
Exhaust ports
Back plate
Blower unit
mounting screw
(option)
Blower plate
mounting screw
(option)
Blower plate
Blower unit
Blower unit exhaust ports
6
7
5
Roof-Vented Installation:
Remove one blower unit mounting screw and one
or two blower plate screw(s). Remove the blower
plate from the cabinet.
Use side cutter or tin snips to cut and remove
knockouts “A” from the blower plate. Discard
knockouts. Be careful not to distort the plate.
Carefully lift the blower unit out of the microwave
oven.
Rotate the blower unit 90° so the exhaust ports
face the top of the cabinet.
Reassemble the blower wire.
Place the blower unit back into the microwave oven.
Reattach the blower plate to the microwave oven.
Attach with the one blower unit mounting screw and
then the one or two blower plate mounting screw(s).
Attach the exhaust adapter to the blower plate
by sliding it into the Guide.
1
2
3
4
5
6
Blower plate
Knockouts ”A“
Blower unit
Blower unit
Blower plate
Blower unit
mounting
screw (option)
Blower plate
mounting
screw (option)
8
7
Exhaust adapter
Back of oven
Back plate
Blower unit
mounting screw
(option)
Blower plate
mounting screw
(option)
Blower plate
Blower unit
Parts “B”
11

12
Installation Instructions
Center the mounting plate by lining up the plumb
line on the wall with the center line on the mounting
plate. Make sure the minimum width is 30 inches
and that the top of the mounting plate is located
a minimum of 30 inches above the cooking surface.
NOTE: If the cabinets are not plumb, adjust the
mounting plate to the cabinets. If the front edge
of the cabinet is lower than the back edge, adjust
the mounting plate to be level with the cabinet front.
Measure the bottom of the upper cabinet frame.
Trim the edges A, B and C on the upper cabinet
template so that the template will fit on the bottom
of the upper cabinet. If the upper cabinet has a
recessed frame, trim the template so it fits inside
the recessed area. Align the center line of the upper
cabinet template with the center line of the
mounting plate, then securely tape or tack
the upper cabinet template in place.
WARNING: To avoid the risk of personal
injury, electrical shock or death:
• Note where electrical outlets and electrical wires
are before you drill into the wall.
• Locate and disconnect power to any electrical
circuits that could be affected by installing this oven.
WARNING: To avoid the risk of personal
injury, electrical shock or death, cover the edge of
the power supply cord hole with the power supply
cord bushing.
Drill the Holes in the Wall and Upper Cabinet
Drill holes on the circles. If there is a stud, drill a 3/16"
hole for lag screws. If there is no stud, drill a 3/4" hole
for toggle screws. Make sure to use at least 1 lag
screw in a stud and 4 toggle screws in the drywall
or the plaster.
1
5
4
Mounting plate
Upper cabinet template
Mounting plate
Upper cabinet template
(3 pieces mounting plate)
(1 piece mounting plate)
4 PREPARE THE WALL AND UPPER
CABINET
WARNING: To avoid personal injury or
property damage, do not attempt to install this
microwave oven if you cannot find a wall stud.
Measure and Tack/Tape Up the Templates
Using a plumb line and measuring tape, find
and mark the vertical center line on the back wall,
as shown.
Find and mark one or two points where the studs
are on the wall. Then measure and mark the stud
locations. If you cannot find any wall stud, consult
a local building contractor.
CAUTION: DO NOT ATTEMPT TO INSTALL THE
MICROWAVE OVEN IF YOU CANNOT FIND A WALL STUD.
Line up the plumb line on the wall with the center
line on the mounting plate.
NOTE: Be sure the minimum width is 30 inches and
the distance from the top of the wall template to the
range or counter top is at least 30 inches.
3
2
1

13
Installation Instructions
4 PREPARE THE WALL AND UPPER
CABINET (cont.)
Drill the Holes in the Wall and Upper Cabinet (cont.)
Drill a 3/8" hole at points Jand Kon the upper cabinet
template.
NOTE: If the bottom of the upper cabinet is recessed
3/4" or more, you will need 2" x 2" filler blocks (not
included) to provide additional support for the bolts.
• Mark the center of each filler block and drill a 3/8"
diameter hole at the marks.
• Align filler blocks over the two openings in the top of
the microwave oven cabinet and attach to the cabinet
with masking tape.
Cut or drill a 2" diameter hole at the area marked M.
Power supply cord hole on the upper cabinet template.
If the upper cabinet is metal, you will need to cover the
edge of the hole with the power supply cord bushing
(supplied) to prevent damage to the cord from the rough
metal edge.
Cut out the venting areas (with the saber saw):
•Roof-Vented: Cut out the shaded area marked L
on the upper cabinet template.
•Wall-Vented: Tape the rear wall template to the rear
wall, lining up with the holes previously drilled for holes
Aand Bin the plate. Cut out the shaded area marked F
on the REAR WALL TEMPLATE.
•Room-Vented: Go to STEP 5, INSTALL THE MOUNTING
PLATE, on page 14.
Complete whichever venting system you have chosen.
Use caulking compound to seal the exterior wall or roof
opening around the wall cap or roof cap.
3
5
2
4
Cabinet bottom shelf
Filler block
Cabinet front Filler block
5 INSTALL THE MOUNTING PLATE
The Oven Must Be Connected to at Least One
Wall Stud.
Draw a vertical line on the wall at the center of
the 30 wide space. Use the mounting plate as the
template for the rear wall. Place the mounting plate
on the wall, making sure that the tabs are against
the bottom of the cabinet. Line up the notch and
center line on the mounting plate to the center line
on the wall.
While holding the mounting plate with one hand,
draw circles on the wall at holes A, B, Cand D. Four
holes must be used for mounting. If the holes are not
used, the installation will not be secure. Installer must
use these holes for proper installation. Use toggle
bolts through these holes unless one of them lines
up with a stud. Use a wood screw for studs.
NOTE: Draw a fifth circle inside area E, through one
of the bottom holes to match the location of a stud.
For wall-vented: The oven requires a rear wall cutout
opening for the rear wall duct and the exhaust
adapter must be attached to the mounting plate.
See the next page on how to prepare the rear wall
cutout opening and the exhaust adapter/mounting
plate for wall-vented.
Drill holes on the circles. If there is a stud, drill a 3/16"
hole for lag screws. If there is no stud, drill a 5/8" hole
for toggle bolts. Make sure to use at least 1 lag screw
in a stud, and 4 toggle bolts in the drywall or the
plaster.
Attach the plate to the wall. To use spring toggle
headbolts: Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate and replace
the spring toggle head to 3/4" past the bolt ends.
Insert the spring toggle head into the holes in the
wall to mount the plate. You may pull forward on
the plate to help in tightening the toggle bolts.
Tighten all bolts.
1
2
3
4
Bolt end
Toggle wings
Toggle bolt
Wall
Toggle bolt
Space more than wall thickness

14
Installation Instructions
Minimum
66" from
the floor For wall-
vented only
3/16" Hole on studs
5/8" hole on drywall only
Draw lines
on studs
Mounting plate Draw center line
Center line
Support tab Support tab
A
D
B
E
5 INSTALL THE MOUNTING
PLATE (cont.)
For Wall-Vented
• Make the box cutout for the rear wall duct.
1 piece mounting plate:
Using a pencil, put dots through slots Fand G, and
through holes Hand I. Remove the mounting plate
and draw lines extending through the points. This will
give the location and size of the box cutout for the
rear wall duct.
3 pieces mounting plate:
Use the wall template to determine the location and
size of the box cutout for the rear wall duct.
• Attach the exhaust adapter to the rear mounting
plate (backplate) wall side. Push in securely until it is
past the top locking tabs and in the lower locking
tabs. Take care to assure the damper hinge is
installed so that it is at the top and that the damper
swings freely.
•Before using the screws to attach the plate to
the wall: Carefully guide the exhaust adapter, now
attached to the mounting plate, into the house duct.
This will assure proper alignment for installation.
• Return to step 5, item 3 to continue. After completing
the installation of the mounting plate, again check
the rear damper for free movement to assure it will
operate properly.
Exhaust adapter
Slide
exhaust
adapter into
guides on
rear panel.
Damper
(hinge side up)
Mounting plate
(1 piece mounting
plate)
Back plate 1 piece
mounting plate
(3 pieces
mounting plate)
Locking tabs
Guide
Guide

15
Installation Instructions
6 ATTACH THE OVEN TO THE WALL
WARNING:
To avoid the risk of personal injury or property damage,
you will need two people to install this microwave oven.
Carefully lift the microwave oven and hang it on
the support tabs at the bottom of the mounting
plate. Reaching through the upper cabinet, thread
the power supply cord through the power supply
cord hole in the bottom of the upper cabinet.
Rotate the microwave
oven upward so the
top of oven is against
the bottom of the
upper cabinet or
cabinet frame.
Then insert a bolt
down through each hole in the upper cabinet
bottom. Tighten the bolts until the gap between
the upper cabinet and the microwave oven
is closed.
1
Power cord
Power cord hole
If wall-vented or room-vented installation is used,
go to Step 7.
Roof venting installation: Install ductwork through
the vent opening in the upper cabinet. Complete
the venting system through the roof according to
the method needed. See “Prepare The Venting
System”, STEP 2. Use a caulking gun to seal the
exterior roof opening around the exhaust cap.
See the Roof-Venting illustration on page 9.
Use the power supply cord clamp to bundle the
power supply cord. Install the power supply cord
clamp, using a screw as shown, to the inside
of the cabinet.
Grasp the filter screen with one hand holding the
ring and the other hand holding the opposite end.
Insert the end of the filter screen without the ring
into the opening and slide toward the side of the
microwave oven. Insert the ring end of the filter
screen into the opening and slide the entire screen
toward the center of the microwave oven until the
screen is securely in position. Repeat for the other
filter screen.
Plug in the power supply cord.
Read your Owner’s Manual, then check
the operation of your microwave oven.
2
3
4
5
6
Damper
7
8
9
Minimum
66" from
the floor
For wall-vented
only
3/16" Hole on studs
5/8" Hole on drywall only
Draw lines
on studs
Mounting
plate
Draw center line
Center line
Support tab Support tab
A
D
B
E
A
B
C
D
C
Duct Power
supply
cord
clamp

Printed in China