Gecko in.clear 0605-500002 User manual

In.Clear™ Model No. 0605-500002
Automatic Bromine Generator
For Spa Sanitizing
DOMESTIC
A maximum of 2000 Litres of water can be treated with one In.Clear Automatic Bromine
Generator unit.
Maximum output of Hypobromus Acid equivalent to 0.04 kg of free available bromine per day.
A range of 3 – 5 ppm of free available bromine must be maintained.
READ THE LABEL AND OPERATION/INSTALLATION MANUAL BEFORE USING THIS
DEVICE
KEEP OUT OF REACH OF CHILDREN
REGISTRATION No. 29628 PEST CONTROL PRODUCT ACT
WARNING:
Operating the In.Clear Automatic Bro mine Generator without water fow through the cell can
cause a build up of fammable gases which can result in FIRE or EXPLOSION.
NOTICE TO USER:
This pest control product is to be used only in accordance with the instructions shown on the
label. Any use not in accorda nce with these in structions is an offence under the Pest Control
Products Act. The u ser assumes the risk to pe rsons or property arising from the u se of this
product.
Tested and Listed to standards
ANSI/UL – UL 1081, UL 1563
CAN/CSA - C22.2 No. 108-1
Gecko Alliance Group Inc.
450, Des Canetons, Québec (Québec)
Canada G2E 5W6
800-784-3256 ext. 350
418-872-4411 ext. 350
2011-5850
2012-10-25

Page2
In.Clear™ Model No. 0605-500002
Automatic Bromine Generator
For Spa Sanitizing
DOMESTIC
A maximum of 2000 Litres of water can be treated with one In.Clear Automatic Bromine
Generator unit.
Maximum output of Hypobromus Acid equivalent to 0.04 kg of free available bromine per day.
A range of 3 – 5 ppm of free available bromine must be maintained.
READ THE LABEL AND OPERATION/INSTALLATION MANUAL BEFORE USING THIS
DEVICE
KEEP OUT OF REACH OF CHILDREN
REGISTRATION No. 29628 PEST CONTROL PRODUCT ACT
WARNING:
Operating the In.Clear Automatic Bro mine Generator without water fow through the cell can
cause a build up of fammable gases which can result in FIRE or EXPLOSION.
NOTICE TO USER:
This pest control product is to be used only in accordance with the instructions shown on the
label. Any use not in accorda nce with these in structions is an offence under the Pest Control
Products Act. The u ser assumes the risk to pe rsons or property arising from the u se of this
product.
Gecko Alliance Group Inc.
450, Des Canetons, Québec (Québec)
Canada G2E 5W6
800-784-3256 ext. 350
418-872-4411 ext. 350
CONNECT ONLY TO A CIRCUIT PROTECTED BY A CLASS A, GROUND FAULT
CIRCUIT INTERRUPTER. (GFCI)
SUITABLE FOR INDOOR USE ONLY OR WHEN INSTALLED UNDER A
WEATHERPROOF SPA SKIRT.
THIS UNIT MUST NOT BE INSTALLED IN PROXIMITY TO HIGHLY FLAMMABLE
MATERIALS.
CSA ENCLOSURE NUMBER 2.

Page3
In.Clear™ Model No. 0605-500002
Automatic Bromine Generator
For Spa Sanitizing
DOMESTIC
A maximum of 2000 Litres of water can be treated with one In.Clear Automatic Bromine Generator unit.
Maximum output of Hypobromus Acid equivalent to 0.04 kg of free available bromine per day.
A range of 3 – 5 ppm of free available bromine must be maintained.
READ THE LABEL AND OPERATION/INSTALLATION MANUAL BEFORE USING THIS DEVICE
KEEP OUT OF REACH OF CHILDREN
REGISTRATION No. 29628 PEST CONTROL PRODUCT ACT
WARNING: Operating the In.Clear Automatic Bromine Generator without water fow through the cell can cause a buildup
of fammable gases which can result in FIRE or EXPLOSION.
NOTICE TO USER:
This pest control product is to be used only in accordance with the instructions shown on the label. Any u se not in accordance with
these instructions is an offence under the Pest Control Products Act. The user assumes the risk to persons or property arising from
the use of this product.
Gecko Alliance Group Inc., 450, Des Canetons, Québec (Québec), Canada G2E 5W6
800-784-3256 ext. 350, 418-872-4411 ext. 350

Page4
table of contents
Table of contents
In.Clear™
introduction ...........................................................................................5
warnings ...............................................................................................6
bromine benefts - how In.Clear™ works ..............................................9
keypad installation ..............................................................................10
- installing the in.k200™ ....................................................................10
- skirt mount installation .....................................................................11
- connecting the in.k200™ to In.Clear™ .............................................12
In.Clear™ installation ...........................................................................13
operating modes .................................................................................16
getting started (see video) ..................................................................18
keypad operations ...............................................................................23
troubleshooting ....................................................................................27
F.A.Q....................................................................................................30
glossary ...............................................................................................31
cell cleaning..........................................................................................33
specifcations .......................................................................................35

Page5
introduction
In.Clear™
Water sanitation systems for spas
With its waterproof enclosure, its sturdy design, the new In.Clear™ is the most efficient water sanitation system offered to
the spa and hot tub industry today.
In.Clear™ is a system that generates and releases bromine into the spa water to rapidly control and destroy any
microbiological contaminants such as waterborne bacteria, algaes, body chemicals, organic matter given off by spa
bathers and other organisms known to be linked to recreational water illnesses.
The new In.Clear™ system eliminates the need to add extra chemicals in the water to destroy unsightly pollutants and
achieves impeccable results. The In.Clear™ system does not produce any offensive odors, it rather reduces eye irritation
and it's easy to handle, making the In.Clear™ a good choice for hot tub sanitation.
Spas using the new In.Clear™ system need very little maintenance, and In.Clear™ can be easily installed on new or
existing spas.

Page6
Warnings
Warnings! Important safety instructions
• For Canada, In.Clear™ must only be used with sodium bromide (such as BromiCharge™) scheduled or registered under
the Pest Control Product Act. For USA, the source of sodium bromide (such as BromiCharge™) must be registered
under EPA.
• Read and follow this manual carefully and make sure to save it for later.
• This manual contains important information on In.Clear's installation, use and safety recommendations. It is your
responsibility to install and use your In.Clear™ unit safely.
• In.Clear™ must be connected to a circuit protected by a ground fault interrupter device (GFCI) in North America or
residual current device (RCD) having a rated residual operating current not exceeding 30 mA in Europe.
• Make sure all electrical power is off before installing the In.Clear™ unit. If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent or similarly qualifed persons in order to avoid a hazard.
• Use only an electrical cord in good condition to power In.Clear™.
• Always clean or replace your flter cartridges at regular intervals, otherwise part of the bromine generated by In.Clear™
will only serve to oxidize the dirt accumulated in the flter.
• Do NOT add any other sanitation chemicals in the spa other than registered sodium bromide (such as BromiCharge™)
• Operating the In.Clear™ at reduced sodium bromide (such as BromiCharge™) levels will shorten the life of the cell.
• Do not open the In.Clear™ unit; there are no serviceable parts inside.
• Disposal of the product: the In.Clear™ unit must be done separately in accordance with the local waste disposal
legislation in force.

Page7

Page8
Warnings
Warnings!
• This unit is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning use of the unit by a person responsible
for their safety.
• To reduce the risk of injury, do not allow children to operate this device.
• In.Clear™ may not be suitable for in ground spas, it may affect some materials used in their construction.
• The unit must be installed in a location that is inaccessi ble to a person in the bath or spa and must be located or fxed so
that it cannot fall into the bath or spa.
• The unit is not intended for in-ground spas as it may affect certain materials used in the spa’s construction.
The unit is not designed to be submersed but may be installed underneath the waterproof skirt of the spa.
• A means for disconnection must be incorporated in the fxed wiring in accordance with the wiring rules.
• Do not add chemical products for pool or spa directly into the skimmer. This may damage the cell.
• It is the responsibility of the user to test the spa water regularly to ensure that adequate amounts of bromine are
generated to achieve proper sanitizer levels.
• Heavy spa usage may require higher bromine output to maintain proper quantity of free available bromine.
• The expected life time of the electrodes is 30 000 hours when used in normal operating conditions.

Page9
Warnings
Warnings!
• • Maintaining overly high sodium bromide and bromine levels above recommended range can contribute to corrosion of
spa equipment and may damage components of the spa.
• The cell is installed after the heater in the circulation pump line.
o Do NOT use any ozone or UV sanitizer.
• Check the expiry date of the test kit as test results may be inaccurate if used after that date.
• Follow all aspects of the local and Na tional Electrical Code(s) when installi ng the In.Clear™ Automatic Bromine
Generator.
• People with a medical condition should consult a physician before entering spa water.
• Women who are pregnant should NOT enter the spa.
• Maximum spa water usage temperature is 40°C. Bathing in spa water at 40°C should not exceed 15 minutes.
• For proper sanitation, spa must be completely drained periodically. The number of days between COMPLETE SPA
DRAINAGE is equal to the volume of the spa water in liters, divided by 10 times the maximum number of daily spa users.
Refll spa with water and repeat DIRECTION FOR USE of the device.
- For a 1500 liters (400 US gallons) spa used by 2 adults twice a week: 1500 / (10 x (4/7)) = 262 days or 8 months
• In.Clear™ is meant for a covered spa NOT swimming pools.
• Users should always shower before entering a spa.

Page10

Page11
bromine benefits
How In.Clear™ works!
When sodium bromide (such as BromiCharge™) is added to the water, it separates into sodium ions and bromide ions. As
the water passes through the In.Clear™ bromine generator, a low-voltage source supplies a current that electrolytically
reduces the bromine ions into bromine which reacts with the water molecules to form free bromine. Bromine is known to
be a highly effective bactericide and algaecide. This process releases bromide ions back into the water for continuous
recycling until the spa is emptied. It is important to note that the amount of bromine needed will vary in direct proportion to
the number of bathers in the spa (bather load).
Effects of bromine
• Bromine destroys waterborne bacteria.
• Bromine destroys algae in water (e.g. Black, Green, Mustard).
• Bromine swiftly eliminates the presence of organic matter left behind by spa users (oil, sweat, dead skin cells).
• Because bromine doesn’t contain calcium, it can be used to sanitize hard water without increasing the calcium hardness.
Bromine in a spa!
Bacteria require a certain period of time before forming into micro colonies and becoming attached to a surface. Rapid
elimination of bacteria is a key element in the proper maintenance of the spa water. In.Clear™ achieves this while
oxidizing odors and reducing eye irritation. In.Clear™ enhances the clarity and quality of spa water. For bathers this
translates into a more enjoyable warm water therapy experience.

Page12
keypad installation
Installing the in.k200™
The keypad should be installed directly onto the spa (or very close to it) so that it is easily accessible to the user.
• To install the in.k200™, drill two 25 mm (1”) diameter holes at 67 mm (2 5/8”) from center to center as illustrated.
• Cut out the material between the two holes (see illustration).
• Clean the installation surface and peel the adhesive gasket from the back of the keypad.
• Insert keypad and align it correctly, then ensure it's properly glued by gently pressing evenly on the entire surface.
If the keypad is equipped with an optional holder plate remove the two wing nuts in the back of the keypad and remove the
mounting bracket.
Insert the keypad into opening you have cut out. Put the mounting bracket and the wing nuts back on their respective bolts
and fx the keypad securely in place (see illustration above).
Note: It is the installer’s responsibility to ensure that no obstructions (cables, piping, etc.) are present below the deck at the
drill hole location.
Note: If the installation location is not perfectly even (e.g. wood surface) , make a silicone joint between the installati on
location and the back of the unit to ensure a proper seal around it.
Figure: in.k200

Page13
keypad installation
Skirt mount installation
For a skirt mount installation the keypad should be installed directly on a spa panel so that it is easily accessible to the
user. Insure that the keypad control is located accordingly.
Drill from the finished side of the spa to prevent chipping of the surface. Start by pilot drilling the hole centers using a 3
mm (1/8”) drill bit. Using the appropriate hole saw slowly drill two 25 mm (1”) diameter holes at 67 mm (2 5/8”) from center
to center as illustrated.
Cut out the material between the two holes (see illustration).
Figure: Skirt mount installation
Clean the installation surface and route the keypad cable from the wall cutout to the In.Clear™ unit.
Peel the adhesive gasket from the back of the keypad, insert it in the cutout and align it correctly, then ensure it's properly
glued by gently pressing evenly on the entire surface.
If the keypad is equipped with an optiona l holder plate, remove the two wing nuts in the back of the keypad and remove
the holder plate. Insert the keypad into the opening you have cut out. Put the wing nuts back on their respective bolts an d
fix the keypad securely in place (see illustration above).
Note: It is the installer’s responsibility to ensure that no obstructions (cables, piping, etc.) are present below the deck at the
drill hole location.
Note: If the installation location is not perfectly even (e.g. wood surface), make a silicone joint between the installation
location and the back of the unit to ensure a proper seal around it.

Page14
keypad installation
Connecting in.k200™ main keypad to In.Clear™
The in.k200™ comes with a 3.3 m (10 ft) cable and an in.link connector.
To connect the in.k200™, simply insert its in.link connector into the appropriate keypad connector "C" (as illustrated).
Figure: Connecting the in.K200 main keypad to In.Clear

Page15
In.Clear™installation
In.Clear™ installation scheme with circulation pump
Figure A: In.Clear installation scheme with circulation pump
Water jet circulation pump 11 to 150 liters/min (3 to 40 US GPM).
Note: The pressure in the piping must be at least 3 PSI when water is circulating.

Page16
In.Clear™installation
Installation
In.Clear™ unit must be installed before the spa is flled with water.
The In.Clear™ unit must be installed on the pressure side of the circulation pump (refer to Fig.A for details). It should be
installed after the heater.
If the spa is equipped with a circulating pump, refer to Figure A.
The In.Clear™ system can be installed in an upright position or horizontally.
Installing valves on both sides of the In.Clear™ may help for maintenance purposes.
!!! We do not recommend to install the In.Clear™ on a spa equi pped with a dual-speed pump. The In.Clear works only
when the pump is running, therefore t he dual speed pump will require to run around 8-10 hours to have optimum bromine
production. Running a large pump for that period of time may be difficult in warm weather, without overheating the spa.
!!! The In.Clear™ system should be installed at the pressure side on a 11,4 to 151 liters/min (3 to 40 US GPM) fow line.
It's important not to exceed 151 liters/min (40 US GPM) to prevent excessive electrode wear and damage to the In.Clear™
unit.
!!! For all types of installation make sure there’s no pinch in the plumbing and that water fows.
! !!Water fow must run from bottom to top.
!!! If water fow is as low as 11.4 liters/min (3 US GPM) and In.Clear is to be installed horizontally, an air gap may appear
at the top which may decrease the performance of the unit. In that case, raise the outlet about 1 inch above the water inlet
level. The exact location and the method of installation of the In.Clear™ may vary depending on the plumbing design of

Page17
the spa.

Page18
In.Clear™installation
Installation
For an optimal connection to spa plumbing , please note that we recommend the comp ression fittings & nuts as illustrated
below.
(figure)
Use adapters to connect the In.Clear™ system to 3/4" tubing or directly to 2" tubing.
Slide the two plastic union nuts over the In.Clear™ unit's threaded ends and tighten the nuts.
!!! Hand tighten! Do not use tools!
!!! In.Clear™ must be protected by the same ground fault interrupter (GFCI) circuit as the spa system
!!! A blinking “AC” message on the keypad means that the input signal is not 240 VAC, and may likely be 120 VAC.
Please check connection.
Connect the in.k200™ keypad to the unit (see keypad installation section of this manual for more details).

Page19
operation modes
Installation
The In.Clear™ system operates in two modes:
Maintenance Mode and Boost Mode
Maintenance Mode:
The primary function of the Maintenance Mode is to keep the bromine bank levels at a stable and acceptable range when
the spa is not being used. Maintenance Mode is the “everyday” mode and is automatically ON when the system is
activated.
To maintain the residual bromine level within a normal range, the user has to set the Maintenance Level of the In.Clear™
system by adjusting the value of the Maintenance Mode. The higher the value, the more bromine generated. A bromine
level between 3 and 5 PPM must be maintained.
The goal is to maintain bromine at a cons tant level between the limits of 3-5 ppm when the spa is not being used or left
unused for an extended peri od of time. Once the proper ma intenance level is determined, keep the same s etting unless
the spa usage changes.
!!! Finding the right bromine generation level is a crucial step for the In.Clear™ system to be stable and effective. Refer to
section“6 -Determining the proper bromine generation Maintenance Level for my spa” for more information.
!!! The spa fltration should be set at a minimum of 8hrs per day. It is important to note that the In.Clear™ system can
ONLY generate bromine when the water is circulating. If you are having problems maintaining a stable level of
bromine, or determining the proper maintenance level for your spa, you may have to increase the daily fltering time.
Longer fltration produces a more steady level of bromine.

Page20
operation modes
Boost Mode:
The Boost Mode should be activated every time you use your spa. Boost Mode increases the bromine generation rate to
attack pollutants in the water and helps rebuild the necessary residual bromine in the water after each use of the spa.
Pollutants are introduced to the water by the bathers causing the bromine levels to decrease. Activating the Boost Mode
when you enter the spa will prevent inadequate bromine levels and will regenerate your bromine to the proper residual
level.
Finding the right Boost level is another crucial step for the In.Clear™ system to be stable and effective. Refer to section “7
- Determining the boost mode level for my spa”.
!!! If water quality is not good after use, only the Boost level should be adjusted, not the Maintenance level.