Gembird EE5-U2-3 User manual

External USB v.2.0 enclosure for 5.25" devices
EE5-U2-3 external USB 2.0 enclosure for
5.25" devices

External USB v.2.0 enclosure for 5.25" devices
Disclaimer
•We spared no efforts to make sure that the information in this manual is correct and
complete. owever no liability is accepted for any errors or omissions. Gembird
Electronics reserves the right to change the specifications of the hardware and
software described in this manual without prior notice.
•No part of this manual may be reproduced, transmitted or translated in any language
in any form, by any means, without the prior written permission of Gembird
Electronics Ltd.
•Gembird Electronics makes no warranties for damages resulting from corrupted or lost
data due to a mistaken operation or malfunction of the product, the software,
personal computers or peripheral devices.
Gembird® is a registered trademark of Gembird Europe.
Other names or products not mentioned above may be registered trademarks or
trademarks of their respective owners.
Copyright © 1997-2006 Gembird Electronics Ltd. All rights reserved.

External USB v.2.0 enclosure for 5.25" devices
Introduction
Thank you for buying our external USB 2.0 enclosure for 5.25"
devices! This manual will help you install it properly.
Features
•Fully compatible with USB 2.0 and USB 1.1 interfaces
•Suitable to all 3,5" hard disk drives as well as 5.25" devices
such as DVD-RW drives
•ot-swap, Plug-and-Play
•Power switch
•Aluminum case provides the best heat dissipation and hard
disk/DVD-drive protection
EE5-U2-3 User Manual

External USB v.2.0 enclosure for 5.25" devices
Specifications
•Up to 480Mbit/sec data transfer rate
•USB 2.0/IDE compliant: integrated IDE transceiver, high
speed (480Mbit/sec) and full speed (12Mbit/sec)
•Self-powered from USB
•Supports ATA PIO modes 0-4. ATA interface mode is
selected automatically
•Supports UDMA modes 0-4
•Supports 48-bit LBA (large DDs)
System requirements
•Personal computer equipped with USB port running
Windows 98/ME/2000/XP or Macintosh
•No driver is required with the exception of Windows 98

External USB v.2.0 enclosure for 5.25" devices
Hardware installation
•Connect your hard disk to the USB DD case and secure it
with the screws provided
•Connect the enclosure to any standard USB port on
PC/notebook with the USB cable provided.

External USB v.2.0 enclosure for 5.25" devices
Driver installation under Windows 98SE
After USB DD enclosure is connected, Windows 98 should
detect the new hardware and display "Found New
ardware…" wizard. When prompted, insert the CD provided
and let the system search for the correct driver, if necessary
specify \USB DD-CL811 USB DD_PL2506 in the search path.
If hardware is not detected by OS, follow these steps:
•Click "Start-Settings-Control Panel"
•Double click "Add New ardware" and then click "Next"
twice
•Select "No, the device isn't in the list" and click "Next"
•Select "No, I want to select the hardware from a list" and
click "Next"
•Select "Other devices" and click "Next"
•Click " ave Disk"
•Specify driver location, or click "Browse" to search for

External USB v.2.0 enclosure for 5.25" devices
driver location and select \USB DD-PL-2506 folder from
the CD provided and then click "OK"
•Click "OK" again
•Click "Next" twice, f ile copying will start
•Click "Finish", now the USB ard Disk Drive should appear
in My Computer or Windows Explorer. If it does not appear,
please, restart the computer.
Driver installation under Windows ME/ 000/XP
Under Windows ME/2000/XP, the system will f ind and setup the
"USB Mass Storage Device" automatically.
Congratulation, you can enjoy this product now!

External USB v.2.0 enclosure for 5.25" devices
Hard Disk Partitioning and Formatting
If there is no USB hard disk drive appeared in My Computer or
Windows Explorer after the above-mentioned procedures, you
may need to perform disk Partitioning and/or Formatting.
Windows 98/ME:
•Go to DOS prompt
•Run "FDISK" and perform the partitioning as you need.
Please note, you may need to delete the old partition f irst
if your hard disk was partitioned using other partitioning
utilities
•Run "FORMAT" to format the DD.
Windows 000/XP:
•Right click "My Computer" and then select "Manage"
•Go to "Disk Management"
•Perform Partitioning and formatting. Please refer to your
OS manual for details of how to use "Disk Management"

External USB v.2.0 enclosure for 5.25" devices
Warning: Before you disconnect the EE5-U2-3 from your system,
you should always perform the following procedure:
•Click the icon with your right mouse button
•Choose "Safely remove hardware" from the popup menu
•After the conf irmation the message "Storage device can
now be safely removed from the system" will appear.
Only now you can disconnect the EE5-U2-3 from the computer!
Troubleshooting
If all correct procedures have been followed and there is still no
USB ard Disk detected, you may need to access computer BIOS
and enable USB Devices. For details of how to access BIOS and
enable/disable devices, refer to your computer hardware manual.