Gembird NSW-R4 User manual

USER MANUAL
HANDBUCH
HANDLEIDING
MANUEL DESCRIPTIF
РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ
КЕРІВНИЦТВО КОРИСТУВАЧА
WIRELESS BROADBAND ROUTER, 300 M
WLAN BREITBAND ROUTER, 300 M
DRAADLOZE BREEDBAND ROUTER, 300M
ROUTEUR SANS FIL, 300M
БЕСПРОВОДНОЙ МАРШРУТИЗАТОР, СКОРОСТЬ ДО 300 МБИТ/С
БЕЗДРОТОВИЙ МАРШРУТИЗАТОР, ШВИДКІСТЬ ДО 300 МБІТ / С
NSW-R4

2
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Features
Wireless 300M router with 4-port 10/100Mbps LAN switch and 802.11n access point
Supports all IEEE802.11b/g/n WiFi standards
Up to 300 Mbps data transfer rate via the wireless 802.11n protocol
Built-in DHCP server automatically assigns and manages all IP addresses within your
LAN
Advanced firewall, 64/128-bit WEP encryption and WPA-PSK, WPA2-PSK security
Supports Wi-Fi Protected Setup ( WPS ) with reset button
Supports MAC/IP filtering and URL blocking (family filter)
Easy to use Web-interface for all router management options
Specifications
Supported standards: IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE
802.3u, CSMA/CA,CSMA/CD, TCP/IP, DHCP, ICMP, NAT, PPPoE, PPTP
Ports: - LAN: 4 x 10/100M Auto MDI/MDIX RJ45 ports
WAN: 1 x 10/100M Auto MDI/MDIX RJ45 port
Frequency band 2.4 ~ 2.4835GHz
Channels: 1 ~ 11 (US, Canada), 1 ~ 13 (Europe)
Supports Virtual Server and DMZ
Supports DDNS (DynDNS, TZO) and QoS
Data transfer rates: max 300 Mbps (11n), 54 Mbps (11g), 11 Mbps (11b)
Encryption standards: WPS, WPA, WPA2, WPA2/WPA Mixed
Antenna: 2 x 3 Dbi omni-directional antenna
RF power: 20 dBm (max)
Transmission distance: indoors up to 120 m, outdoors up to 360 m (distance is
dependent of environmental conditions, obstructions, walls, ceilings, etc)
Dimensions: 153 x 100 x 30 mm (W x D x H)
Operating temperature: 0 ~ 40 °C
Storage temperature: -40 ~ 70 °C
Operating humidity: 10 ~ 90 % non-condensing;
Storage humidity: 5 ~ 95 % non-condensing

3
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
1. Wireless router overview
1.1 Front panel (LED indicators)
SYS (Red): Flickering light indicates a proper connection to the
power supply.
WPS (Green): The LED is flash about two minutes during WPS
working.
WLAN (Green): The LED is flickering during wireless activity.
LAN 1, 2, 3, 4(Green): The Link/Act LED serves two purposes. If the
LED is continuously illuminated, the Router is successfully connected to a
device through the corresponding port. If the LED is flickering, the Router is
actively sending or receiving data over that port.
WAN (Green): The Link/Act LED serves two purposes. If the LED is
continuously illuminated, the Router is successfully connected to a device
through the corresponding port. If the LED is flickering, the Router is actively
sending or receiving data over that port.

4
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
1.2 Back panel (sockets description)
WAN: 10/100Mbps RJ45 port. The WAN port is where you will connect
Cable/DSL Modem or other LAN.
LAN (1, 2, 3, 4): 10/100Mbps RJ45 Auto-sensing. These four LAN ports
are where you will connect networked devices, such as PCs, print servers,
remote hard drives, and anything else you want to put on your network. If
you connect this product with the Hub (or Switchboard) correctly, the
Router’s corresponding LED and the Hub’s (or the Switchboard’s) must be
illuminates.
POWER: Power inlet.
RESET (WPS): The Reset Button has two functions, WPS and Factory
Default. When press it less than 2 seconds, it is WPS function and the Reset
LED will flash two minutes, than 6 seconds, the router will restore to factory
default.

5
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
2 Hardware Installation
1. Make sure that all devices including your PCs, modem and router are
powered off.
2. Connect your Internet access device such as cable or DSL modem to
the router WAN port using a cat 5e patch cord.

6
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
3. Turn all the devices on.
4. Power the router up.
3 Quick Installation Guide
3.1 TCP/IP Settings
Before you can access and configure router, you have to setup your PC
network adapter IP address. Connect your PC to the router LAN port. Follow
the steps below to access the built-in router web-interface (for Windows OS).
Note: The router default IP address is: 192.168.1.1
1. Choose Network connections from the Control Panel.
2. Click with the right mouse button over the Network adapter connected
to the router. Choose properties from the popup menu which would then
appear.
3. Select TCP/IP v.4 from the next window and click Properties
4. Select “Obtain an IP address automatically” and “Obtain DNS server
address automatically” in the IP Address tab.
5. Click OK to complete the install procedure. You might need to restart
your PC to activate these settings.
You can verify that your PC got correct IP address selecting Start  Run
 cmd and then entering command: ipconfig /all.

7
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M

8
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
3.2 Getting Started
To access the router web-interface, open a web-browser such as Internet
Explorer and enter the IP address of the router (192.168.1.1).
You will be prompted to enter the login and password. The default
Login/Password is: admin/admin
Upon a successful login you will see the status page.

9
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
3.3 Setup Wizard

10
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Click on the “Wizard” option to setup your router step by step in a simple
way. There are six steps to follow:
Please follow the steps to complete the router configuration.

11
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Step 1 – Operation Mode Settings
The router supports three operation modes: Gateway, Bridge and
Wireless ISP. Each mode is suitable for different purpose, please choose the
correct mode.

12
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Step 2 – Time Zone Settings
The Time Configuration option allows you to configure, update, and
maintain the correct time for the internal system clock. Daylight Saving can
also be configured to automatically adjust the time when needed.
NTP client update: Check this box to connect to the NTP Server and
synchronize Internet time.
Automatically Adjust Daylight Saving: If you check this box the system
will take the summer time into consideration.
Time Zone Select: Select the Time Zone from the drop-down menu.
NTP Server: Select the NTP Server from the drop-down menu.

13
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Step 3 – LAN Settings
Setup the IP address and network mask for the LAN interface.
Step 4 – WAN Settings
The router supports five access modes for the WAN, please choose the
correct mode according to your Internet Service Provider (ISP).
Mode 1: DHCP Client

14
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Select DHCP Client to obtain IP Address automatically from your ISP.
This mode is commonly used for Cable modem services.
Mode 2: Static IP
Select Static IP Address if the IP information is provided to you by your
ISP. You will need to enter the IP address, subnet mask, gateway address,
and DNS address (-es) provided to you by your ISP. Each IP address
entered in the fields must be in the appropriate IP form, which are four octets
separated by a dot (x.x.x.x). The router will not accept the IP address if it is
not in this format.
IP Address: Enter the IP address assigned by your ISP

15
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Subnet Mask: Enter the Subnet Mask assigned by your ISP.
Default Gateway: Enter the Gateway assigned by your ISP.
DNS: The DNS server information will be supplied by your ISP (Internet
Service Provider.)
Mode 3: PPPoE

16
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a
PPPoE connection. Your ISP will provide you with a username and
password. This option is typically used for DSL services.
User Name: Enter your PPPoE user name.
Password: Enter your PPPoE password.
Mode 4: PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a
PPTP connection. Your ISP will provide you with IP information and PPTP

17
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Server IP Address, of course it also includes a username and password.
This mode is typically used for DSL services.
IP Address: Enter the IP address.
Subnet Mask: Enter the subnet Mask.
Server IP Address: Enter the PPTP Server IP address provided by your
ISP.

18
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
User Name: Enter your PPTP username.
Password: Enter your PPTP password.
Mode 5 L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP
connection. Your ISP will provide you with a username and password.
IP Address: Enter the IP address.

19
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Subnet Mask: Enter the subnet Mask.
Server IP Address: Enter the PPTP Server IP address provided by your
ISP.
User Name: Enter your PPTP username.
Password: Enter your PPTP password.
Step 5 – WLAN Settings

20
GEMBIRD EUROPE B.V. http://www.gembird.eu
All brands and logos are registered trademarks of their respective owners
NSW-R4 WIRELESS BROADBAND ROUTER, 300M
Wireless Interface: If you do not want to use the wireless interface,
uncheck the box to disable all the wireless functions.
Band: Supported 802.11B, 802.11G, 802.11N and mixed.
Mode: Supported AP, Client, WDS and AP+WDS mode.
Network TYPE: This type is only valid in client mode.
SSID: Service Set Identifier, external name of your wireless network.
Channel width: Select 40MHz if you use 802.11n or 802.11n mixed mode,
otherwise 20MHz, it is default value.
Control Sideband: it is only valid when you choose channel width 40MHz.
Channel Number: Indicates the channel setting for the router. By default
the channel is set to 6.
Step 6 – WLAN Security Settings
Secure your wireless network by turning on the WPA or WEP security
feature of the router. You can set WEP and WPA-PSK security mode.
The following picture shows how to set the WEP security.