German Knife GBS-230A Specifications

OWNER & OPERATOR
INSTRUCTION MANUAL
ModelNo.
GB S- 230A
GB S- 270S
www .turboairinc.com
TABLE OFCONTENTS
IMPORTANT SAFETY NOTICE
To ensure safe and trouble free performance of
your new German knife slicer, we suggest that
all personnel who
will use and maintain the
slicer read and understand the
manual before
operating the equipment. Should there be any
questions or if we can be of further assistance,
please call
us toll free at [phone] .
FOR PARTS AND/OR SERVICE, CONTACT:
GERMAN KNIFE, INC.
1-800-500-3519
www.gkradiance.com

2
PAGE
Operating and Service Manual 3
Outer Dimension 4
Specification, Motor Wiring 5
Adjustments 6
Start, When the Machine Operation is Blacked Due to Overloads 7
Cleaning, Changing Saw Blade 8
Parts Description GBS-230A 9
Parts Description GBS-270S 10
Electronic Circuit ------------------------------------------------------------------------------11
Troubleshooting--------------------------------------------------------------------------------12
Warranty ----------------------------------------------------------------------------------------13
German Knife Inc
4184 E. Conant St., Long Beach, CA 90808
Phone: [phone]
Fax: [phone]
www.turboairinc.com
TABLE OF CONTENTS

3
OPERATING AND SERVICE MANUAL
WARNING TO ALL PURCHASERS, OPERATORS AND OPERATION SUPERVISORS :
FAILURE TO READ AND ADHERE TO THE FOLLOWING IMPORTANT INSTRUCTIONS
COULD RESULT IN BODILY INJURY.
NOTE TO ELECTRICIAN: IF THE CARD & PLAY ON THIS MACHINE IS NOT CONNECTED
TO THE ELECRICAL SUPPLY SOURCE, THEN IT SHOULD BE EQUIPPED WITH, OR CON-
NECTED TO, A LOCKABLE MANUALLY-OPERATED DISCONNECT SWITCH.
1. Do not electric wire this Meat Saw. Have only a qualified and certified electrician wire this
Meat Saw as required. Be sure machine is grounded. Failure to ground this machine could
result in electric shock.
2. Do not place machine on sloping floor. Always place machine on flat non-skidfloor.
3. Do not use this Meat Saw for non-food products.
4. Do not attempt to operate this Meat Saw until this machine has been inspected and
demonstrated by the seller recognized GERMAN KNIFE Representative.
5. Do not attempt to operate this Meat Saw unless you or the operator has been properly
trained. Improper use or operation of this Meat Saw could result in bodily injury.
6. Do not leave Meat Saw in operation unattended.
7. Do not tamper, bypass, remove fixed guards, safety interlock electrical switches or any
other safety device.
8. Do not at any time force feed product through this Meat Saw.
9. Do not alter or modify this Meat Saw in any way from its original form.
10. Always use safety pusher plate supplied with each Meat saw when cutting small
product.
11. Do not touch moving blade or moving parts. Never place hand or arm between blade
and head column structure.
12. Always disconnect power supply before removing shrouds, removable guards, covers,
doors, fences, panels for servicing, cleaning or any other reason.
13. Use only GERMAN KNIFE parts and accessories properly installed, contact you
nearest service agency or The GERMAN KNIFE CORP. for authorized referral assistance.
14. Meat saw operating manuals as supplied with this power cutter are available from
GERMAN KNIFE.

4
OUTER DIMENSION
GBS-230A
GBS-270S

5
SPECIFICATION
MOTOR WIRING
1. Interchange of current is made in motor outlet box. Changing instructions are on
motor
plate or motor outlet box.
2. All Meat Saw are wired 120 volts unless otherwise specified. Be sure motor specifications
(voltage, cycle, phase) match power supply line. Be sure line voltage is up to specification.
3. Connect leads to machine in a manner that will be approve by local electrical inspectors.
4. We recommend not less than No. 12 wire, otherwise an overload condition may
occur .
5. The V-Beltis packed loose in machine to prevent deformation, and must be installed of
pulleys at time of wiring
motor .
6. The
GERMANY KNIFE CORP is not responsible for permanent wiring connection or
installations.
MODEL GBS-230A GBS-270S
Dimension 19" x 23.9" x 40"27.1" x 44.6" x 65.5"
Motor AC120Vx1Phasex3/4HP AC120Vx1Phasex1.5HP
We i g ht 88lbs 275lbs
Ta b l e
Stationary
7.6"x19.7" 11"x30"
Carriage 13.8"x22.4" 9.5"x13"
Loading 14" 22.2"
Length of Saw Blade 65.5"(1665mm) 92.9"(2360mm)