German pool ADR-289 User manual

P.1
Please read these instructions and warranty information carefully
before use and keep them handy for future reference.
USER MANUAL
Online Warranty Registration
Smart UVC Clothes Drying Rack ADR-289

P.2
Please register your warranty information now !
For Warranty Terms & Conditions,
please refer to the last page of this user manual.
請即進行保用登記！
有關保用條款細則，請看說明書最後一頁。

P.3
Table of Contents
Warnings & Safety Precautions
Product Structure
Installation Instructions
Operation Instructions
Troubleshooting
Technical Specication
Warranty Terms & Conditions
04
05
06
08
09
10
19

P.4
Warnings & Safety Precautions
WARNING!
Read all instructions carefully before using this product.
• This product is for domestic indoor use only. If this product is used for any commercial, industrial,
rental or other purposes, product warranty will be VOIDED.
• This product is not intended for use by children or persons with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of this product by an adult responsible for their safety.
• Mind your children and DO NOT let children play with this product.
• Cleaning and user maintenance shall not be made by children without supervision.
• Check the voltage indicated on the rating label before using this product.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualied persons in order to avoid hazards.
• Unplug this product from the power source before cleaning and maintenance.
• Contact German Pool authorized service technician for repair or maintenance of this product.
1. The ceiling selected for installing this product must be sturdy so that the expansion anchors can
be embedded fully and securely.
2. DO NOT sharing the same power supply with other electrical appliances.
3. For safety reasons, this product must be earthed, and the mains voltage must correspond to
the voltage stated on this product’s rating label. DO NOT use power cord with core thinner than
0.75mm2. In order to ensure the normal operation of this product, the main body of this product
must be installed at a location where rain cannot reach.
4. DO NOT disassemble this product by yourself. Repair work must be carried out by German Pool
Customer Service & Repair Centre.
5. DO NOT use this product during thunderstorms.
6. The connecting xed wiring center must be equipped with an all-pole disconnecting device with a
contact gap of at least 3 mm.
7. If the power cord is damaged, in order to avoid danger, it must be replaced by professionals from
the manufacturer’s maintenance department or similarly qualied technicians.
8. WARNING! This product is specically for drying woven fabrics.
WARNING!
• This product is equipped with a UVC lamp. DO NOT stare directly at the UV light source.
• DO NOT look at the UVC light from any angle to avoid causing permanent damage to the eyes.
• DO NOT shine the UVC light on bare skin, and DO NOT expose your skin to the UVC light.
• When UVC Button is pressed, UVC sterilization will activate immediately! DO NOT stand below or
near this product when pressing the UVC Button!
• Stand away from this product before pressing the UVC Button; if this product is installed on the
balcony ceiling, close the curtains before pressing the UVC Button to activate UVC Sterilization
Function; if this product is installed in a room, leave the room and shut the door before pressing
the UVC Button to activate UVC Sterilization Function.

P.5
Product Structure
Main Body
Scissor Frame
Hanger Rod
Extension
Rod A
Extension Rod B
Swing Arm
Main Unit
Air Outlet
Air Outlet
Lighting & UVC Lamp

P.6
Installation Instructions
Installing The Main Unit
1. Remove the left and right end covers of the product, and insert one end of the main unit’s frame
plate into the 5mm space of the expansion anchors (between the upper and lower bolts), then
tighten up the lower bolts to secure this side of the frame plate.
2. Fit the other side of the main unit frame plate over the other 2 expansion anchors (the ones with
the lower bolts removed), then screw on the lower bolts so that the whole frame plate is securely
installed.
3. Connect the wires correctly: Brown to live wire, blue to neutral wire, yellow-green to ground wire,
then wrap the wires with insulating tape and lay them into the gap between the main unit and the
ceiling.
Tighten the boltTighten the bolt
Insert frame plate into the
space then tighten bolt
Installing The Expansion Anchors
1. Measure the ceiling installation location and mark the spots for the expansion anchors. If this
product will replace your ceiling lamp, make sure to disconnect the power source of the ceiling
lamp beforehand.
2. Tape the paper template guide to the ceiling, then drill four Ø10x80mm holes as marked on the
template.
3. Install the expansion anchors into the drilled holes and tighten the screws. On one end, loosen
the 2 lower bolts of the expansion anchors so that there is a 5mm gap between the upper and
lower bolts; on the other end, take the 2 lower bolts off completely.
Loosen 2 lower bolts 5mm on the other endTake off 2 lower bolts on one end
5mm 5mm

P.7
Installing The Scissor Frame
1. Install one side of the scissor frame to the main unit and tighten the screws.
2. Thread the ball stopper of the steel cable into the small tting on the scissor frame and make
sure it is securely locked in. Repeat steps 1 and 2 with the other side of the scissor frame.
3. Snap on the end covers by aligning the latches with the holes on the main body and pushing
inwards. Reconnect the power source of your original balcony lamp.
Installing The Extension Rods
1. Hook one end of the swing arm onto Extension Rod A, and the other end onto Extension Rod B,
screw on the end cap tightly. Repeat with the other swing arm.
2. When you need to use Extension Rod B, swing it downwards, and swing it back up onto the hanger
rod after use.
Installing The Hanger Rod
Align the screw hole at the base of the scissor frame with the screw hole near the end of the hanger
rod, and tighten with screw. Do the same with the other three sides.
Installation Instructions
Main Unit
Scissor Arm
Align the two holes
Ball Stopper
Steel Cable End Cover
Swing Arm
End CapExtension Rod A
End CapExtension Rod B

P.8
Operation Instruction
WARNING!
• This product is equipped with a UVC lamp. DO NOT stare directly at the UV light source.
• DO NOT look at the UVC light from any angle to avoid causing permanent damage to the eyes.
• DO NOT shine the UVC light on bare skin, and DO NOT expose your skin to the UVC light.
• Remote Control is equipped with a motion sensor, it is recommended that the remote control be
installed next to the door of the room or balcony.
Motion Sensor
NOTE:
In any mode, when On/Off Button is pressed, product will turn off immediately. Pressing On/Off
Button again will not turn the product back on. To turn the product back on, press your desired mode
button.
Automatic Motion Sensor
This product is equipped with a motion sensor which will automatically turn the product on and off
when motion is detected.
1. Automatically turn off UVC Lamp: When UVC Sterilization Lamp is turned on, and motion is
detected near the remote control, the UVC lamp will automatically turn off and sterilization
process will terminate.
2. Automatically turn on lighting: When power is connected, and motion is detected near the remote
control, the lighting will automatically turn on; when lighting is turned on, if motion sensor does
not detect any motion, the lighting will automatically turn off.
UUVVCC
UP STOP UVC DOWN
LAMP ON/OFF HEATDRY

P.9
Press this button to turn the lighting on or off.
• Press this button to raise the hanger rod.
• Hanger rod will automatically stop when it is completely raised up.
In any mode, press this button to turn off the product.
Press this button to stop the hanger rod from rising or lowering.
• Press this button to turn on or turn off Air Dry Function.
• Maximum drying time is 2 hours. Air Dry Function will automatically turn off after
2 hours.
• Press this button to turn on or turn off Heat Dry Function; when Heat Dry
Function is turned on, Air Dry Function will automatically turn on simultaneously.
• Maximum drying time is 2 hours. Heat Dry Function will automatically turn off
after 2 hours, and Air Dry Function will automatically turn off as well.
• When Heat Dry Function is turned off, the fan will run for an extra 10 seconds to
dissipate residual heat.
• Press this button to lower the hanger rod.
• Hanger rod will automatically stop when it has lowered down completely.
• Press this button to turn on or turn off UVC Sterilization Function.
• Maximum UVC sterilizing time is 30 minutes. UVC Sterilize Function will
automatically turn off after 30 minutes.
WARNING! When this button is pressed, UVC Sterilization will activate
immediately! DO NOT stand below or near this product when pressing the UVC Button!
WARNING! Stand away from this product before pressing the UVC Button; if this
product is installed on the balcony ceiling, close the curtains before pressing the UVC
Button to activate UVC Sterilization Function; if this product is installed in a room,
leave the room and shut the door before pressing the UVC Button to activate UVC
Sterilization Function.
Button
Lighting
Lamp
Up
On/Off
Stop
Air Dry
Sterilize
Heat
Dry
Down
Function
Operation Instruction

P.10
Technical Specication
• Specication is subject to change without prior notice.
• If there is any inconsistency or ambiguity between the English version and the Chinese version,
the Chinese version shall prevail.
• Refer to www.germanpool.com for the most update version of the user manual.
Model
Power
Voltage
Frequency
Product Dimensions
Net Weight
Maximum Load
ADR-289
893 W
220-230 V~
50 Hz
Retracted: (H) 135±10mm (W) 1290±10mm (D) 520±5mm
Extended: (H) 1550±10mm (W) 2265±10mm (D) 505±5mm
9.6 kg
35 kg
Troubleshooting
Problem Reason Solution
Remote control does not
respond
UVC lamp does not light
Hanger rod stopped midway
Lighting lamp does not light
There is no power to the main
unit
Scissor frame is not retracted
fully
There is an obstruction
stopping the hanger rod
There is no power to the main
unit
Lamp is broken
Motor overheat protection
UVC lamp is broken
Remote control battery is dead
Connect the power source
Turn on the UVC lamp again
after the scissor frame has
retracted fully
Remove the obstruction
Connect the power source
Replace the lamp
Let the product cool down
before restarting
Replace the UVC lamp
Replace the battery
WARNING!
If problem persists, please contact German Pool Customer Service & Repair Centre for assistance. DO
NOT disassemble this product by yourself.