GFI System SYNESTHESIA User manual

1.PresetSystem
SYNESTHESIAhas32presetsorganizedwithin4pages,whereeachpagecontains4banks,andeachbankcontains2patches(A&B).
A|B
Bank‐1
A|B
Bank‐2Bank‐3Bank‐4
A|B
PAGE1PAGE2PAGE4
Youmaysetthemaximumnumberofbanksorpagestoaccess.Forexample,restrictingthepresetaccesstotwopagesgivesyou
2pagesx4banksx2patches=16presets.
SuchrestrictionisusefulifyouarenotusingMIDIcontrollerforpresetswitchingasitcouldgetunwieldytonavigatetoomany
presetlocationsinconsequentialmanner.
PagerestrictioncanbesetinGlobalSettingsmenu.
A|B
SYNESTHESIA QUICKSTARTGUIDE
(firmwarev1.0.2)
A|B
Bank‐5
A|B
Bank‐7Bank‐8
A|BA|B
Bank‐6
A|B
Bank‐13
A|B
Bank‐14Bank‐15Bank‐16
A|BA|B
2.GlobalSettingsandOptions
Everyknobisalsoabutton.Thefollowingoperationscanbedoneoneachknob:
TURNPUSHorTAPHOLDTWIST(turnwhileholdingdown)
2.1Globals
HolddowntheYencoderuntilthescreenreads“GLOBALSETTINGS”.
UsetheYencodertonavigatetheGlobalsmenu.
<toleavethemenuwithoutmakinganychanges:holddowntheYencoderagainuntilscreenreturnstothemainscene>

2.2Options(specifiedonper‐presetbasis)
HolddowntheXencoderuntilthepedalenterstheOptionsmenu.
UsetheXencodertonavigatetheOptionsmenu.
<toleavethemenuwithoutmakinganychanges:holddowntheXencoderagainuntilscreenreturnstothemainscene>
>>Melancholidy \1
TRMOLO ++ UNIVBE
Bank[1,2,3,4]indicatorLEDs
FootswitchB/XFootswitchA/Y
ParameterControls[DSP‐Y]
 Speed/SP1
 Depth/SP2
 Tweak/SP3
 Algorithm
ParameterControls[DSP‐X]
 Speed/SP1
 Depth/SP2
 Tweak/SP3
 Algorithm
LEDA/YLEDB/X
SP=SecondaryParameter

where to save?
A <push> B
SYNESTHESIA QUICKSTARTGUIDE
3.3SAVEPRESET
HolddownXandYencodersuntilapromptappearsonthescreen.




PushfootswitchAtosavetopatchA,orpushfootswitchBtosavetopatchB




3.4BYPASSTHEPEDAL
TapfootswitchA/YorB/X,whicheverpresetiscurrentlyactive(correspondingLEDison).
(firmwarev1.0.2)
Visitourwebsitewww.gfisystem.comforfullusermanual,editorsoftwareandwarrantyregisteration.
>>My Preset \1
TRMOLO << PHASER
Presettitle
Algoname(DSP‐Y)
Page#
Algoname(DSP‐X)
Afterpresetissaved,thepreset’stitlecanbechangedinOptions(Options‐>TitleEditor)
4.NavigatingtheAlgorithms
TurntheXEncodertoselectanalgorithmtoonDSP‐X,andturntheYEncodertoselectanalgorithmtorunonDSP‐Y.
PushtheXEncodertotoggleDSP‐Xonandoff,similiarly,pushtheYEncodertotoggleDSP‐Yonandoff.
02.Harmonic Trem
HCTREM
Algo#Algolongname
6‐letteralgoshortname
5.MasterVolume
Asinglecontrolisprovidedtosettheoverallvolumeofthepedal,from‐3dBto+3dB.
TwisttheYencoder,clockwisetoincreasevolume,anti‐clockwisetoreducevolume.
VOLUME (dB) +2
PREV:+1
<ThedisplaywillshowthetitlesofbothpatchAandpatchBthatwerestoredinthebank>
3.NavigatingthePresets
A>>Phantoms /
B>>Vibro Lush 2
PatchAtitle
PatchBtitlePage#
<Atthispoint,Ifyou’dliketocancelsavingtoapreset:holddowntheXandYencodersagain>
Mastervolumeisspecifiedonper‐presetbasis.
3.1LOADAPRESET
PressfootswitchA/YtoloadpatchA,orfootswitchB/XtoloadpatchB.
3.2LOADAPRESETINANOTHERBANK
Selectthedesiredbank.
PressfootswitchA/YtoloadpatchA,orfootswitchB/XtoloadpatchB.

Thereare2waystoselectabank:
Method1:PressfootswitchA/YandB/Xsimultaneously(donothold).
Method2:TwisttheXencoder(clockwiseforBank‐Uporanti‐clockwiseforBank‐Down).