Gifas LaneLED INOX42 User manual

LaneLED INOX42
Page 1 / 22
Created
22.03.2017
roen
Modified
11.07.2018
roen
Object-ID
845816
LaneLED INOX42
Installation instructions
VERSION
MODIFICATIONS
1.0
First edition
1.1
Supplement in chapter 5.1

LaneLED INOX42
Page 2 / 22
Created
22.03.2017
roen
Modified
11.07.2018
roen
Object-ID
845816
Table of contents
1General information................................................................................................................3
1.1 Marking concept for hazards and hints..................................................................................3
1.2 Responsibilities of the operator.............................................................................................3
2Introduction.............................................................................................................................4
2.1 Installation conditions LaneLED............................................................................................4
3Required tools.........................................................................................................................5
3.1 Consumables........................................................................................................................7
4Montage LaneLED INOX42 .....................................................................................................8
4.1 In general..............................................................................................................................8
4.2 Mounting...............................................................................................................................8
5Installation of LaneLED light bars..........................................................................................9
5.1 Mounting the adapter to the LED carrier profile.....................................................................9
5.2 Fitting the system cable ........................................................................................................9
5.3 Supply line connection..........................................................................................................9
5.4Assembly of LED light bar: variant 1 ...................................................................................11
5.4.1 Current collector connection....................................................................................11
5.4.2 LED light bar connection..........................................................................................12
5.5 Assembly of LED light bar: variant 2 ...................................................................................12
5.5.1 Current collector connection....................................................................................12
5.5.2 LED light bar connection..........................................................................................12
5.6 Diffusor mounting................................................................................................................14
6Detailed installation information..........................................................................................15
6.1 Press current collector onto the system cable with special crimping pliers ..........................15
6.2 Finishing the system cable ends.........................................................................................16
6.3 Connecting/repairing the system cable ...............................................................................18
6.4 Isolation of system cables...................................................................................................21
7Service...................................................................................................................................22
7.1 Service addresses ..............................................................................................................22
7.2 Imprint.................................................................................................................................22

LaneLED INOX42
Page 3 / 22
Created
22.03.2017
roen
Modified
11.07.2018
roen
Object-ID
845816
1 General information
1.1 Marking concept for hazards and hints
Hazard
Hazardous situation which will cause serious injury or even death if it is not prevented.
Caution
Hazardous situation which could cause slight to moderate injury if it is not prevented.
Hint
Indicates information which does not concern personal injury, e.g. hints in respect of material damage.
Protective measures
Increase safety by applying a protective measure.
1.2 Responsibilities of the operator
-Make sure that this document is always kept in a safe place in a legible form together with the product.
-Read these instructions carefully before first start-up of the product.
-This product has been developed and produced exclusively for the use indicated in these documents.
Every other use, which is not mentioned explicitly, could affect the intactness of the product and/or could
constitute a source of danger.
-The manufacturer rejects any liability for damage which has been caused by incorrect or non-intended use
of the product.
-In countries, which do not belong to the European Community, the national legal reference regulations as
well as the standards and regulations applicable in these countries have to be observed for warranty of a
corresponding safety level.
-The installation has to be carried out according to the applicable regulations.
-The manufacturer assumes no liability for inexpert execution of installation as well as deformations which
may occur during operation.
-The electric power supply has to be switched off before executing any action on the installation.
-Exclusively original parts of the manufacturer shall be used for maintenance. Maintenance work may be
carried out by qualified staff only.
-All procedures which are not explicitly mentioned by the manufacturer in the instructions are not permitted.
-The packing material must not be stored within the reach of children as it could be a potential source of
danger.

LaneLED INOX42
Page 4 / 22
Created
22.03.2017
roen
Modified
11.07.2018
roen
Object-ID
845816
2 Introduction
To ensure proper installation, the following steps and notes must be complied with under all circumstances. Only
this way can it be ensured that the product will work to complete satisfaction.
Hazard
Read all instructions before starting installation. Our sales department will be happy to answer any questions you
may have.
2.1 Installation conditions LaneLED
-To comply with the necessary operating voltage, the number of
connected LaneLED light bars must be adjusted to the linelength.
-The maximum line length for the number of LaneLED light bars
required must be calculated for the specific installation.
-LaneLED light bars must be calculated specifically for the plant.
-Installation only in dry weather or with the installation sitecovered.
-For correct installation, the protective measures and
-For mounting of the GFK handrail, observe the provisions and
instructions of the manufacturer and the local object provisions
(specifications for dowels and threaded rods, supporting distance,
SIA standards, etc…). Observe a standardcompliant and technically properly executed installation.

LaneLED INOX42
Page 5 / 22
Created
22.03.2017
roen
Modified
11.07.2018
roen
Object-ID
845816
3 Required tools
Crimping tool mechanical Item no. 860457,
or electric Item no. 860456
Pliers to cut off cables
Light barping pliers for system cables 2x2.5 mm2
Hot-air gun
Circular saw
Note
Ensure the correct saw blade is used (V2A, V4A)
Corrosion can result if the wrong blade is used.
Power supply 24VDC (20-36VDC)

LaneLED INOX42
Page 6 / 22
Created
22.03.2017
roen
Modified
11.07.2018
roen
Object-ID
845816
Large utility knife

LaneLED INOX42
Page 7 / 22
Created
22.03.2017
roen
Modified
11.07.2018
roen
Object-ID
845816
Recommended:
-Device for unrolling cables
-Cable lug crimping pliers for press connector
-Screwdriver size 5 (to dismount LaneLED after wrong
connection if necessary)
-Head lamp, measuring tape, material/tool cart, etc.
3.1 Consumables
Heat shrink tube with glue (6 mm/2 mm):
Item no. 010300
If appl. insulation tape 2 M Scotch no. 23, black
Item no. 152743
If appl. crimp connector 1.5-2.5 hot-shrinking Raychem, blue
Item no. 019875
Solder connector 1.5-2.5 heat-shrinkable NSPA, transparent
Item no. 172745

LaneLED INOX42
Page 8 / 22
Created
22.03.2017
roen
Modified
11.07.2018
roen
Object-ID
845816
4 Montage LaneLED INOX42
4.1 In general
Note
Examine the arrangement of the materials before assembly. Are all the parts required for assembly available?
Do certain parts have to be adjusted on-site?
4.2 Mounting
-Mount hand rail as shown in the image.
-Carry out adjustments to the hand rail, such as
cutting or welding, directly on-site.

LaneLED INOX42
Page 9 / 22
Created
22.03.2017
roen
Modified
11.07.2018
roen
Object-ID
845816
5 Installation of LaneLED light bars
5.1 Mounting the adapter to the LED carrier profile
-Mount the adapter in the groove as shown in the
drawing
Note
In every case, an adapter should be installed at each
end of a LaneLED light bar. The distance between two
adapters on one light bar should be a maximum of 30
cm.
For the installation of the adapter, an M5 threaded hole
has to be drilled
- Drill D=4.2
- Thread cutter M5
5.2 Fitting the system cable
-Loop the system cable through the handrail
supports
5.3 Supply line connection

LaneLED INOX42
Page 10 / 22
Created
22.03.2017
roen
Modified
11.07.2018
roen
Object-ID
845816
-Connect the connection cable and system cable
with the press or solder connector