Gigabyte GA-8IPE1000MK User manual

When you installing AGP card, please make sure the following notice
is fully understood and practiced. If your AGP card has "AGP 4X/8X
(1.5V) notch"(show below), please make sure your AGP card is AGP
4X/8X (1.5V).
Caution: AGP 2X card is not supported by Intel®845(GE/PE) / 845(E/G)
/ 850(E) / E7205 / 865(G/PE/P) / 875P. You might experience system
unable to boot up normally. Please insert an AGP 4X/8X card.
Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X
mode AGP slot. It can be switched between AGP 2X(3.3V) or 4X/8X(1.5V)
mode by adjusting the jumper. The factory default for this card is 2X(3.3V).
The GA-8IPE1000MK (or any AGP 4X/8X only) motherboards might not
function properly, if you install this card without switching the jumper to 4X/8X
(1.5) mode in it.
Example 2: Some ATi Rage 128 Pro graphics cards made by "Power Color",
the graphics card manufacturer & some SiS 305 cards, their golden finger is
compatible with 2X(3.3V)/4X(1.5V) mode AGP slot, but they support 2X(3.3V)
only. The GA-8IPE1000MK (or any AGP 4X/8X only) motherboards might not
function properly, If you install this card in it.
Note : Although Gigabyte's AG32S(G) graphics card is based on ATi Rage
128 Pro chip, the design of AG32S(G) is compliance with AGP 4X(1.5V)
specification. Therefore,AG32S(G) will work fine with Intel®845(GE/PE) /
845(E/G) / 850(E) / E7205 / 865(G/PE/P) / 875P based motherboards.
AGP 4X/8X notch

The author assumes no responsibility for any errors or
omissions that may appear in this document nor does the
author make a commitment to update the information
contained herein.
Third-party brands and names are the property of their
respective owners.
Please do not remove any labels on motherboard, this may
void the warranty of this motherboard.
Due to rapid change in technology, some of the
specifications might be out of date before publication of
this booklet.

Sep. 2, 2005
Motherboard
GA-8IPE1000MK (2.0)

Motherboard
Sep. 2, 2005
GA-8IPE1000MK(2.0)

USER'S MANUAL
GA-8IPE1000MK (rev. 2.0)
P4 Titan Series Motherboard
Pentium®4 Processor Motherboard
Rev. 2002
12ME-IPE1KMK-2002R
* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste
and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!
* The WEEE marking applies only in European Union's member states.

- 2 -GA-8IPE1000MK(rev. 2.0) Motherboard
English
Table of Content
Warning ................................................................................................... 4
Chapter 1 Introduction ............................................................................ 5
Features Summary ...................................................................................... 5
GA-8IPE1000MK (rev.2.0) Motherboard Layout ......................................... 7
Block Diagram ............................................................................................. 8
Chapter 2 Hardware Installation Process ............................................. 11
Step 1: Install the Central Processing Unit (CPU)..................................... 12
Step 1-1: CPU Installation ................................................................................. 12
Step 1-2: CPU Cooling Fan Installation ............................................................. 13
Step 2: Install Memory Modules ................................................................ 14
Step 3: Install expansion cards ................................................................. 16
Step 4: Connect ribbon cables, cabinet wires and power supply ............ 17
Step 4-1: I/O Back Panel Introduction ............................................................... 17
Step 4-2: Connectors Introduction ..................................................................... 19
Chapter 3 BIOS Setup .......................................................................... 33
The Main Menu (For example: BIOS Ver. : G2 ) ...................................... 34
Standard CMOS Features......................................................................... 36
Advanced BIOS Features .......................................................................... 39
Integrated Peripherals .............................................................................. 41
Power Management Setup ....................................................................... 46
PnP/PCI Configurations ............................................................................. 49
PC Health Status........................................................................................ 50
Frequency/Voltage Control ........................................................................ 52

Table of Content
English
- 3 -
Load Fail-Safe Defaults ............................................................................. 54
Load Optimized Defaults ........................................................................... 55
Set Supervisor/User Password .................................................................. 56
Save & Exit Setup ....................................................................................... 57
Exit Without Saving ................................................................................... 58
Chapter 4 Technical Reference ............................................................ 61
@BIOS™ Introduction ............................................................................... 61
EasyTune™ 5 Introduction ........................................................................ 62
Flash BIOS Method Introduction ............................................................... 63
2- / 4- / 6-Channel Audio Function Introuction .......................................... 67
Xpress Recovery2 Introduction ................................................................. 72
Chapter 5 Appendix ............................................................................. 77

- 4 -GA-8IPE1000MK(rev. 2.0) Motherboard
English
Warning
Computer motherboards and expansion cards contain very delicate Integrated Circuit
(IC) chips. To protect them against damage from static electricity, you should follow
some precautions whenever you work on your computer.
1. Unplug your computer when working on the inside.
2. Use a grounded wrist strap before handling computer components. If you do not have one, touch
both of your hands to a safely grounded object or to a metal object, such as the power supply
case.
3. Hold components by the edges and try not touch the IC chips, leads or connectors, or other
components.
4. Place components on a grounded antistatic pad or on the bag that came with the components
whenever the components are separated from the system.
5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX power
connector on the motherboard.
If the motherboard has mounting holes, but they don't line up with the holes on the base and there are
no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting
holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so be careful of
your hands). In this way you can still attach the motherboard to the base without worrying about short
circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard
PCB surface, because the circuit wire may be near by the hole. Be careful, don't let the screw contact
any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the
board or cause board malfunctioning.
Installing the motherboard to the chassis...

Introduction
English
- 5 -
Form Factor y24.3cm x 24.3cm Micro ATX size form factor, 4 layers PCB
CPU ySocket 478 for Intel®Micro FC-PGA2 Pentium®4 processor
ySupport Intel®Pentium®4 (Northwood, Prescott) processor
ySupport Intel®Pentium®4 Processor with HT Technology *
yIntel®Pentium®4 800/533/400MHz FSB
y2nd cache depends on CPU
Chipset yIntel®Chipset 865PE HOST/AGP/Controller
yIntel®ICH5 I/O Controller Hub
Memory y4 184-pin DDR DIMM sockets
ySupports Dual Channel DDR400/DDR333/DDR266 DIMM
ySupports 128MB/256MB/512MB/1GB unbuffered DRAM
ySupports up to 4GB DRAM (Max)(Note 1)
ySupports only DDR DIMM
I/O Control yITE8712F
Slots y1 AGP slot 4X/8X (1.5V) device support
y3 PCI slot supports 33MHz & PCI 2.3 compliant
On-Board IDE y2 IDE controllers provides IDE HDD/CD-ROM (IDE1, IDE2) with
PIO, Bus Master (Ultra DMA33/ATA66/ATA100) operation modes
yCan connect up to 4 IDE devices
SerialATA y2 Serial ATA connectors in 150 MB/s operation mode
yControlled by ICH5
On-Board Peripherals y1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M
and 2.88M bytes
y1 Parallel port supports Normal/EPP/ECP mode
y2 Serial ports (COMA & COMB)
y8 USB 2.0/1.1 ports (4 x Rear, 4 x Front by cable)
y1 IrDA connector for IR/CIR
y1 FrontAudio connector
Chapter 1 Introduction
to be continued......
Features Summary
Due to chipset (Intel 865PE) architecture limitation, DDR 400 memory module is only
supported when using FSB 800 Pentium 4 processor. A FSB 533 Pentium 4 processor will
support DDR333 and DDR266 memory module. A FSB 400 Pentium 4 processor will only
support DDR 266 memory module.
(Note 1) Due to standard PC architecture, a certain amount of memory is reserved for system
usage and therefore the actual memory size is less than the stated amount.
For example, 4 GB of memory size will instead be shown as 3.xxGB memory during
system startup.

- 6 -GA-8IPE1000MK(rev. 2.0) Motherboard
English
Hardware Monitor yCPU/System fan revolution detect
yCPU temperature detect
yCPU warning temperature
ySystem voltage detect
yCPU/System fan fail warning
yCPU Smart Fan control
On-Board LAN yBuilit in Intel®82562 Chipset
Data transfer rate 10/100 supported
y1 RJ45 port
On-Board Sound yRealtek ALC655 codec
yLine Out / 2 front speaker
yLine In / 2 rear speaker (by s/w switch)
yMic In / center & subwoofer (by s/w switch)
yCD In / AUX In / Game port
PS/2 Connector yPS/2 Keyboard interface and PS/2 Mouse interace
BIOS yLicensed Award BIOS
Additional Features yPS/2 Keyboard power on by password
yPS/2 Mouse power on
ySTR (Suspend-To-RAM)
yAC Recovery
yPoly fuse for keyboard over-current protection
yUSB KB/Mouse wake up from S3
ySupports @BIOS
ySupports EasyTune(Note 2)
ySupports clear password function
Please set the CPU host frequency in accordance with your processor's specifications.
We don't recommend you to set the system bus frequency over the CPU's specification because
these specific bus frequencies are not the standard specifications for CPU, chipset and most of the
peripherals. Whether your system can run under these specific bus frequencies properly will
depend on your hardware configurations, including CPU, Chipsets, SDRAM, Cards…etc.
"*" HT functionality requirement content :
Enabling the functionality of Hyper-Threading Technology for your computer system requires all
of the following platform components:
- CPU: An Intel®Pentium 4 Processor with HT Technology
- Chipset: An Intel®Chipset that supports HT Technology
- BIOS: A BIOS that supports HT Technology and has it enabled
- OS: An operation system that has optimizations for HT Technology
(Note 2) EasyTune functions may vary depending on different motherboards.

Introduction
English
- 7 -
GA-8IPE1000MK (rev. 2.0) Motherboard Layout
GA-8IPE1000MK
KB_MS
COMA
ATX_12V
CD_IN
F_AUDIO
F_PANEL
BAT
SYS _FAN
Intel ICH5
Intel 865PE
SOCKET 478
CPU_FAN
ATX
FDD
IDE2
PCI1
PCI2
PCI3
DDR1
CODEC
ITE8712
BIOS
Buzzer
F_USB2
CI
COMB
IDE1
CLR_PWD
Intel
82562
F_USB1
AUX_IN
IR_CIR
RAM_LED
PWR_LED
USB LAN
R_USB
AUDIO1
DDR2 DDR3 DDR4
GAME INFO_LINK
SUR_CEN
2X_DET
S_ATA1
S_ATA0
LPT
AGP

- 8 -GA-8IPE1000MK(rev. 2.0) Motherboard
English
Block Diagram
CLK GEN
CPUCLK+/- (100/133/200MHz)
AGPCLK (66MHz)
MCHCLK (100/133/200mHz)
ICH3V66 (66MHz)
PCICLK (33MHz)
USBCLK (48MHz)
14.318 MHz
33 MHz
Intel 865PE
Intel
ICH5
CPUCLK+/- (100/133/200MHz)
System Bus
800/533/400MHz
MCHCLK (100/133/200MHz)
66 MHz
33 MHz
14.318 MHz
48 MHz
LPC BUS
AGP 4X/8X
AGPCLK
(66MHz)
3 PCI
PCICLK
(33MHz)
RJ45
AC97 Link
8 USB
Ports
ATA33/66/100
IDE Channels
Intel
82562
IT8712F
24 MHz
33 MHz
Game Port
Floppy
LPT Port
PS/2 KB/Mouse
2 COM Ports
MIC
LINE-IN
LINE-OUT
Pentium 4
Socket 478
CPU
AC97
CODEC
266/333/400MHz
2 Serial ATA
DDR RAM
BIOS

Introduction
English
- 9 -

- 10 -GA-8IPE1000MK(rev. 2.0) Motherboard
English

- 11 - Hardware Installation Process
English
Chapter 2 Hardware Installation Process
To set up your computer, you must complete the following steps:
Step 1- Install the Central Processing Unit (CPU)
Step 2- Install memory modules
Step 3- Install expansion cards
Step 4- Connect ribbon cables, cabinet wires, and power supply
Congratulations! You have accomplished the hardware installation!
Turn on the power supply or connect the power cable to the power outlet. Continue with the
BIOS/software installation.
Step 2
Step 4
Step 3
Step 4
Step 4
Step 1

- 12 -GA-8IPE1000MK(rev. 2.0) Motherboard
English
Step 1: Install the Central Processing Unit (CPU)
Step 1-1: CPU Installation
Angling the
rod to 650
1. Angling the rod to 65-degree maybe
feel a kind of tight , and then continue
pulltherodto 90-degreewhen anoise
"cough" made.
2. Pull the rod to the 90-degree directly.
Pin1 indicator
3. CPU Top View
Pin1 indicator
4. Locate Pin 1 in the socket and
look for a (golden) cut edge on the
CPU upper corner. Then insert
the CPU into the socket.
Socket
Actuation
Lever
Before installing the processor, adhere to the following warning:
1. Please make sure the CPU type is supported by the motherboard.
2. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will
cause improper installation. Please change the insert orientation.

- 13 - Hardware Installation Process
English
Step 1-2: CPU Cooling Fan Installation
1. Fasten the cooling fan supporting-
base onto the CPU socket on the
motherboard.
Before installing the CPU cooling fan, adhere to the following warning:
1. Please use Intel approved cooling fan.
2. We recommend you to apply the thermal tape to provide better heat
conduction between your CPU and cooling fan.
(The CPU cooling fan might stick to the CPU due to the hardening of
the thermal paste. During this condition if you try to remove the cool-
ing fan, you might pull the processor out of the CPU socket alone with
the cooling fan, and might damage the processor. To avoid this from
happening, we suggest you to either use thermal tape instead of
thermal paste, or remove the cooling fan with extreme caution.)
3. Make sure the CPU fan power cable is plugged in to the CPU fan
connector, this completes the installation.
Please refer to CPU cooling fan user's manual for more detail
installation procedure.
2. Make sure the CPU fan is plugged
to the CPU fan connector, than
install complete.

- 14 -GA-8IPE1000MK(rev. 2.0) Motherboard
English
Before installing the memory modules, adhere to the following warning:
1. When RAM_LED is ON, do not install / remove DIMM from socket.
2. Please note that the DIMM module can only fit in one direction due to
the one notch. Wrong orientation will cause improper installation.
Please change the insert orientation.
Step 2: Install Memory Modules
The motherboard has 4 dual inline memory module (DIMM) sockets. The BIOS will automatically
detects memory type and size. To install the memory module, just push it vertically into the DIMM
socket. The DIMM module can only fit in one direction due to the notch. Memory size can vary
between sockets.
DDR
Notch
1. The DIMM socket has a notch, so the DIMM memory
module can only fit in one direction.
2. Insert the DIMM memory module vertically into the DIMM
socket. Then push it down.
3. Close the plastic clip at both edges of the DIMM sockets
to lock the DIMM module.
Reverse the installation steps when you wish to remove
the DIMM module.

- 15 - Hardware Installation Process
English
DDR Introduction
Established on the existing SDRAM infrastructure, DDR (Double Data Rate) memory is a high
performance and cost-effective solution that allows easy adoption for memory vendors, OEMs, and
system integrators.
DDR memory is a great evolutionary solution for the PC industry that builds on the existing
SDRAM architecture, yet make the awesome advances in solving the system performance bottleneck
by doubling the memory bandwidth. Nowadays, with the highest bandwidth of 3.2GB/s of DDR400
memory and complete line of DDR400/333/266/200 memory solutions, DDR memory is the best
choice for building high performance and low latency DRAM subsystem that are suitable for servers,
workstations, and full range of desktop PCs.
Dual Channel Memory Configuration
The GA-8IPE1000MK supports the Dual Channel Technology. After operating the Dual Channel
Technology, the bandwidth of Memory Bus will add double.
GA-8IPE1000MK includes four DIMM slots, and each Channel has 2 DIMMs as following:
Channel A : DIMM 1, 2
Channel B : DIMM 3, 4
If you want to operate the Dual Channel Technology, please note the following explanations due to the
limitation of Intel chipset specifications.
1. Dual channel memory cannot be used if one or three DDR memory modules are installed.
2. If two DDR memory modules are installed (same storage capacity), one must be added to the
Channel A slot and the other in the Channel B slot in order to use dual channel memory. Dual
channel memory cannot function if both DDR memory modules are installed on the samechannel.
3. If four DDR memory modules are installed, please use memory of the same storage capacity
in order to use dual channel memory and for BIOS to detect all the DDR memory modules.
We'll strongly recommend our user to slot two DDR memory modules into the DIMMs with the same
color in order for Dual Channel Technology to work.
The following table is for Dual Channel Technology combination: (DS: Double Side, SS: Single Side)
2 memory modules
4 memory modules
DDR1 DDR2 DDR3 DDR4
DS/SS X DS/SS X
X DS/SS X DS/SS
DS/SS DS/SS DS/SS DS/SS

- 16 -GA-8IPE1000MK(rev. 2.0) Motherboard
English
Step 3: Install expansion cards
1. Read the related expansion card's instruction document before install the expansion card into the
computer.
2. Remove your computer's chassis cover, screws and slot bracket from the computer.
3. Press the expansion card firmly into expansion slot in motherboard.
4. Be sure the metal contacts on the card are indeed seated in the slot.
5. Replace the screw to secure the slot bracket of the expansion card.
6. Replace your computer's chassis cover.
7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.
8. Install related driver from the operating system.
When an AGP 2X (3.3V) card is installed the 2X_DET will light up, indicating a non-supported
graphics card is inserted. Informing users that system might not boot up normally due to AGP
2X (3.3V) is not supported by the chipset.
Please carefully pull out the small white-
drawable bar at the end of the AGP slot
when you try to install/uninstall the VGA
card. Please align the VGA card to the
onboard AGP slot and press firmly down
on the slot. Make sure your VGA card is
locked by the small white-drawable bar.