Gigabyte GA-K8RS482M-FS-02 User manual

GA-K8RS482M-FS-02
AMD Socket 939 Processor Motherboard
User's Manual
Rev. 1001

- 2 -
GA-K8RS482M-FS-02 Motherboard Layout
ATX_12V
DDR1
DDR2
ATX
GA-K8RS482M
Socket 939
USB LAN
COMA
SPDIF
CODEC
IT8712
F_USB2
F_USB1
CLR_CMOS
SYS_FAN
AUX_IN
F_PANEL
PCI2
PCI3
PCIE_16_1
SATA2
SATA3
SATA0
CPU_FAN
BIOS
PCI1
BAT
IDE2
FDD
USB
1394
AZALIA_FP
IDE1
AUDIO
SATA1
VGA
RTL8100C
ATi RS482
ATI SB450
TV_OUT
FS-02
Buzzer
F2_1394
IT8712F-A
VT6307

- 3 -
Block Diagram
AMD K8
Socket 939
CPU
CPUCLK+/-(200MHz)
33MHz
Host
Interface
ATi
RS482 66MHz
48MHz
COM Port
Floppy
48MHz
33MHz
4 Serial ATA
ATA33/66/100/
133 IDE Channels
ATI
SB450
14.318MHz
BIOS
8 USB
Ports
3 PCI
PCI Bus
RJ45
DDR 400/333/266/200MHz DIMM
Dual Channel Memory
IT 8712
Line-Out
MIC
CODEC
Line-In
SPDIF In
SPDIF Out
Center/Subwoofer Speaker Out
Side Speaker Out
Surround Speaker Out
SBLINK_CLK P/N (100MHz)
NBSRC_CLK P/N (100MHz)
NB_OSC (14.318MHz)
SBSRC_CLK P/N (100MHz)
VT6307
2 IEEE1394
RTL
8100C
VGA
PCI Express x16
PCI-ECLK
(100MHz)
PCIE_16_1
PCICLK
(33MHz)

K8RS482M-FS-02 Motherboard - 4 -
English
1-1 Feature Summary
Chapter 1 Hardware Installation
CPU Socket 939 for AMD AlthlonTM 64 / 64FX / Sempron processor (K8)
HT 1.03 (FSB 800/1000MHz)
Supports core frequencies in excess of 3000+ and faster
Chipset North Bridge: ATi RS482
South Bridge: ATI SB450
supported on the Win 2000/XP operating systems
Memory 2 DDR DIMM memory slots
Supports dual channel DDR 400/333/266/200 DIMM
Slots 1 PCI Express x 16 slot
3 PCI slots
IDE Connections 2 IDE connection (UDMA 33/ATA 66/ATA 100/ATA 133), allows connection
of 4 IDE devices
FDD Connections 1 FDD connection, allows connection of 2 FDD devices
Onboard SATA 4 Serial ATA ports from SB450 controller
supported on the Win 2000/XP operating systems
Peripherals 1 VGA port, 1 COMA port connection
8 USB 2.0 ports (rear x 4, front x 4 via cable)
1 front audio connector
2 1394 connector (rear x1, front x 1 via cable)
Onboard LAN Onboard RTL8100C chip (10/100 Mbit)
1 RJ 45 port
Onboard Audio ALC880 CODEC
Supports Jack Sensing function
Supports 2 / 4 / 6 / 8 channel audio
Supports Line In; Line Out (Front Speaker Out); MIC; Surround Speaker Out
(Rear Speaker Out); Center/Subwoofer Speaker Out;
Side Speaker Out connection
Supports SPDIF Out connection
AUX In connection
supported on the Win 2000/XP operating systems
I/O Control IT8712

Hardware Installation- 5 -
English
Hardware Monitor System voltage detection
CPU temperature detection
CPU / System fan speed detection
CPU warning temperature
CPU / System fan failure warning
CPU smart fan control
Onboard SATA RAID Onboard SB450 chipset
- supports data striping (RAID 0) or mirroring (RAID 1) function
- supports data transfer rate of up to 150 MB/s
- supports hot plugging function
- supports a maximum of 4 SATA connections
- supported on the Win 2000/XP operating systems
Form Factor Micro ATX form factor; 24.4cm x 24.4cm

K8RS482M-FS-02 Motherboard - 6 -
English
1-2 I/O Back Panel Introduction
COM A (Serial Port)
Connects to serial-based mouse or data processing devices.
VGA Port
Monitor can be connected to VGA port.
OPTICAL (SPDIF Out)
The SPDIF optical output port is capable of providing digital audio to external speakers or com
pressed AC3 data to an external Dolby Digital Decoder via an optical cable.
1394 Connector
Serial interface standard set by Institute of Electrical and Electronics Engineers, which has features
like high speed, highbandwidth and hot plug. Be careful with the polarity of the IEEE1394 connector.
Check the pin assignment carefully while you connect the IEEE1394 cable, incorrect connection
between the cable and connector will make the device unable to work or even damage it. For
optional IEEE1394 cable, please contact your local dealer.
USB port
Before you connect your device(s) into USB connector(s), please make sure your device(s) such
as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface.
Also make sure your OS supports USB controller. If your OS does not support USB controller,
please contact OS vendor for possible patch or driver upgrade. For more information please
contact your OS or device(s) vendors.
LAN Port
The provided Internet connection is fast Ethernet, providing data transfer speeds of 10/100Mbps.
Rear Speaker Out
Connect the rear surround speakers to this connector.
Center/Subwoofer Speaker Out
Connect the Center/Subwoofer speakers to this connector.
Side Speaker Out
Connect the side surround speakers to this connector.
Line In
Devices like CD-ROM, walkman etc. can be connected to Line In jack.
Line Out (Front Speaker Out)
Connect the stereo speakers, earphone or front surround speakers to this connector.
MIC In
Microphone can be connected to MIC In jack.

Hardware Installation- 7 -
English
1-3 Connectors Introduction
1) ATX_12V
2) ATX (Power Connector)
3) CPU_FAN
4) SYS_FAN
5) FDD
6) IDE1 / IDE2
7) S_ATA0 / S_ATA1 / S_ATA2 / S_ATA3
8) F_PANEL
9) AZALIA_FP
10) AUX_IN
11) F_USB1 / F_USB2
12) F2_1394
13) CLR_CMOS
14) BAT
15) TV_OUT
3
5
11
10
6
7
4
1 2
8
9
12 14
15
13

K8RS482M-FS-02 Motherboard - 8 -
English
1/2) ATX_12V/ATX (Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the
components on the motherboard. Before connecting the power connector, please make sure that
all components and devices are properly installed. Align the power connector with its proper
location on the motherboard and connect tightly.
The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power
connector is not connected, the system will not start.
Caution!
Please use a power supply that is able to handle the system voltage requirements. It is
recommended that a power supply that can withstand high power consumption be used (300W or
greater). If a power supply is used that does not provide the required power, the result can lead to
an unstable system or a system that is unable to start.
Pin No. Definition
1 GND
2 GND
3 +12V
4 +12V
Pin No. Definition
1 3.3V
2 3.3V
3 GND
4 +5V
5 GND
6 +5V
7 GND
8 Power Good
9 5V SB(stand by +5V)
10 +12V
11 +12V
12 3.3V(Only for 24pinsATX)
13 3.3V
14 -12V
15 GND
16 PS_ON(soft On/Off)
17 GND
18 GND
19 GND
20 -5V
21 +5V
22 +5V
23 +5V
24 GND
1
4
3
2
1
12
13
24

Hardware Installation- 9 -
English
5) FDD (Floppy Connector)
The FDD connector is used to connect the FDD cable while the other end of the cable connects to the
FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB.
Please connect the red power connector wire to the pin1 position.
1
2
33
34
3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector )
The cooler fan power connector supplies a +12V power voltage via a 3-pin power connector and
possesses a foolproof connection design. Most coolers are designed with color-coded power
connector wires. A red power connector wire indicates a positive connection and requires a
+12V power voltage. The black connector wire is the ground wire (GND).
Please remember to connect the power to the cooler to prevent system overheating and failure.
Caution!
Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.
1
CPU_FAN
SYS_FAN
Pin No. Definition
1GND
2 +12V
3 Sense

K8RS482M-FS-02 Motherboard - 10 -
English
6) IDE1 / IDE2 (IDE Connector)
An IDE device connects to the computer via an IDE connector. One IDE connector can connect to
one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical
drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master
and the other as Slave (for information on settings, please refer to the instructions located on the IDE
device).
17
Pin No. Definition
1 GND
2 TXP
3 TXN
4 GND
5RXN
6 RXP
7 GND
1
2
3940
IDE1 IDE2
7) S_ATA0/S_ATA1/S_ATA2/S_ATA3
Serial ATA can provide 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA
and install the proper driver in order to work properly.