Gigabyte GA-WRX80-SU8-IPMI User manual

GA-WRX80-SU8-IPMI
User's Manual
Rev. 1001

Copyright
©2021 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specications and features in this manual may be made by GIGABYTE without
prior notice.
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form
or by any means without GIGABYTE's prior written permission.
For product-related information, check on our website at: https://www.gigabyte.com

- 4 -
Table of Contents
GA-WRX80-SU8-IPMI Motherboard Layout....................................................................5
GA-WRX80-SU8-IPMI Motherboard Block Diagram .......................................................7
Chapter 1 Hardware Installation .....................................................................................8
1-1 Installation Precautions.................................................................................... 8
1-2 Product Specications...................................................................................... 9
1-3 Installing the CPU .......................................................................................... 11
1-4 Installing the Memory..................................................................................... 12
1-5 Back Panel Connectors.................................................................................. 13
1-6 Internal Connectors........................................................................................ 15
Chapter 2 BIOS Setup ..................................................................................................25
2-1 Startup Screen ............................................................................................... 25
2-2 Main ............................................................................................................... 26
2-3 Advanced ....................................................................................................... 27
2-4 PBS................................................................................................................ 33
2-5 Chipset........................................................................................................... 34
2-6 Server Mgmt................................................................................................... 35
2-7 Security .......................................................................................................... 38
2-8 Boot................................................................................................................ 39
2-9 Save & Exit..................................................................................................... 41
Chapter 3 Application....................................................................................................42
Regulatory Notices.................................................................................................... 52
Contact Us ................................................................................................................ 53

- 5 -
GA-WRX80-SU8-IPMI Motherboard Layout
1 BMC_VGA
2BMC_WATCHD
3 COM2
4 SMB_IPMB
5 I_SGPIO1
6 I_SGPIO2
7 TPM
8 SL_CN1/CN2
9 SL_CN3
10 FUSB30_1/2
11 FUSB2
12 F_USB32C
13 USB30V
14 PMBUS
15 CLR_CMOS
16 CI
17 F_PANEL
18 CPU_FAN1
19 SYS_FAN1~6
20 ATX_CPU
21 ATX_PCIE
22 ATX
23 P_X4_M2_A
24 P_X4_M2_B
25 SATA_0_1
26 SATA_2_3
27 BAT
28 F_AUDIO
29 SPEAKER
30 TBT
31 PWR_SW
32 RST_SW
33 QF_SW
34 F_LED1
35 BMC_LED1
28
2
19
10
3
4
5
6
7
11
13
30
17 31 33 2120 221423 192526 8 9
16
12
24
18
19
1
29
32
34
35
27
15

- 6 -
Box Contents
5GA-WRX80-SU8-IPMI motherboard
5Motherboard driver disc 5Four SATA cables
5Quick Installation Guide 5I/O Shield

GA-WRX80-SU8-IPMI Motherboard Block Diagram
86%
86%
)URQW86%7\SH&


ZLWK86%*HQVXSSRUW
5HDU86%*HQ7\SH$
)URQW86%*HQ7\SH$
9HUWLFDO
)URQW86%*HQ7\SH$
)URQW86%7\SH$
6$7$*EV
*E(/$1
*E(/$1
*E(/$1
5HDOWHN
$/&
86%&2'(&
5HDOWHN
$/&9%
9*$
&20
&20
$XGLR-DFNV

63',)2XW
6RFNHW63
$0'6HULHV
3UHPLXP&KLS
&KDQQHO''5
',00SHUFKDQQHO
6SHHGXSWR0+]
',00$
',00%
',00&
',00'
',00(
',00)
',00*
',00+
6ORW3&,H[
6ORW3&,H[
6ORW3&,H[
6ORW3&,H[
6ORW3&,H[
6ORW3&,H[
6ORW3&,H[
3&,H*HQ[
3&,H*HQ[
3&,H*HQ[
3&,H*HQ[
3&,H[ 3&,H[
3&,H[
3&,H*HQ
06RFNHW
3&,H6$7$
6$7$*3,2
6OLP6$6
3&,H
6OLP6$6
3&,H6$7$
5HDU86%7\SH&


ZLWK86%*HQVXSSRUW
5HDU86%*HQ7\SH$
PCIE UPLINK PCIEX8
$63(('
$67
%0&
,QWHO
,1&6,
,QWHO
,1&6,
,QWHO
;
- 7 -

Chapter 1 Hardware Installation
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become
damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's
manual and follow these procedures:
•Prior to installation, make sure the chassis is suitable for the motherboard.
•Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
•Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
•When connecting hardware components to the internal connectors on the motherboard, make
sure they are connected tightly and securely.
•When handling the motherboard, avoid touching any metal leads or connectors.
•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,
keep your hands dry and rst touch a metal object to eliminate static electricity.
•Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
•Before connecting or unplugging the power supply cable from the motherboard, make sure
the power supply has been turned off.
•Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
•Before using the product, please verify that all cables and power connectors of your hardware
components are connected.
•To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
•Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
•Do not place the computer system on an uneven surface.
•Do not place the computer system in a high-temperature or wet environment.
•Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
•If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certied computer technician.
•If you use an adapter, extension power cable, or power strip, ensure to consult with its installation
and/or grounding instructions.
- 8 -

1-2 ProductSpecications
CPU AMD Ryzen™Threadripper™PRO 3000WX (up to 64C)
Single sWRX8 4094 socket; CPU TDP supports up to 280W
Chipset AMD WRX80 Chipset
Memory 8 x DDR4 DIMM sockets supporting up to 1 TB of system memory
8 channels memory architecture (1 DIMM per channel)
Support up to DDR4 3200/2933/2600 MHz
Support for ECC RDIMM 3DS memory modules
Onboard
Graphics 1 x D-Sub port, supporting a maximum resolution of 1920x1200@60 Hz
Audio Realtek®ALC1220-VB CODEC
High Denition Audio
2/4/5.1/7.1-channel
Support for S/PDIF Out
LAN Dual Intel®X550 10 GbE LAN
Dual Intel®i210AT GbE LAN (NCSI MLAN)
Expansion Slots (Slot7) PCIe x16 (running at Gen 4 x16)
(Slot6) PCIe x16 (running at Gen 4 x16)
(Slot5) PCIe x16 (running at Gen 4 x16)
(Slot4) PCIe x16 (running at Gen 4 x16)
(Slot3) PCIe x16 (running at Gen 4 x16)
(Slot2) PCIe x16 (running at Gen 4 x8)
(Slot1) PCIe x16 (running at Gen 4 x16)
Storage Interface 4 x SATA 6Gb/s connectors (support for software RAID 0, RAID1, RAID5, and
RAID10)
2 x M.2 connectors (Socket 3, M key, type 2242/2280, supporting PCIe Gen 4
x4 or SATA mode)
2 x slimSAS (PCIe Gen 4 x4 or 4x SATAIII) + 1 x slimSAS (PCIe Gen 4 x4)
connectors
USB 1 x USB Type-C®port on the back panel, with USB 3.2 Gen 2 support
5 x USB 3.2 Gen 2 Type-A ports (red) on the back panel
1 x USB Type-C®header onboard, with USB 3.2 Gen 2 support
2 x USB 3.2 Gen 1 header onboard
1 x USB 3.2 Gen 1 vertical connector onboard
1 x USB 2.0 header on board
Internal
Connectors
1 x 24-pin ATX main power connector
1 x 8-pin ATX 12V CPU power connector
1 x 8-pin ATX 12V GPU power connector
1 x CPU fan header
6 x system fan headers
4 x SATA 6Gb/s connectors
2 x M.2 Socket 3 connectors
3 x slimSAS connectors
1 x front panel header
1 x front panel audio header
- 9 -

Internal
Connectors
1 x USB Type-C®header, with USB 3.2 Gen 2 support
1 x USB 3.2 Gen 1 vertical connector
2 x USB 3.2 Gen 1 header
1 x USB 2.0 header
1 x Thunderbolt™add-in card connector
1 x Trusted Platform Module(TPM) header (2x6 pin, for the GC-TPM2.0_S
module only)
1 x serial port header
1 x chassis intrusion header
1 x Clear CMOS jumper
2 x SATA SGPIO headers
1 x BMC_VGA jumper
1 x BMC_WATCHD jumper
1 x SMB_IPMB connector
1 x PMBUS header
1 x Speaker
Back Panel
Connectors
1 x D-sub port
1 x serial port
1 x USB 3.2 Gen 2 Type-C port (red)
5 x USB 3.2 Gen 2 Type-A port (red)
2 x GbE RJ-45 ports
2 x 10GbE RJ-45 ports
1 x optical S/PDIF Out connector
5 x audio jacks
I/O Controller ASPEED®AST2500 BMC chip
Hardware
Monitor
Voltage detection
Temperature detection
Fan speed detection
Fan speed control
* Whether the fan speed control function is supported will depend on the fan you install.
Operating
Properties
Operating temperature: 10°C to 40°C
Operating humidity: 8 - 80%
Non-operating temperature: -40°C to 70°C
Non-operating humidity: 5% - 95%
Form Factor CEB Form Factor; 30.5cm x 26.7cm
Operating
System
Windows 10
Linux
* GIGABYTE reserves the right to make any changes to the product specications and product-related information
without prior notice.
- 10 -

1-3 Installing the CPU
Read the following guidelines before you begin to install the CPU:
•Make sure that the motherboard supports the CPU.
•Always turn off the computer and unplug the power cord from the power outlet before installing the
CPU to prevent hardware damage.
•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
•Apply an even and thin layer of thermal grease on the surface of the CPU.
•Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
of the CPU may occur.
•Set the CPU host frequency in accordance with the CPU specications. It is not recommended
that the system bus frequency be set beyond hardware specications since it does not meet the
standard requirements for the peripherals. If you wish to set the frequency beyond the standard
specications, please do so according to your hardware specications including the CPU, graphics
card, memory, hard drive, etc.
3
1
2
1
External cap
2
3
CPU
4
5
67
1
3
2
8
3
1
2
4
- 11 -
Installing the CPU
Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

Due to CPU limitations, read the following guidelines before installing the memory in 8 Channel mode.
When enabling 8 Channel mode with eight memory modules, it is recommended that memory of the same
capacity, brand, speed, and chips be used.
4ChannelMemoryConguration
This motherboard supports 8 Channel Technology. After the memory is installed, the BIOS will automatically
detect the specications and capacity of the memory.
The eight DDR4 memory sockets are divided into eight channels and each channel has one memory socket
as following:
Channel 1: P1-DIMM_A1
Channel 2: P1-DIMM_B1
Channel 3: P1-DIMM_D1
Channel 4: P1-DIMM_D1
Channel 5: P1-DIMM_E1
Channel 6: P1-DIMM_F1
Channel 7: P1-DIMM_G1
Channel 8: P1-DIMM_H1
1-4 Installing the Memory
Read the following guidelines before you begin to install the memory:
•Make sure that the motherboard supports the memory. It is recommended that memory of the same
capacity, brand, speed, and chips be used.
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
•Always turn off the computer and unplug the power cord from the power outlet before installing the
memory to prevent hardware damage.
•Memory modules have a foolproof design. A memory module can be installed in only one direction.
If you are unable to insert the memory, switch the direction.
- 12 -

1-5 Back Panel Connectors
D-Sub Port
The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200@60 Hz
(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports
D-Sub connection to this port.
COM Port
Use this port to connect devices such as a mouse, modem or other peripherals.
USB 3.2 Gen 2 Type-A Port (Red)
The USB 3.2 Gen 2 Type-A port supports the USB 3.2 Gen 2 specication and is compatible to the USB
3.2 Gen 1 and USB 2.0 specication. Use this port for USB devices.
USB Type-C®Port
The reversible USB port supports the USB 3.2 Gen 2x2 specication and is compatible to the USB 3.2
Gen 2, USB 3.2 Gen 1, and USB 2.0 specications. Use this port for USB devices.
GbE LAN Port (LAN1~2)
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.
•When removing the cable connected to a back panel connector, rst remove the cable from your
device and then remove it from the motherboard.
•When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.
Link LEDActivity LED
LAN Port
LED State Description
Link (Right) Solid Green 100 Mbps data rate
Solid Amber 1 Gbps data rate
Activity (Left) Blinking Yellow Active
Link LEDActivity LED
10 GbE LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 10 Gbps data rate. The following
describes the states of the LAN port LEDs.
LED State Description
Link (Right) Solid Amber 10 Gbps data rate
Solid Green 1 Gbps data rate
Activity (Left) Blinking Yellow Active
Activity LEDLink LED
- 13 -

Center/Subwoofer Speaker Out
Use this audio jack to connect center/subwoofer speakers.
Rear Speaker Out
Use this audio jack to connect rear speakers.
Optical S/PDIF Out Connector
This connector provides digital audio out to an external audio system that supports digital optical audio.
Before using this feature, ensure that your audio system provides an optical digital audio in connector.
Line In/Side Speaker Out
The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out/Front Speaker Out
The line out jack. This jack supports audio amplifying function. For better sound quality, it is recommended
that you connect your headphone/speaker to this jack (actual effects may vary by the device being used).
Mic In
The Mic in jack.
•If you want to install a Side Speaker, you need to retask the Line in jack to be Side Speaker
out through the audio driver.
•To enable or congure the audio amplifying function for the Line out jack, please access the
Realtek Audio Console application.
Audio Jack Congurations:
Jack Headphone/
2-channel 4-channel 5.1-channel 7.1-channel
Center/Subwoofer Speaker Out a a
Rear Speaker Out aaa
Line In/Side Speaker Out a
Line Out/Front Speaker Out aaaa
Mic In a
- 14 -

1-6 Internal Connectors
Read the following guidelines before connecting external devices:
•First make sure your devices are compliant with the connectors you wish to connect.
•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
•After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
- 15 -
28
2
19
10
3
4
5
6
7
11
13
30
17 31 33 2120 221423 192526 8 9
16
12
24
18
19
1
29
32
34
35
27
15
1 BMC_VGA
2BMC_WATCHD
3 COM2
4 SMB_IPMB
5 I_SGPIO1
6 I_SGPIO2
7 TPM
8 SL_CN1/CN2
9 SL_CN3
10 FUSB30_1/2
11 FUSB2
12 F_USB32C
13 USB30V
14 PMBUS
15 CLR_CMOS
16 CI
17 F_PANEL
18 CPU_FAN1
19 SYS_FAN1~6
20 ATX_CPU
21 ATX_PCIE
22 ATX
23 P_X4_M2_A
24 P_X4_M2_B
25 SATA_0_1
26 SATA_2_3
27 BAT
28 F_AUDIO
29 SPEAKER
30 TBT
31 PWR_SW
32 RST_SW
33 QF_SW
34 F_LED1
35 BMC_LED1

1) BMC_VGA
2) BMC_WATCHD
Pin Denition
1-2 Enable (Default)
2-3 Disable
Pin Denition
1-2 Enable
2-3 Disable (Default)
Pin Denition Pin Denition
1 NDCD- 2 NSIN
3 NSOUT 4 NDTR-
5 GND 6 NDSR-
7 NRTS- 8 NCTS-
9 NRI- 10 -
9
1
10
2
3) COM2 (Serial Port Header)
4) SMB_IPMB
Pin Denition
1 SMB_DATA
2 GND
3 SMB_CLK
4 NA
1
- 16 -
1
1

8) SL_CN1/SL_CN2
5) I_SGPIO1 (For SATA_0_1)
6) I_SGPIO2 (For SATA_2_3)
Pin Denition Pin Denition
1 NA 2 -
3SATA_DATA 4 GND
5 GND 6 SATA_LOAD
7 NA 8 SATA_CLK
2
8
1
7
7) TPM (Trusted Platform Module/Port 80 Header)
Pin Denition Pin Denition
1 LPC_IO0 2 P3V3
3 LPC_IO1 4 -
5 LPC_IO2 6 TPM_CLK
7 LPC_IO3 8 GND
9 LFRAME# 10 NA
11 SERIRQ 12 TPM_RST
2
12
1
11
B19B1
A19A1
A19A1
B19B1
Pin Denition Pin Denition
B1 GND A1 GND
B2 Tx0+/SATA1_TX+ A2 Rx0+/SATA1_RX+
B3 Tx0-/SATA1_TX- A3 Rx0-/SATA1_RX-
B4 GND A4 GND
B5 Tx1+/SATA2_TX+ A5 Rx1+/SATA2_RX+
B6 Tx1-/SATA2_TX- A6 Rx1-/SATA2_RX-
B7 GND A7 GND
B8 SB0 A8 SB7
B9 SB1 A9 SB4
B10 SB2 A10 SB3
B11 SB5 A11 Clock+
B12 SB6 A12 Clock-
B13 GND A13 GND
B14 Tx2+/SATA3_TX+ A14 Rx2+/SATA3_RX+
B15 Tx2-/SATA3_TX- A15 Rx2-/SATA3_RX-
B16 GND A16 GND
B17 Tx3+/SATA4_TX+ A17 Rx3+/SATA4_RX+
B18 Tx3-/SATA4_TX- A18 Rx3-/SATA4_RX-
B19 GND A19 GND
- 17 -

9) SL_CN3
B19B1
A19A1
A19A1
B19B1
Pin Denition Pin Denition
B1 GND A1 GND
B2 Tx0+ A2 Rx0+
B3 Tx0- A3 Rx0-
B4 GND A4 GND
B5 Tx1+ A5 Rx1+
B6 Tx1- A6 Rx1-
B7 GND A7 GND
B8 SB0 A8 SB7
B9 SB1 A9 SB3
B10 SB8 A10 SB9
B11 SB2 A11 SB4
B12 SB6 A12 SB5
B13 GND A13 GND
B14 Tx2+ A14 Rx2+
B15 Tx2- A15 Rx2-
B16 GND A16 GND
B17 Tx3+ A17 Rx3+
B18 Tx3- A18 Rx3-
B19 GND A19 GND
10) FUSB30_1/FUSB30_2 (USB 3.2 Gen 1 Headers)
1
10
20
11
Pin Denition Pin Denition
1 VBUS 11 D2+
2 SSRX1- 12 D2-
3 SSRX1+ 13 GND
4 GND 14 SSTX2+
5 SSTX1- 15 SSTX2-
6 SSTX1+ 16 GND
7 GND 17 SSRX2+
8 D1- 18 SSRX2-
9 D1+ 19 VBUS
10 NC 20 -
- 18 -

11) FUSB2 (USB 2.0/1.1 Header)
12) F_USB32C (USB Type-C®Header with USB 3.2 Gen 2 Support)
Pin Denition Pin Denition
1 Power (5V) 2 Power (5V)
3 USB DX- 4 USB DY-
5 USB DX+ 6 USB DY+
7 GND 8 GND
9 - 10 NC
9
1
10
2
1
10
20
11
Pin Denition Pin Denition
1 VBUS 11 VBUS
2 TX1+ 12 TX2+
3 TX1- 13 TX2-
4 GND 14 GND
5 RX1+ 15 RX2+
6 RX1- 16 RX2-
7 VBUS 17 GND
8 CC1 18 D-
9 SBU1 19 D+
10 SBU2 20 CC2
13) USB30V (USB 3.2 Gen 1 Connector)
Pin Denition
1 SMB_CLK
2 SMB_DATA
3 PSU_ALERT
4 GND
5 P3V3
1
14) PMBUS (Power supply I2C Connector)
- 19 -

17) F_PANEL
24
23
2
1
Pin Denition Pin Denition
1 Power LED+ 2 5V Standby
3 - 4 ID LED+
5 Power LED- 6 ID LED-
7 HDD LED+ 8 System Status LED+
9 HDD LED1 10 System Status LED-
11 Power Button 12 LAN1 Active LED+
13 GND 14 LAN1 Link LED-
15 Reset Button 16 SMBus Data
17 GND 18 SMBus Clock
19 ID Button 20 Case Open
21 GND 22 LAN2 Active LED+
23 NMI Switch 24 LAN2 Link LED-
Pin Denition
1-2 NA (Default)
2-3 Clear CMOS
1
15) CLR_CMOS
Pin Denition
1 Intrusion Input
2 GND
1
16) CI
- 20 -