Gigabyte GA-Z97P-D3 User manual
GA-Z97P-D3
User's Manual
Rev. 1001
12ME-Z97PD3-1001R
Copyright
©2014 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by
any means without GIGABYTE's prior written permission.
In order to assist in the use of this product, carefully read the User's Manual.
For product-related information, check on our website at: http://www.gigabyte.com
Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the
revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS,
drivers, or when looking for technical information.
Example:
Motherboard
GA-Z97P-D3
Apr. 10, 2014
Apr. 10, 2014
Motherboard
GA-Z97P-D3
- 3 -
Table of Contents
GA-Z97P-D3 Motherboard Layout...................................................................................4
GA-Z97P-D3 Motherboard Block Diagram......................................................................5
Chapter 1 Hardware Installation .....................................................................................6
1-1 Installation Precautions.................................................................................... 6
...................................................................................... 7
1-3 Installing the CPU ............................................................................................ 9
1-4 Installing the Memory..................................................................................... 10
1-5 Installing an Expansion Card ......................................................................... 10
1-6 Back Panel Connectors.................................................................................. 10
1-7 Internal Connectors........................................................................................ 12
Chapter 2 BIOS Setup ..................................................................................................17
2-1 Startup Screen ............................................................................................... 18
2-2 M.I.T. .............................................................................................................. 18
2-3 System Information ........................................................................................ 24
2-4 BIOS Features ............................................................................................... 25
2-5 Peripherals..................................................................................................... 28
2-6 Power Management....................................................................................... 31
2-7 Save & Exit..................................................................................................... 33
Chapter 3 Appendix ......................................................................................................34
..................................................................... 34
3-2 Drivers Installation.......................................................................................... 36
Regulatory Statements.............................................................................................. 37
Contact Us ................................................................................................................ 40
- 4 -
GA-Z97P-D3 Motherboard Layout
The box contents above are for reference only and the actual items shall depend on the product package you obtain.
The box contents are subject to change without notice.
Box Contents
5GA-Z97P-D3 motherboard
5Motherboard driver disk 5Two SATA cables
5User's Manual 5I/O Shield
KB_MS CPU_FAN
LGA1150
ATX
F_USB30
AUDIO
DDR3_4
DDR3_2
DDR3_3
DDR3_1
BAT
ATX_12V_2X4
Intel®Z97
CODEC
CLR_CMOS
M_BIOS
B_BIOS
COMA
HDMI
USB_LAN
Realtek®
GbE LAN PCIEX16
PCIEX1_1
PCIEX4
SYS_FAN1
SYS_FAN3
iTE®
Super I/O PCIe to PCI
Bridge
GA-Z97P-D3
R_USB
R_USB30
F_USB1F_PANEL F_USB2
F_AUDIO
SPDIF_O LPTCOMB F_USB3
SYS_FAN2
PCI1
PCI2
SATA3
5 3 1
4 2 0
PCIEX1_2
- 5 -
GA-Z97P-D3 Motherboard Block Diagram
PS/2 KB/Mouse
iTE®
Super I/O
Intel®Z97
PCI Express Bus
LAN
RJ45
Realtek®
GbE LAN
10 USB 2.0/1.1
4 USB 3.0/2.0
Dual BIOS
6 SATA 6Gb/s
x1
DMI 2.0
FDI
HDMI
x4
1 PCI Express x4
PCI Express Bus
PCIe CLK
PCI CLK
x16
1 PCI Express x16
2 PCI
PCIe to PCI
Bridge
x1
LPC
Bus
CODEC
S/PDIF Out
COM
LPT
2 PCI Express x1
x1x1
Dual Channel Memory
LGA1150 CPU
- 6 -
Chapter 1 Hardware Installation
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become
manual and follow these procedures:
•Prior to installation, make sure the chassis is suitable for the motherboard.
•
warranty sticker provided by your dealer. These stickers are required for warranty validation.
•Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
•When connecting hardware components to the internal connectors on the motherboard, make
sure they are connected tightly and securely.
•When handling the motherboard, avoid touching any metal leads or connectors.
•
components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,
•Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
•Before unplugging the power supply cable from the motherboard, make sure the power supply
has been turned off.
•Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
•Before using the product, please verify that all cables and power connectors of your hardware
components are connected.
•To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
•Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
•Do not place the computer system on an uneven surface.
•Do not place the computer system in a high-temperature environment.
•Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
•If you are uncertain about any installation steps or have a problem related to the use of the
- 7 -
CPU Support for Intel®Core™i7 processors/Intel®Core™i5 processors/
Intel®Core™i3 processors/Intel®Pentium®processors/Intel®Celeron®processors
in the LGA1150 package
L3 cache varies with CPU
Chipset Intel®Z97 Express Chipset
Memory 4 x DDR3 DIMM sockets supporting up to 32 GB of system memory
* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical
the physical memory installed.
Dual channel memory architecture
Support for non-ECC memory modules
Onboard
Graphics
Integrated Graphics Processor:
* Support for HDMI 1.4a version.
- Maximum shared memory of 1 GB
Audio Realtek®ALC887 codec
2/4/5.1/7.1-channel
and enable the multi-channel audio feature through the audio driver.
Support for S/PDIF Out
LAN Realtek®
Expansion Slots
* For optimum performance, if only one PCI Express graphics card is to be installed,
be sure to install it in the PCIEX16 slot.
2 x PCI Express x1 slots
2 x PCI slots
Multi-Graphics
Technology Support for 2-Way AMD CrossFire™technology
Storage Interface Chipset:
- 6 x SATA 6Gb/s connectors
- Support for RAID 0, RAID 1, RAID 5, and RAID 10
USB Chipset:
- 8 -
Internal
Connectors
1 x 24-pin ATX main power connector
1 x 8-pin ATX 12V power connector
1 x CPU fan header
3 x system fan headers
1 x front panel header
1 x front panel audio header
1 x S/PDIF Out header
6 x SATA 6Gb/s connectors
1 x USB 3.0/2.0 header
3 x USB 2.0/1.1 headers
1 x serial port header
1 x parallel port header
1 x Clear CMOS jumper
Back Panel
Connectors
1 x PS/2 keyboard port
1 x PS/2 mouse port
1 x serial port
1 x HDMI port
2 x USB 3.0/2.0 ports
4 x USB 2.0/1.1 ports
1 x RJ-45 port
I/O Controller iTE®I/O Controller Chip
Hardware
Monitor
System voltage detection
CPU/System temperature detection
CPU/System fan speed detection
CPU/System overheating warning
CPU/System fan fail warning
CPU/System fan speed control
* Whether the fan speed control function is supported will depend on the cooler you
install.
BIOS
Use of licensed AMI UEFI BIOS
Support for DualBIOS™
PnP 1.0a, DMI 2.7, SM BIOS 2.7, ACPI 2.0
Unique Features Support for APP Center
* Available applications in APP Center may differ by motherboard model. Supported
- @BIOS
- EasyTune
- EZ Setup
- Fast Boot
- ON/OFF Charge
- Smart TimeLock
- Smart Recovery 2
- System Information Viewer
- USB Blocker
Support for Q-Flash
- 9 -
1-3 Installing the CPU
Read the following guidelines before you begin to install the CPU:
•Make sure that the motherboard supports the CPU.
•Always turn off the computer and unplug the power cord from the power outlet before installing the
CPU to prevent hardware damage.
•
•Apply an even and thin layer of thermal grease on the surface of the CPU.
•Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
of the CPU may occur.
•
standard requirements for the peripherals. If you wish to set the frequency beyond the standard
card, memory, hard drive, etc.
Installing the CPU
Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.
Notch
Alignment KeyAlignment Key Notch
LGA1150 CPU
LGA1150 CPU Socket
Pin One Corner of the CPU Socket Triangle Pin One Marking on the CPU
Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load plate
automatically during the process of re-engaging the lever after you insert the CPU.
Unique Features Support for Smart Switch
Support for Xpress Install
Bundled
Software
Norton®
Intel®Rapid Start Technology
Intel®Smart Connect Technology
Intel®Smart Response Technology
Operating
System Support for Windows 8.1/8/7
Form Factor ATX Form Factor; 30.5cm x 20cm
prior notice.
* Please visit the Support & Downloads\Utility
for the software listed in the "Unique Features" and "Bundled Software" columns.
- 10 -
1-5 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card:
•Make sure the motherboard supports the expansion card. Carefully read the manual that came
with your expansion card.
•Always turn off the computer and unplug the power cord from the power outlet before installing an
expansion card to prevent hardware damage.
1-6 Back Panel Connectors
Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1. Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.
2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory
of the same capacity, brand, speed, and chips be used and installed in the same colored DDR3
sockets. For optimum performance, when enabling Dual Channel mode with two memory modules,
we recommend that you install them in the DDR3_1 and DDR3_2 sockets.
This motherboard provides four DDR3 memory sockets and supports Dual Channel Technology. After the
Dual Channel memory mode will double the original memory bandwidth.
The four DDR3 memory sockets are divided into two channels and each channel has two memory socket as
following:
Channel A: DDR3_2, DDR3_4
Channel B: DDR3_1, DDR3_3
PS/2 Keyboard and PS/2 Mouse Port
Serial Port
Use the serial port to connect devices such as a mouse, modem or other peripherals.
1-4 Installing the Memory
Read the following guidelines before you begin to install the memory:
•Make sure that the motherboard supports the memory. It is recommended that memory of the
same capacity, brand, speed, and chips be used.
•Always turn off the computer and unplug the power cord from the power outlet before installing the
memory to prevent hardware damage.
•Memory modules have a foolproof design. A memory module can be installed in only one direction.
If you are unable to insert the memory, switch the direction.
- 11 -
multi-channel audio feature through the audio driver.
•
device and then remove it from the motherboard.
•When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent
an electrical short inside the cable connector.
Activity LED
Connection/
Speed LED
LAN Port
Activity LED:Connection/Speed LED:
State Description
Orange 1 Gbps data rate
Green 100 Mbps data rate
Off 10 Mbps data rate
State Description
Blinking Data transmission or receiving is occurring
Off No data transmission or receiving is occurring
HDMI Port
The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD
audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported
dependent on the monitor being used.
Line In Jack (Blue)
The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out Jack (Green)
The line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to
Mic In Jack (Pink)
The Mic in jack. Microphones must be connected to this jack.
After installing the HDMI device, make sure to set the default sound playback device to HDMI.
USB 2.0/1.1 Port
USB 3.0/2.0 Port
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.
- 12 -
1-7 Internal Connectors
Read the following guidelines before connecting external devices:
•First make sure your devices are compliant with the connectors you wish to connect.
•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
•After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
1) ATX_12V_2X4
2) ATX
3) CPU_FAN
4) SYS_FAN1/SYS_FAN2/SYS_FAN3
5) SATA3 0/1/2/3/4/5
6) F_PANEL
7) F_AUDIO
8) SPDIF_O
9) F_USB30
10) F_USB1/2/3
11) COMB
12) LPT
13) BAT
14) CLR_CMOS
1 3
9
2
4
14
7 10 10
13
4
5
12118 6
- 13 -
1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components
off and all devices are properly installed. The power connector possesses a foolproof design. Connect the
power supply cable to the power connector in the correct orientation.
The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,
the computer will not start.
3/4) CPU_FAN/SYS_FAN1/SYS_FAN2/SYS_FAN3 (Fan Headers)
The speed control function requires the use of a fan with fan speed control design. For optimum heat
dissipation, it is recommended that a system fan be installed inside the chassis.
To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption
lead to an unstable or unbootable system.
ATX_12V_2X4:
G.QBOFM
131
2412
ATX
ATX:
Pin No. Pin No.
1 3.3V 13 3.3V
2 3.3V 14 -12V
3 GND 15 GND
4 +5V 16
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 Power Good 20 -5V
9 21 +5V
10 +12V 22 +5V
11
23
12
24
•Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating
may result in damage to the CPU or the system may hang.
•
G.QBOFM
ATX_12V_2X4
5 8
1 4
Pin No. Pin No.
1 5 +12V
2 6 +12V
3 GND 7 +12V
4 GND 8 +12V
CPU_FAN
G.QBOFM
1
SYS_FAN1/2
G.QBOFM
1
CPU_FAN:
Pin No.
1 GND
2 +12V
3 Sense
4 Speed Control
SYS_FAN1/SYS_FAN2:
Pin No.
1 GND
2 +12V / Speed Control
3 Sense
4 VCC
SYS_FAN3:
Pin No.
1 GND
2 +12V
3 N/A
SYS_FAN3
1
- 14 -
5) SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s
standard. Each SATA connector supports a single SATA device. The Intel
®
Chipset supports RAID 0, RAID 1,
RAID array.
Pin No.
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
SATA3
1 0
3 2
5 4
G.QBOFM
G.QBOFM
G.QBOFM
G.QBOFM
G.QBOFM
G.QBOFM
71
7
7
1
1
6) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, and system status indicator on the chassis to this header
according to the pin assignments below. Note the positive and negative pins before connecting the cables.
•PW
•SPEAK
Connects to the speaker on the chassis front panel. The system reports system
startup status by issuing a beep code. One single short beep will be heard if no
problem is detected at system startup.
•PLED/PWR
System Status LED
S0 On
S3/S4/S5 Off
Connects to the power status indicator on the
chassis front panel. The LED is on when the system
is operating. The LED is off when the system is in
The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch,
power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this
header, make sure the wire assignments and the pin assignments are matched correctly.
Power LED
G.QBOFM
1
2
19
20
CI-
CI+
PWR_LED+
PLED-
PW-
SPEAK+
SPEAK-
PLED+
PW+
Power LED
HD-
RES+
HD+
RES-
Hard Drive
Activity LED
Reset
Switch Chassis Intrusion
Header
Power Switch Speaker
PWR_LED-
PWR_LED-
•HD
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing
data.
•RES
and fails to perform a normal restart.
•CI
Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been removed. This
function requires a chassis with a chassis intrusion switch/sensor.
•
used, the total number of hard drives must be an even number.
•
•
•
for more information.
- 15 -
7) F_AUDIO (Front Panel Audio Header)
The front panel audio header supports Intel®
your chassis front panel audio module to this header. Make sure the wire assignments of the module
connector match the pin assignments of the motherboard header. Incorrect connection between the module
connector and the motherboard header will make the device unable to work or even damage it.
For HD Front Panel Audio: ForAC'97 Front Panel Audio:
Pin No.
1 MIC2_L
2 GND
3 MIC2_R
4 -ACZ_DET
5 LINE2_R
6 GND
7 FAUDIO_JD
8 No Pin
9 LINE2_L
10 GND
Pin No.
1 MIC
2 GND
3 MIC Power
4 NC
5
6 NC
7 NC
8 No Pin
9
10 NC
•The front panel audio header supports HD audio by default.
•Audio signals will be present on both of the front and back panel audio connections simultaneously.
•Some chassis provide a front panel audio module that has separated connectors on each wire instead of a
single plug. For information about connecting the front panel audio module that has different wire assignments,
please contact the chassis manufacturer.
9 1
10 2
8) SPDIF_O (S/PDIF Out Header)
sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for
digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display
to the graphics card and have digital audio output from the HDMI display at the same time.
For information about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion
card.
1
Pin No.
1 SPDIFO
2 GND
9) F_USB30 (USB 3.0/2.0 Header)
optional 3.5" front panel that provides two USB 3.0/2.0 ports, please contact the local dealer.
Pin No. Pin No. Pin No.
1VBUS 8D1- 15 SSTX2-
2SSRX1- 9D1+ 16 GND
3SSRX1+ 10 NC 17 SSRX2+
4GND 11 D2+ 18 SSRX2-
5SSTX1- 12 D2- 19 VBUS
6SSTX1+ 13 GND 20 No Pin
7GND 14 SSTX2+
10
20 1
11
Prior to installing the USB front panel, be sure to turn off your computer and unplug the power cord from the power
outlet to prevent damage to the USB front panel.
- 16 -
10) F_USB1/2/3 (USB 2.0/1.1 Headers)
optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.
Pin No. Pin No.
1 6 USB DY+
2 7 GND
3 USB DX- 8 GND
4 USB DY- 9 No Pin
5 USB DX+ 10 NC
•
•Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power
outlet to prevent damage to the USB bracket.
G.QBOFM
10
9
2
1
11) COMB (Serial Port Header)
The COM header can provide one serial port via an optional COM port cable. For purchasing the optional
COM port cable, please contact the local dealer.
Pin No. Pin No.
1 NDCD- 6 NDSR-
2 NSIN 7 NRTS-
3 NSOUT 8 NCTS-
4 NDTR- 9 NRI-
5 GND 10 No Pin
10
9
2
1
12) LPT (Parallel Port Header)
The LPT header can provide one parallel port via an optional LPT port cable. For purchasing the optional
LPT port cable, please contact the local dealer.
Pin No. Pin No. Pin No.
1STB- 10 GND 19 ACK-
2AFD- 11 PD4 20 GND
3PD0 12 GND 21 BUSY
4ERR- 13 PD5 22 GND
5PD1 14 GND 23 PE
6INIT- 15 PD6 24 No Pin
7PD2 16 GND 25 SLCT
8SLIN- 17 PD7 26 GND
9PD3 18 GND
26
25
2
1
G.QBOFM
- 17 -
Chapter 2 BIOS Setup
•
may result in system malfunction.
•
unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to
saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to
To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.
To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.
•Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.
•@BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet
and updates the BIOS.
14) CLR_CMOS (Clear CMOS Jumper)
the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.
•Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values.
•
Open: Normal
Short: Clear CMOS Values
13) BAT (Battery)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low
level, or the CMOS values may not be accurate or may be lost.
You may clear the CMOS values by removing the battery:
1. Turn off your computer and unplug the power cord.
2.
object like a screwdriver to touch the positive and negative terminals of the battery holder,
3. Replace the battery.
4. Plug in the power cord and restart your computer.
•Always turn off your computer and unplug the power cord before replacing the battery.
•Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model.
•Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain
about the battery model.
•
•Used batteries must be handled in accordance with local environmental regulations.
- 18 -
2-1 Startup Screen
The following startup Logo screen will appear when the computer boots.
2-2 M.I.T.
This section provides information on the BIOS version, CPU base clock, CPU frequency, memory frequency,
•When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.
•The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.
There are three different BIOS modes as follows and you can use the <F2> key to switch between these modes. The
quickly and easily. The ST Mode provides a fancy and user-friendly BIOS environment where users can easily point
and click through various settings and make adjustments for optimum performance. Classic Setup is the conventional
BIOS Setup interface where you can press the arrow keys on your keyboard to move among the items and press
<Enter> to accept or enter a sub-menu. Or you can use your mouse to select the item you want.
Function Keys
- 19 -
`M.I.T. Current Status
This screen provides information on CPU/memory frequencies/parameters.
Intel®CPUs' unique features, please visit Intel's website.
&Performance Upgrade (Note)
&CPU Base Clock
Important: It is highly recommended that the CPU frequency be set in accordance with the CPU
&Host/PCIe Clock Frequency (Note)
CPU Base Clock is set to Manual.
&Processor Base Clock (Gear Ratio) (Note)
Host/PCIe Clock Frequency by several
CPU Base Clock is set to Manual.
&Spread Spectrum Control (Note)
&Host Clock Value
This value is determined by multiplying the Host/PCIe Clock Frequency value by the Processor Base
Clock (Gear Ratio) value.
&Processor Graphics Clock
&CPU Upgrade (Note)
&CPU Clock Ratio
Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU
being installed.
&CPU Frequency
Displays the current operating CPU frequency.
`Advanced CPU Core Settings
&CPU Clock Ratio, CPU Frequency
The settings above are synchronous to those under the same items on the Advanced Frequency Settings
menu.
&K OC (Note)
Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall
and reduce the useful life of these components. This page is for advanced users only and we recommend you not to
- 20 -
Intel®CPUs' unique features, please visit Intel's website.
&CPU PLL Selection
Allows you to set the CPU PLL. Auto
&Filter PLL Level
Allows you to set the Filter PLL. Auto
&Uncore Ratio
Allows you to set the CPU Uncore ratio. The adjustable range is dependent on the CPU being used.
&Uncore Frequency
Displays the current CPU Uncore frequency.
&Intel(R) Turbo Boost Technology (Note)
Allows you to determine whether to enable the Intel CPU Turbo Boost technology. Auto lets the BIOS
&Turbo Ratio (1-Core Active~4-Core Active) (Note)
Allows you to set the CPU Turbo ratios for different number of active cores. Auto sets the CPU Turbo ratios
&Turbo Power Limit (Watts)
Allows you to set a power limit for CPU Turbo mode. When the CPU power consumption exceeds the
Auto
&Core Current Limit (Amps)
limit, the CPU will automatically reduce the core frequency in order to reduce the current. Auto sets the
&No. of CPU Cores Enabled (Note)
Allows you to select the number of CPU cores to enable in an Intel®
&Hyper-Threading Technology (Note)
Allows you to determine whether to enable multi-threading technology when using an Intel®CPU that
supports this function. This feature only works for operating systems that support multi-processor mode.
Auto
&CPU Enhanced Halt (C1E) (Note)
Enables or disables Intel®
halt state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to
decrease power consumption. Auto
&C3 State Support (Note)
Allows you to determine whether to let the CPU enter C3 mode in system halt state. When enabled, the
CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.
The C3 state is a more enhanced power-saving state than C1. Auto
&C6/C7 State Support (Note)
Allows you to determine whether to let the CPU enter C6/C7 mode in system halt state. When enabled, the
CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.
The C6/C7 state is a more enhanced power-saving state than C3. Auto
Other manuals for GA-Z97P-D3
1
Table of contents
Other Gigabyte Motherboard manuals
Gigabyte
Gigabyte GA-F2A68HM-DS2H User manual
Gigabyte
Gigabyte GA-H270-Gaming 3 User manual
Gigabyte
Gigabyte GA-G41MT-S2 User manual
Gigabyte
Gigabyte GA-EP35C-DS3R User manual
Gigabyte
Gigabyte A520I AC User manual
Gigabyte
Gigabyte GA-AB350M-D3V User manual
Gigabyte
Gigabyte MW22-SE0 User manual
Gigabyte
Gigabyte GA-PH67A-UD3-B3 User manual
Gigabyte
Gigabyte GA-K8NS Pro User manual
Gigabyte
Gigabyte GA-Z68A-D3H-B3 User manual
Gigabyte
Gigabyte GA-Z87X-UD7 TH User manual
Gigabyte
Gigabyte GA-P61-S3 User manual
Gigabyte
Gigabyte Z790 A ELITE AX DDR4 User manual
Gigabyte
Gigabyte X570 UD User manual
Gigabyte
Gigabyte GA-K8VT800-RH User manual
Gigabyte
Gigabyte GA-P31-ES3G User manual
Gigabyte
Gigabyte GA-8VD667 User manual
Gigabyte
Gigabyte N4120I H User manual
Gigabyte
Gigabyte GA-890FXA-UD5 User manual
Gigabyte
Gigabyte GA-M51GM-S2G User manual
