GigE Baumer HXG20 User manual

Safety
Further Information
For further information on our products visit www.baumer.com
For technical issues, please contact our technical support:
[e-mail]· Phone [phone] · Fax [phone]
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed matter not guaranteed.
Subject to change without notice. Printed in Germany v18 11/20. 11086858
FCC – Class A device
N: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursu-
ant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interfer-
ence in a residential environment. This equipment gener-
ates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occure in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
󰀨
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
Conformity:
CE, FCC Part 15 Class A, RoHS
Safety instructions
Notice
See User´s Guide for the com-
plete safety instructions!
Protect the sensor from dirt and
moisture.
Never open the camera housing.
Avoid camera contamination by
foreign objects.
Environmental requirements:
Storage temp. -10°C ... +70°C
Operating temp. +5°C ... +50°C
Housing temp. max. +50°C
Humidity 10 % ... 90 %
non-condensing
Quick Start Guide
HXG cameras with CMOS sensors (Release 2)
Product Specication
HXG cameras – Maximum Performance with CMOSIS sensors
Dual Gigabit Ethernet progressive scan CMOS camera
Binning, subsampling, true partial scan function (ROI) for increased frame rates
High Dynamic Range (HDR) image acquisition
External synchronization via industrial compliant process interface (trigger / flash)
Global shutter architecture for minimized motion blur
Power over Ethernet support
Standard RJ45 connectors
GigE VisionTM standard compliant
Excellent image quality
Camera parameter programmable in real-time
Frame rates up to 105 fps (HXG20 / Monochrome)
Camera Type Sensor
Size Resolution Full Frames [max. fps]
Burst Mode
(bu󰀨ered)
Monochrome
HXG20 2/3“ 2048 x 1088 105 337
HXG20NIR 2/3“ 2048 x 1088 105 337
HXG40 1“ 2048 x 2048 56 180
HXG40NIR 1“ 2048 x 2048 56 180
Color
HXG20 2/3“ 2048 x 1088 105 337
HXG40 1“ 2048 x 2048 56 180
Installation
open wire
Installation sample without PoE
1 - network interface card
2 - network cable
3 - Process interface cable
4 - Power cable
Dimensions

36 26 26
36
16 x M3 depth 6
UNC 1/4-20
52
52
26 36
55
5
12,5
10
Dimensions

52
52
26 36
UNC 1/4 - 20
26 36
16xM3 deph 5
26 36
54,7
open wire
4
open wire
5
4
Installation sample with PoE via NIC
1 - PoE network interface card (NIC)
2 - network cable (PoE)
3 - network cable (without PoE)
4 - Process interface cable
Installation sample with PoE via Injector
1 - network interface card (NIC)
2 - network cable (without PoE)
3 - Injector
4 - network cable (with PoE)
5 - Process interface cable
Download latest camera software:
www.baumer.com/vision/software
Download latest technical documentation:
www.baumer.com/cameras/docs

LED Signaling
1
2
3
LED Signal Meaning
1green

Link active
Receiving
2yellow Transmitting
3green
yellow
Power On
Readout active
General Description
123
4
56
No. Description No. Description
1(respective) lens mount 4Digial-IO
2Power Supply 5Data Port 2
3Data Port 1 6Signaling-LED
Heat Transmission
Caution
Provide adequate dissipation of heat, to ensure that the temperatu-
res does not exceed +50°C (+122°F).
The surface of the camera may be hot during operation and imme-
diately after use. Be careful when handling the camera and avoid
contact over a longer period.
T T
T: Housing temperature
measurement point
It is very important to provide adequate dis-
sipation of heat, to ensure that the housing
temperature does not reach or exceed +50°C
(+122°F). As there are numerous possibilities for
-

are suggested:
Operate the cameras only in mounted condition
with a good heat conductor (e.g. aluminum)
Mounting in combination with forced convection
may provide proper heat dissipation
Data Interfaces
Data / Control
1000 Base-T (Port 1)
Data / Control
1000 Base-T (Port 2)
wire colors of the connecting cable
LED2 LED1
81
LED2 LED1
81
1 green/white MX1+ 1 green/white MX1+
2 green MX1- 2 green MX1-
3 orange/white MX2+ 3 orangeg/white MX2+
4 blue MX3+ 4 blue MX3+
5 blue/white MX3- 5 blue/white MX3-
6 orange MX2- 6 orange MX2-
7 brown/white MX4+ 7 brown/white MX4+
8 brown MX4- 8 brown MX4-
Notice
Data port 1 supports Power over Ethernet (38 VDC .. 57 VDC).
For the data transfer, the ports are equal. For Single GigE connect one port and
for Dual GigE connect the second port additionally. The order does not matter.
Power Supply and Process Interface
Power Supply Digital I/O
M8 / 8 pins
wire colors of the connecting cable
1
4
3
8
5
7
3
1
42
6
1 brown Power VCC 1 white Line 5
3 blue GND 2 brown Line 1
4 black not used 3 green Line 0
4 yellow GND
5 grey Uex
6 pink Line 3
7 blue Line 4
8 red Line 2
Power Supply
Power VCC 20 VDC ... 30 VDC