GLD Products POCKEY 3 IN 1 GAME TABLE User manual

GLD Products
Pockey 3 in 1 Table
June 2018
POCKEY 3 IN 1 GAME TABLE
Assemblyvideos
available at
gldproducts.com
Vídeos para armar
disponible en
gldproducts.com

GLD Products
Pockey 3 in 1 Table
Parts Identifier
Part
No./
Qty
Illustration/
Order Number
Part
No./
Qty
Illustration/
Order Number
Part
No./
Qty
Illustration/
Order Number
1
Qty.
1
Table Top
Order No. 2-210
2
Qty.
2
Pedestal
Order No. 2-247
3
Qty.
2
Side Rail
Order No. 2-6
4
Qty.
2
End Rail
Order No. 2-8
5
Qty.
4
Raised Table Lock
Order No.2-209
6
Qty.
2
Puck Catcher
Order No. 2-202
7
Qty.
4
Goalie
Order No. 2-18
8
Qty.
18
1/4 Barrel Nut
Order No. 2-12
9
Qty.
4
Felt Pad
Order No. 2-19
10
Qty.
8
Hex Head Bolt 1/4" x 3"
Order No. 2-14
11
Qty.
10
Hex Head Bolt 1/4" x 2"
Order No. 2-13
12
Qty.
18
1/4" Washer
Order No. 2-15
13
Qty.
16
1/2" Phillips Head Screw
Order No.2-31
14
Qty.
6
3/4" Washer
3 are pre-assembled
Order No. 2-16
15
Qty.
4
3/4" Hex Nut
2 arepre-assembled
Order No. 2-17
16
Qty.
4
Hockey Puck
Order No. 2-20
17
Qty.
1 Set
Billiard Balls
Order No. 2-21
18
Qty.
1
Brush
Order No. 2-22
19
Qty.
2
Cue Stick
Order No. 2-23
20
Qty.
2
Chalk
Order No. 2-24
21
Qty.
1
Open End Wrench
Order No. 2-25
22
Qty.
4
Leg Leveler
Order No.2-26
23
Qty.
1
Triangle
Order No. 2-27
24
Qty.
1
Box Wrench
Order No. 1-17

GLD Products Pockey 3 in 1 Table
Parts Identifier
25
2 Cues Rack
Order No. 2-204
26
Qty.
2 Accessory Holder
Order No. 2-205
27
Qty.
1 Table Tennis Net With Posts
Order No. 8-10
28
Qty.
2 Table Tennis Top (End)
Order No. 2-286
29
Qty. 3/16" x 1" Allen Key Bolt
8 Order No. 2-203
30
Qty. Allen Wrench
1 Order No. 2-116
31
Qty. Slide Scorer
2 Order No. 2-208
32
Qty. F4 x 1" Phillips
4 Countersunk Screw
Order No. 2-134
33
Qty. W/P4 x 1-14" Screw
18 Pre-assembled
Order No. 2-206
34
Qty.
4 Wraparound Black Corner
Pre-assembled
Order No. 2-215
35
Qty.
2 Table Tennis Ball
Order No. 8-4
36
Qty.
2 Table Tennis Bat
Order No. 8-5
37
Qty. Table Tennis Top (Middle)
1 Order No. 2-287

GLD Products
Pockey 3 in 1 Table
Preparing for Assembly
• Be sure to unpack all of the parts included in this package.Check
inside any tubes or sleeves. Save all packing material until the
product is fully assembled and functional.
• Compare the parts in your package with the PartsIdentifier
description on page 4. and 5
• After unpacking large products, some disassembly may be required
prior to beginning the assembly.

GLD Products
Pockey 3 in 1 Table
Tools Required
• Allen Wrench (#30)
• Open End Wrench (#21)
• Box Wrench (#24)
• Phillips Screwdriver (not included)
• Flat Blade Screwdriver (not included)
• Level (not included)
• Electric screwdriver may be helpful. CAUTION: You must set at
LOW TORQUE and use extreme caution because you could
overtighten the hardware, strip the screws, or damage the table.
Assembly Tips
Make sure you understand the following before you begin to assemble your game table.
1. READ THIS MANUAL all the way through before beginning assembly.
2. When installing parts that have more than one bolt, start ALL bolts in that part byhand
before tightening anything.
3. Some drawings or images in this manual may not look exactly like your product.
4. You may need a second adult to assist with this assembly.
Note: Save all packing materials until the parts have been inspected and the table is
assembled.
Unpack the Pieces
• Lay the box on a flat surface (floor). You may want this nearyour
area of assembly.
• Unpack the boxes and part bags. Inspect and count the parts.The
Parts Identifier page can be used to record your results.
• If any parts are damaged or missing, contact GLD Customer
Service.
• Missing fasteners may be purchased at a hardware store usingthe
descriptions on the Parts Identifier page.
Games
This game table includes the equipment and game pieces for the following games:
Air Hockey Pool Table Tennis
The rules for these games are not discussed in this manual.

GLD Products
Pockey 3 in 1 Table
1
33
STEP 1 - ASSEMBLE THE PEDESTAL
Remove all components from the carton.
NOTE: Parts are packed inside the table top (#1). Remove the pool table surface from the
table top (#1) by removing all the screws (#33) that hold it in place. Inside the table
top you will find all the parts needed to assemble your table. when all the parts are
out of the table top, replace the pool table surface. Reattach the pool table surface
by replacing the screws (#33). The assembly parts will include a total of 18 screws
(#33). This includes the screws you removed when separating the pool table sur-
face from the table top (#1). Be sure to use all 18 screws (#33) when you reattach
the pool table surface to the table top (#1)
1. Carefully remove the two (#2) pedestals and four levelers (#22) from thepackage.
2. Insert levelers into pre-drilled holes in the bottom of each leg of the pedestal and secure
part way.

GLD Products
Pockey 3 in 1 Table
#22
#22
#2

GLD Products
Pockey 3 in 1 Table
STEP 2 - ATTACH THE TABLE LOCKS
IMPORTANT: The T-nuts are pressed in at the factory. They are on the side of the pedestal
that faces the table top (the inside).
1. Attach two table locks (#5) to the outside of each pedestal using bolt (#29).
#5
#29 Table top goes
on this side
STEP 3 - ASSEMBLE THE BASE
1. With the help of another person, attach the end rails (#4) to the side rails (#3) using 2"
hex bolts (#11), washers (#12), and barrel nuts (#8). Hand tighten bolts.
#11
Table top on
this side
T-nuts
#11
#12
#12
#11
#12
#12
#11

GLD Products
Pockey 3 in 1 Table
#12
#12
STEP 4 - SECURE THE BASE TO THE PEDESTALS
1. Insert barrel nuts (#8) into the seven holes in the base.
2. Start the four 3" hex head bolts (#10) with 1/4" washers (#12) through the ends ofthe
pedestal and into the side rails. Finger tighten.
3. Start the three 2" hex head bolts (#11) with 1/4" washers (#12) through the center of the
pedestal and into the end rails. Finger tighten.
4. Tighten all bolts using the box wrench (#24).

GLD Products
Pockey 3 in 1 Table
STEP 5 - ATTACH THE TABLE TOP
NOTE: The end of the table top with the power cord has the three 3/4" washers (#14) and
two 3/4" hex nuts (#15) pre-assembled on the power cord.
It is possible that the support axle bolts are not pushed out completely. To pull them
out, thread a nut onto the end and pull outward with pliers. If the bolt does not pull
out freely, tap it with a hammer to break it loose, then pull.
1. Open all four of the table locks.
WARNING: Dropping the table or resting all ofthe table weight on one or two of closed table
locks is likely to break the lock mechanism.
2. Place one 3/4" washer (#14) over the support axle. Thread the 3/4" hex nut (#15)onto
the axle followed by another washer (#14).
3. Lift the table top into position over the side supports.
4. Lower the table top so the supporting axles drop into the slots in the pedestals.
NOTE: The two washers and the nut should be placed to the inside of the pedestals.
5. Place another washer (#14) and thread a nut (#15) onto the support axle.
6. Release all of the table locks. Tighten the nuts on the support axle to providesmooth
table top rotation.
Open the
Table Locks
#15
#14
#14
#14
#15

GLD Products
Pockey 3 in 1 Table
#28
#37
#28
STEP 6 - ATTACH PUCK CATCHERS AND ACCESSORY HOLDER
1. Align the puck catcher (#6) with the pre-drilled holes on each end of the playing table.
Secure it to the pedestal with round head screws (#13). Run the power cord throughthe
puck catcher.
2. Align the accessory holder (#26) with the pre-drilled holes on each end of theplaying
table. Secure it to the pedestal with screws (#13).
3. Attach both slide scorers (#31) to the edges of the playing table using four screws(#32).
4. The table tennis top is made up of three pieces; two ends (#28) and one middle(#37).
Push the three pieces together and use the attached velcro strips to secure them.
5. The net (#27) is attached to the middle section (#37).
#27
#32 #31
#32 #32 #31
#32
#6
#13
#25
#13
#26

GLD Products
Pockey 3 in 1 Table
STEP 7 - ADJUST LEVELERS
1. With the help of another person, turn each leg leveler until the table rests level to floor.
2. Check with a carpenters level placed cross-wise and length-wise on the tabletop.
3. Readjust levelers if necessary.
STEP 8 - ASSEMBLE GOALIES
Remove backing from felt pads (#9) and place on bottom of goalies (#7).
#9
The assembly is complete.
To Rotate the Table:
CAUTION: This should be performed by an adult. The rotating table may pinch body parts.
• Pull out two table locks on one end.
• On the other end, pull out the two table locks.
WARNING: You must open all four of the table locks. Do not rotate the table with any of the
table locks closed. The momentum of the rotating table may break the lock.
• Slowly rotate the table.
• Push in the table locks.
#9
#7

GLD Products
Pockey 3 in 1 Table
To Level the Table:
• Place a carpenters level on the table.
• Screw the leg levelers in or out until table is level.
Troubleshooting:
• If the pool table side is not level, first try to level it by using the leg
levelers on each leg. Most of the time the table can be easily leveled
using this method.
If the fan does not go on:
• Unplug the fan from electrical outlet.
• Inspect wiring for proper connection.
• Plug in to test.
If the fan works but the table has dead spots:
• Use a small drill bit and clear the holes by hand. DO NOTuse
electric drill. Manually push the drill bit into the holes toclear.
Clean the surface by spraying a rag (do not spray directly onto the table top) with a furniture
polish (like Pledge) and buffing the surface of the table and the puck. This will provide a bit
more “float” which may help prevent getting hung up in the “dead” areas.

GLD Products
Pockey 3 in 1 Table
Care and Use of your Table
• This product is intended for INDOOR use only.
• DO NOT sit, climb, or lean on the table.
• DO NOT drag the table when moving it. This will damage the legs.
• Keep your table covered.
• To clean the hard surfaces spray a cloth with a mild cleanerand
wipe.
• Pucks that fly off the table may have chipped edges. Inspect the
puck and replace if needed.