Global leak detection Gld-40 User manual

OPERATOR’S MANUAL

Diagnostic Smoke® Vapor Machine

with UltraTraceUV® Dye Solution

Leak Detection System

Model No. GLD-40

USA | Canada Patents ●6,392,227 • 6,526,808 | 2,279,147 | Int’l Patents Pending

Caution

Usage Tips

TO PREVENT PERSONAL INJURY

AND / OR DAMAGE TO VEHICLE OR EQUIPMENT

ALWAYS use on vehicle with engine turned <OFF>.

Use this equipment in the manner specified by the manufacturer.

Understand operating procedures / Follow all safety precautions.

Connect Tester to chassis ground.

Use UltraTraceUV®Smoke Solution No. GLD0712UV in this Tester. Using a non-approved

solution may cause damage to vehicles being tested and may cause personal injury.

Never leave the Tester’s hoses or power cables connected to the vehicle for extended periods

of time when tests are not being performed.

Do not perform test near source of spark or ignition.

Wear eye protection that meets OSHA standards.

Follow safety precautions when using ultraviolet light source.

Always use hood support if hanging Tester from hood of car.

Air pressure (or gas pressure) supplied to Tester can be between 50-175 PSI (3.4 to 12 bar).

Connect to workshop airline for general purpose leak detection applications.

Smoke exiting a very small leak is sometimes even easier to see if after filling the system with smoke you reduce

the smoke flow by turning the flow control knob clockwise, which slows the exiting smoke velocity and helps you

see very small leak(s)

Use the white light provided to highlight the smoke exiting a leak.

Use the Ultraviolet (UV) light and yellow glasses provided to look for the fluorescent deposit at the exact location

of a leak. When using alternate source of UV light, be sure it is one that covers the 400 nanometer (nm) UV light

range.

When operating the Tester in near freezing temperatures, cycle the operation of the Tester 15 seconds ON and 15

seconds OFF for approximately the first minute or two of operation. This will allow the Tester to reach its

optimum operating temperature.

When testing an engine's intake or exhaust system for leaks, it is recommended that the engine be cold. Small

leaks may be sealed due to thermal expansion.

Table of Contents

Included with the Smoke Wizard

Prior to using Smoke Wizard®for the First Time

Specifications

Smoke Wizard®Overview

Basic Testing Procedure

Leak Detection Applications

Troubleshooting

Warranty

Material Safety Data Sheet (MSDS)

CE Certificate

Page 1

Page 2

Page 3

Page 3 & 4

Page 5

Page 6 – 8

Page 9

Page 10

Page 11 – 14

Page 15

Be sure to visit our website http://www.smokewizard.co.uk for:

●Instructional Videos ●Additional Product Details

●Frequently Asked Questions ●Tech Tips ●Downloads

Congratulations! You have purchased the finest and most feature-rich portable leak

detection smoke machine available today. The patented technology inside your Smoke

Wizard was designed in collaboration with major automakers; was designed specifically to be

safe for leak testing a vehicle’s fuel evaporative (EVAP) system as well as many other vehicle

systems; is the only technology in the world approved by any automaker; and is the only

smoke technology that meets SAE INTERNATIONAL published papers recommendation to use

a smoke machine designed to function with an inert gas (such as Nitrogen, Argon or CO2)

when testing a vehicle’s EVAP system [SAE: 2007-01-1235 & 2008-01-0554].

Global Leak Detection Corp. and our Authorized Distributors, Smoke Wizard UK, thank you

for the purchase of your new Smoke Wizard!

Diagnostic Smoke®Vapor – Safe for Vehicle Systems.

Included with the Smoke Wizard®

UltraTraceUV®;(GLD0712UV) this patented solution is the only Automaker-

approved smoke-producing solution in the world. The solution’s chemistry contains

a special dye that deposits at the exact location of a leak. Will not harm automotive

systems and will perform approximately 300 tests. (12 oz. / 355 ml). (Part number is

for one 12 oz. bottle. Two bottles included with machine)

Combination Light: (GLD043K) delivers a white light for easier smoke location, an

ultraviolet (UV) light that highlights the fluorescent dye deposited at the exact

location of a leak and red laser pointer light. Includes 3 AAA batteries and glasses.

EVAP Service Port Adaptor – standard size: (GLD003)

Dual-Size Schrader Valve Removal/Installation Tool: (GLD004) The Schrader valve

has a left-hand thread. Turn clockwise to remove!

Cap Plugs Kit: (GLD005) these cap plugs are useful when sealing an intake manifold

system in order to contain the smoke in the system for proper leak testing, such as

mass airflow sensor ducting, etc

Smoke Diffuser: (GLD006) this adapter is designed to locate leaks around doors,

windows, sunroofs and trunk compartment. The adapter allows the operator to lay

down a thick bed of smoke (from outside the vehicle) along door and window seams

in order to watch for disturbance caused by escaping airflow due to a leaking seal.

Internal pressure is created by vehicle’s HVAC set to fresh air (i.e. not recirculation)

and blower fan on high speed.

Adapter Cone: (GLD007) for introducing smoke into the exhaust system or into any

orifice that accommodates the cone's size, such as the induction system

Adapter: (9995545). NOTE: This adapter, while part

of the overall kit, is not included with the Smoke

Wizard®, but instead arrives separately from SPX.

Use this adapter to introduce smoke into the

engine intake system, as illustrated.

Prior to Using Smoke Wizard®for the First Time

NOTE: Your Smoke Wizard arrives with: a commonly used male quick-disconnect Air Fitting

and two bottles (12 oz/355 ml) of UltraTraceUV® Smoke Producing Solution.

1. Be sure the Smoke Wizard’s Air Fitting is the correct fitting

for your air hose connector or change it to match. (Figure 1)

2.Remove the Smoke Wizard’s dipstick; pour the entire contents of one bottle into the smoke

chamber; verify correct level and secure dipstick. (Figure 1)

NOTE: Use the second bottle supplied to maintain solution level at or near FULL mark.

NOTE: Your Smoke Wizard is now ready for operation.

NOTE: A common question asked is if one can use a basic generic mineral oil, such as ‘Baby Oil’, in the

Tester to create the smoke.

You can if you want to, but we don’t recommend it. The patented UltraTraceUV® smoke solution

supplied with this Tester; will perform hundreds of tests that only cost pennies per test; is the only

solution in the world approved by the auto manufacturers; and will not void any vehicle factory

warranties. Plus you have the added benefit of the trace dye that marks the exact location of a leak,

increasing diagnostic accuracy unlike any other. This special solution is not a “generic” mineral oil. In

fact, generic mineral oils are not intended for this type industrial use. The generic mineral oils break

down, evidenced by its foul odor and could damage vehicle components.

Caution: Factory vehicle bonnet supports are not designed

to support more than the weight of the bonnet. A

supplemental prop rod (or similar device) such as the one

shown here should always be used when hanging the

smoke machine from the bonnet, in order to avoid hazard

and possible injury due to a hood falling unexpectedly.

Figure 1

Air Fitting

Smoke solution port

Smoke Wizard®Overview

Technical Specifications

Height (less hanger)

Length

Width

Weight

Shipping weight

Power supply

Power consumption

13 in. (33 cm)

5.5 in. (14 cm)

9.5 in. (24 cm)

10 lb. (4.5 kg)

14 lb. (6.3 kg)

12 volts DC

15 amps.

Supply pressure

Supply volume

Smoke supply line

Power supply line

Operating temp. range

Solution Max. Volume

13.0 in. H2O (0.032 bar)

10 liters per minute

10 feet (3m)

45°F to 140°F (7.2°C to 60°C)

12 oz. (355 ml)

12V DC Power-Supply Cables

(Rear of Tester)

Suspension Hanger – allows the

option of hanging your Smoke

Wizard from a convenient test

location on the vehicle or for

storage when not in use.

Note: Always use bonnet support

device when hanging from the

bonnet.

Filter Drain Port – located under Tester;

keeps Tester and vehicle clean by

automatically draining water and

contaminants from shop air compressor.

Control Panel

–

See next page

Smoke Solutio

n Dipstick

–

use to

check and maintain proper smoke

solution level.

Smoke Supply hose

–

hose with

scratch-resistant Delrin® nozzle

delivers the smoke vapor into a

system for leak testing.

Air Fitting

–

connect to shop a

inert gas. Note: There is a pressure

regulator inside the Tester so no

external regulator is required as long

as input pressure is between 50 and

175 PSI (3.4 to 12 bar).

Control Panel Overview

Flow Meter: If the meter indicates flow, then you know there

is flow going into (or through) the system being tested. If

flow meter indicates flow after the system is filled, this

indicates a leak. The higher the ball is in the flow meter, the

larger the leak size.

No flow indicates no leak.

Observing the flow meter behavior allows Technicians to

judge system blockage, restrictions, control effectiveness, and

system operational integrity.

Flow Control Valve: Easy to read ¼ turn valve allows

total control of the volume of Diagnostic Smoke® vapor

exiting the leak. First, fill system with smoke at full

flow. Then reduce the smoke volume by adjusting the

Flow Control Valve so that the leak is even easier to

see.

Sometimes less smoke exiting a small leak is easier

to see.

Flow Control Valve does not affect delivery pressure;

it only affects the volume of flow.

SMOKE Light

(Red):

Turns ON

when you press the START

button, indicating smoke

production.

POWER Light (Green):

Turns

ON when you connect Tester

to 12-

Volt DC power.

Blinks if the battery power

source is insufficient.

START Button:

Press for smoke production.

Note: Is on 5-minute timer.

Pressure Gauge:

(-30 to +30 IWC) used to verify

leak(s) in a system, using either

pressure-decay or vacuum-decay.

The pressure / vacuum decay

test cannot tell the size of the

leak(s). Leak size can be

determined using the indexed

flow meter.

Indexed on Flow Meter:

indicates

three critical EVAP leak thresholds

of .010" .020" and .040" for

diagnostic accuracy.

.040" (1 mm)

.020" (½ mm)

.010" (¼ mm)

Note: Flow Control Valve must be

in full flow position for proper

measurement.

Basic Testing Procedure

1. Connect Tester to shop air. See Optional Gas Source below.

2. Connect Tester’s Red power cable to vehicle’s 12 Volt DC battery

positive terminal.

>Battery must be in good condition and fully charged!

3. Connect Tester’s Black cable to vehicle’s chassis ground. Do NOT

connect the black cable to battery ground because a spark in the vicinity

of the battery can cause an explosion! (Figure 2)

4. Observe that the Green Power indicator lamp on the Tester is ‘ON’

confirming that you are properly connected.

>A blinking green power lamp indicates insufficient battery power to the

Tester.

5. Connect smoke supply hose to system being tested.

6. Flow Control Valve must be in Full Open position. (Figure 3)

7. Press START button and fill system with smoke.

>Whenever possible it is best to ‘purge’ the ‘non-smoke’ air out of the system

being tested in order to quickly fill the system with smoke.

>Smoke production is on 5-minute timer.

8. Use white light supplied and look for exiting smoke or use ultraviolet light

supplied to look for fluorescent dye deposit at exact location of a leak.

>The longer smoke is allowed to exit a leak, the more fluorescent dye will be

deposited at leak locations.

Figure 2

Black to

chassis

ground

Figure

Flow

Control

Do NOT run the vehicle engine with the Smoke Wizard® supply

hose connected to the vehicle. Normal engine vacuum will

damage the pressure/vacuum gauge!

Sample Leak Detection Applications:

This leak Tester can be used in virtually any vehicle low pressure system suspected of having a leak, such

as; intake / induction system, intercooler and turbocharger system, vacuum system, exhaust system,

wind/water leaks and can also be used to verify air solenoid functions and test components prior to

assembly.

1. Introduce smoke into system.

2. Look for smoke (or dye) exiting leak(s).

Intake / Induction Leaks

Exhaust Leaks

Wind and Water Leaks

e’

’s

o‘

‘F

r’

’a

r’

’s

Smoke distrubance pinpoints the leak

No air distrurbance means ‘No Leak’

Sample Fluorescent Dye Deposits

The patented smoke vapor contains a special ultraviolet-activated fluorescent dye that gets deposited at

the exact location of a leak. Use the UV light provided to highlight the dye.

>This technology is designed so that the dye will only deposit if there is pressure-differential. So for

instance, the dye will deposit when exiting a leak but will not deposit during the wind and water test.

>The longer the smoke is allowed to exit a leak, the more dye will be deposited.

Troubleshooting Guide

Your Smoke Wizard has two indicator lights on the control panel that double as diagnostic lights,

indicating if the Tester is working correctly. The following table describes the indicator light function

codes.

Green Red Interval Cause

Constant ON Sufficient battery power

Blinks: 1 per second Insufficient battery power

  Blink simultaneously: 1 per second Bad ground or power connection at smoke

canister or short in circuit

  Blink simultaneously: 4 times per second Bad ground at smoke canister or open

heating circuit

 

Blink alternately: 1 per second

(System will shut down; Power must be

disconnected then reconnected)

Bad ground. Can also mean circuit board

failure ٭

Symptom Likely Cause Solution

The green power

indicator lamp on the

Tester does not turn

ON.

1. The power cables are reversed.

2. Poor power-supply cable

connection.

3. Battery providing power is too

weak.

1. Correctly position the power cables.

2. Secure the connection at the positive

terminal and chassis ground.

3. Verify the battery is in good condition

and fully charged.

I turn the Tester ON but

there is no air or smoke

coming out of the

supply hose.

1. Flow Control valve is closed.

2. Poor power-supply cable

connection.

3. Battery providing power is too

weak.

4. Air supply to tester is

insufficient.

5. Smoke-vapor could be

condensing inside the smoke

supply hose, restricting smoke

flow.

1. Open flow control.

2. Secure the connection at the positive

terminal and chassis ground.

3. Verify the battery is in good condition

and fully charged.

4. Be sure air supply is sufficient.

5. Be sure the smoke hose is fully

extended when in use. Drain the

condensation from the hose prior to its

next use, either by placing the machine

higher than the hose, or by removing the

hose and blowing through it with

compressed air. Do NOT blow

compressed air into the machine with the

smoke hose connected to the machine.

٭If circuit board failure occurs, first try disconnecting power to your Smoke Wizard for 10 seconds and

reconnect. If this failure code occurs a second time, disconnect Smoke Wizard and contact Smoke Wizard UK

at: SmokeWizardSupport@virginmedia.com.

Warranty

Warranty Issues or Questions? Contact Smoke Wizard UK

SmokeWizardSupport@virginmedia.com

www.SmokeWizard.co.uk

Activate Your Warranty

To activate your Smoke Wizard®warranty; send the information below to the email address provided

within 30 days of your purchase.

Send information to: [email protected]

Purchaser’s Name:

Company Name:

Address:

Country:

Telephone number:

Email address:

Web address:

Enter Smoke Machine Model as: GLD-40 (J/LR)

Serial Number:

Date Purchased (keep your invoice for verification, if needed):

LIMITED ONE (1) YEAR WARRANTY

Global Leak Detection warrants the Smoke Wizard to the Original Purchaser that under normal use,

care and service, the Equipment (except as otherwise provided herein) shall be free from defects in

material and workmanship for ONE YEAR from the date of original invoice.

Seller's obligations under this warranty are limited solely to the repair or, at Seller's option, replacement of or

refund of the original purchase price for, Equipment or parts which to Seller's satisfaction are determined to be

defective and which are necessary, in Seller's judgment, to return the equipment to good operating condition.

Repairs or replacements qualifying under this Warranty will be performed or made on regular business days

during Seller's normal working hours within a reasonable time following Buyer's request. All requests for

warranty service must be made during the stated warranty period.

Rev. 27June2011

MATERIAL SAFETY DATA SHEET Page 1 of 4

COUNTRY

U.S.A.

% (by

Weight) Hazard

Symbol

Notes:

SKIN:

EYES:

NTP?

CALIFORNIA, Prop.65? OSHA REGULATED?

PRODUCT NAME:

UltraTraceUV®

(Fluorescent Diagnostic Smoke® Solution)

PRODUCT PART NUMBERS: GLD0712UV | GLD0708UV

GENERAL USE:

TRADE NAME:

DATE PREPARED:

SUPERSEDES:

Global Leak Detection Corp.

NO NO NO

This is basically a safe product. However, human health risks vary from person to person. As with any petroleum base product, reasonable caution

should be taken to avoid prolonged and repeated exposure to the base product.

CAS #

Non-Hazardous

Hazardous Components

THIS PRODUCT HAS A LOW ORDER OF ACUTE ORAL TOXICITY. If base product is swallowed it presents a low risk of aspiration into the

lungs. In the event that swallowing the base product in small quantities does take place, it is expected to pass through the system without

symptoms. As with anypetroleum base product : If large quantities are swallowed and subsequently aspirated into the lungs, mild to severe

pulmonary injury may occur.

EMERGENCY OVERVIEW

INHALATION:

INGESTION:

The balance of the ingredients are proprietrary and non-hazardous as defined in US 29CFR 1210 and European regulation directive

67/548 EEC.

SECTION 3 - HAZARDS IDENTIFICATION

POTENTIAL HEALTH EFFECTS

UltraTraceUV®

Colorless to Very Pale Amber. Mineral Oil Type Odor.

DATE: June 25, 2011

Proprietary Pharmaceutical USP Petroleum Blend with APD Dye

TELEPHONE NUMBER FOR INFORMATION / Customer Service

1-714-433-2841

Proprietary

Huntington Beach, CA 92647 International

SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION

CHEMICAL FAMILY:

PRODUCT DESCRIPTION:

Leak Detection Smoke Machines

17852 Gothard Street

ADDRESS (NUMBER, STREET, P.O. BOX)

June 25, 2011

February 4, 2009

MANUFACTURER

01-813-248-05851-800-255-3924

CHEMTEL 24-HOUR EMERGENCY TELEPHONE NUMBER(CITY, STATE AND ZIP CODE)

CARCINOGENICITY: IARC MONOGRAPHS?

North America Toll Free

NO ESIS (EU)? NO

SECTION 2 - HAZARDOUS INGREDIENTS

Overexposure to skin may cause mild irritation.

Not a common route of exposure at room temperature, exposure to heated vapors from this product may cause irritation and coughing.

Overexposure to eyes may cause mild irritiation.

RISK PHRASES

(Full Text Section 15)EINECS #

MATERIAL SAFETY DATA SHEET Page 2 of 4

PRODUCT NAME:

UltraTraceUV®

(Fluorescent Diagnostic Smoke® Solution)

PRODUCT PART NUMBERS: GLD0712UV | GLD0708UV DATE: June 25, 2011

EYES:

SKIN:

TWA ppm TWA mg/m3 STEL ppm STEL mg/m3 TLV/TWA ppm TWA mg/m3 STEL ppm STEL mg/m3

NE NE NE NE NE NE NE NE

Water Spray (Fog), Foam, Dry Chemical and Carbon Dioxide.

INHALATION:

INGESTION:

Flush eyes with clean water for 15 minutes or until irritation subsides. If irritation persists, consult a physician.

NIOSH

Do not handleor store near heat, flames or strong oxidants.

PERSONAL PROTECTION

SECTION 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION

Inhalation at ambient temperatures is not commonly a problem. If overcome by excessive exposure to vapors,

you should remove from exposure to well ventilated area. Some people may experience dizziness, drowsiness or nausea.

If symptoms persist, consult a physician. It is always a good measure of precaution to avoid excessive inhalation of byproduct.

RESPIRATORY PROTECTION:

EYE PROTECTION:

PROTECTIVE GLOVES:

Combustible liquid Flash Point: 335-510°F (168-265°C). Distillation Range: 550-900° F (288-482° C). LEL:0.9% UEL: 7.0%

EXTINGUISHING MEDIA:

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE:

OTHER PROTECTIVE CLOTHING OR EQUIPMENT:

HAZARDOUS COMBUSTION PRODUCTS:

Carbon Monoxide, Soot, Smoke, Carbon Dioxide.

Non-Hazardous

SECTION 4 - FIRST AID MEASURES

SECTION 5 - FIRE FIGHTING MEASURES

Do not induce vomiting as a risk of aspiration exists with this petroleum based product. If ingested, the precaution is to call a physician and our

emergency number immediately.

Remove anycontaminated clothing and wash affected skin area with soap and warm water.

SECTION 7 - HANDLING AND STORAGE

SECTION 6 - ACCIDENTAL RELEASE MEASURES

UNUSUAL FIRE AND EXPLOSION HAZARDS:

ACGIH OSHA

HAZARDOUS COMPONENTS

GENERAL HAZARDS:

FIRE FIGHTING PROCEDURES:

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:

Do not store or mixbase chemical with strong oxidants. Do not cut, drill, grind, or weld container, as this may cause explosion.

Cool exposed container with water. Use air-supplied (SCBA) breathing equipment for enclosed or confined spaces.

Recover liquid, wash remainder with suitable petroleum solvent or add absorbent. As with all petroleum products, keep out of sewers and water

courses. Advise authorities if ever any petroleum product has entered or may enter sewers or water courses

Use this product in a well ventilated area.

Wash with soap and water after using this product and before eating drinking or smoking.

Eyewash station recommended.

Safety Glasses required.

Not required.

WORK / HYGIENIC PRACTICES:

MATERIAL SAFETY DATA SHEET Page 3 of 4

PRODUCT NAME:

UltraTraceUV®

(Fluorescent Diagnostic Smoke® Solution)

PRODUCT PART NUMBERS: GLD0712UV | GLD0708UV DATE: June 25, 2011

LEL: 0.90% UEL: 7.00%

STABILITY STABLE X

REFERENCE:

LABEL:

Note: Transportation information provided is for reference only. Client is urged to consult CFR 49 parts 100 - 177, IMDG, IATA, EU, United Nations

TDG, and WHMIS (Canada) TDG information manuals for detailed regulations and exceptions covering specific container sizes, packaging

materials and methods of shipping.

NAHAZARD SYMBOLS: Hazard Identification Number (HIN):

0.87-0.89

<1.0 mm Hg @68°F

INCOMPATIBILITY (MATERIALS TO AVOID):

WASTE DISPOSAL METHOD:

PROPER SHIPPING NAME:

SOLUBILITY IN WATERBOILING RANGE/ DISTILLATION RANGE

SPECIFIC GRAVITY (WATER = 1)

APPEARANCE AND ODOR

SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES

Colorless to Very Pale Amber. Mineral Oil Type Odor.

DOT HAZARD CLASS / Pack Group:

Not regulated

49CFR IMDG HAZARD CLASS:

RID/ADR Dangerous Goods Code:

UN TDG Class / Pack Group: NA

UN / NA IDENTIFICATION NUMBER:

SECTION 14 - TRANSPORT INFORMATION

Not regulated Not regulatedIATA HAZARD CLASS / Pack Group:

SECTION 12 - ECOLOGICAL INFORMATION

No ecological information is available for this blended product, however discharge to watercourses as with all petroleum based products should be

avoided.

SECTION 13 - DISPOSAL CONSIDERATIONS

Avoid discharge to watercourses, dispose preferably by incineration at a properly permitted facilityin accordance with all Local, Regional, State and

Federal regulations.

None related to polymerization.

SECTION 11 - TOXICOLOGICAL INFORMATION

Hazardous Components CAS #

EINECS # LD50 of Ingredient

(Specify Species and Route) LC50 of Ingredient

(Specify Species)

Not Hazardous/No Tox data

available.

HAZARDOUS POLYMERIZATION:

HAZARDOUS DECOMPOSITION OR BYPRODUCTS:

Will not occur

Carbon Monoxide, Soot, Smoke, Carbon Dioxide.

EVAPORATION RATE (WATER = 1)

VAPOR DENSITY (AIR = 1)

CONDITIONS TO AVOID:

Strong oxidizers

Excessive heat , sparks open flame, contact with oxidizers.

SECTION 10 - STABILITY AND REACTIVITY

FLAMMABLE LIMITS

FLASH POINT

AUTOIGNITION TEMPERATURE <0.01

335-510°F (168-265°C)

550-900° F ( 288-482°C)

Negligible

VISCOSITY

VAPOR PRESSURE

MATERIAL SAFETY DATA SHEET Page 4 of 4

PRODUCT NAME:

UltraTraceUV®

(Fluorescent Diagnostic Smoke® Solution)

PRODUCT PART NUMBERS: GLD0712UV | GLD0708UV DATE: June 25, 2011

NO NO

Fire: NO NO

Reactive: NO

313 REPORTABLE INGREDIENTS:

HEALTH: 0 = INSIGNIFICANT

1 = SLIGHT

2 = MODERATE

3 = HIGH

4 = EXTREME

REVISION SUMMARY:

Chronic Health:

RISK PHRASES: None required

Legend:

PHYSICAL HAZARD:

FLAMMABILITY:

Ingredients listed on CDSLDSL / NDSL (Canadian Domestic Substances List / Non-Domestic Substances List):

Sudden Release of Pressure:

Acute Health:

EINECS (European Inventory of Existing Commercial Chemical Substances):

IDL (Canadian Ingredient Disclosure List):

CPR (Canadian Controlled Products Regulations):

California Prop 65, Safe Drinking Water and Toxic Enforcement Act of 1986:

CERCLA (USA - Comprehensive Response Compensation and Liability Act):

Ingredients Referenced

SARA TITLE III (USA - Superfund Amendments and Reauthorization Act):

TSCA (USA - Toxic Substance Control Act):

Revised toGHS/EU protocols 02/04/2009 supersedes Rev12/2008 issue. ---JTV---

SYMBOL(S) REQUIRED FOR EU LABEL

PERSONAL PROTECTIVE EQUIPMENT:

The information contained herein is believed to be accurate but is not warranted to be so. ChemTel Inc. assumes no responsibility for document alterations or additions

after authorship and initial review excepting changes performed by ChemTel personnel. Data and calculations are based on information furnished by the manufacturer of the

product and manufacturers of the components of the product. Users are advised to confirm in advance of need that information is current, applicable and suited to

the circumstances of use. Vendor assumes no responsibility for injury to vendee or third persons proximately caused by the material if reasonable safety procedures

are not adhered to as stipulated in the data sheet. Furthermore, vendor assumes no responsibility for injury caused by abnormal use of this material even if reasonable

safety procedures are followed. All questions regarding this product should be directed to the manufacturer of the product as described in Section 1.

SAFETY PHRASES:

None listed

SECTION 16 - OTHER INFORMATION

None Listed

MSDS Prepared by:

ChemTel Inc.

1305 North Florida Avenue

Tampa, Florida USA 33602-2902

Toll Free North America 1-888-255-3924 Intl. +01 813-248-0573

Website: www.chemtelinc.com

HMIS HAZARD RATINGS

None required.

NA = Not Applicable NE = Not Established NR = Not Reported (proprietary).

WGK Water Quality Index:

None listed None listed None listed

No RQ's listed.

None reportable.

SECTION 15 - REGULATORY INFORMATION

Listed

25791 Commercentre Drive

Lake Forest, CA 92630

Telephone: 949-448-4100

Facsimile: 949-448-4111

This report is for the exclusive use of Intertek’s Client and is provided pursuant to the agreement between Intertek and its Client. Intertek’s responsibility and liability are

limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss,

expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of

the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations

and test results in this report are relevant only the sample tested. This report by itself does not imply that the material, product or service is or has ever been under an

Intertek certification program.

Intertek Testing Services NA, Inc

EMC VERIFICATION No. 3179331LAX-001g

EQUIPMENT

Type of equipment Evaporate Emissions System Tester

Model GLD-40

Company Global Leak Detection Corp.

Test Report No. 3059793.011 (Intertek – Minnesota)

Test Standard

Emissions

EN 61326:1997, Class B

Immunity