GO4 Vega I1 Eye One User manual

GO4 Vega I1 Eye One
IP Camera
User manual
User manual
2014-01 V1.1
Dear users, the configuration for this camera is professional, so please
read the user manual carefully before using the camera.

GO4 VEGA I1 IP CAMERA USER MANUAL
2
If the user manual cannot help you to solve the problem, please call our technical
support center for solutions. We will update the content for the new functions without
notice.
1、Installation Environment
Keep away from high-temperature, heat source and direct sunlight;
Keep away from water and should the unit get wet, switch off the power
immediately.
Avoid using in damp environment; the reference range for operation humidity is
below 85%RH.
Avoid using in extreme hot or cold environment, the reference range for
operation temperature is -10C°~ +50C°
Please install it horizontally or on wall mounts, avoid strenuous vibration place and
do not put other equipments on top of the unit.
2、Transport and Handling
The package is specifically designed to ensure a safe delivery, so please do not
use a different one.
Do not move the ip camera from overheated to supercooled condition frequently,
otherwise it will frost and shorten the service life.
Do not move the item when is power on, otherwise the main board might be
damaged.
Notice:
1. Please check the power supply is working
2. Be careful not to hit the camera or subject it to strong impacts or shocks.
3. Do not directly touch the optical components for the image sensor, if necessary,
please place a clean and moistened cloth with alcohol and wipe the dirt gently;
When not in use, please place the dust cover on to the item to protect the image
sensor.
4. Do not aim the camera directly into the sun or at other intense light sources that
could affect the image quality (it is not the problem for the ip camera), also
shorten the service life for the image sensor.
5. Keep away from laser when it is working, otherwise the image sensor can be
damaged.
6. If the equipment is not working properly, please contact the store or the service
center, do not disassemble or modify the equipment in any way. （Problems
caused by unauthorized modification or repair should be at your own risk.）
Statement
Notice

GO4 VEGA I1 IP CAMERA USER MANUAL
3
Index
1!PRODUCT INTRODUCTION ........................................................................................................ 4!
1.1 PRODUCT SUMMARY ................................................................................................ 4
1.2 PACKAGE FOR TYPICAL PRODUCTION ........................................................................... 4
2!INSTALLATION GUIDE................................................................................................................. 5!
2.1 AP CONNECTION .................................................................................................... 5
2.2 WIRED CONNECTION TO LAN.................................................................................... 5
2.3 WIFI CONNECTING TO LAN ...................................................................................... 6
2.4 CONNECTING TO WAN ............................................................................................ 8
3!OPERATION OF IE BROWSER .................................................................................................. 9!
3.1 VIEW VIDEO .......................................................................................................... 9
3.2 DEVICE INFORMATION ............................................................................................10
3.2.1 Device status.............................................................................................10
3.2.2 Device alias setting....................................................................................10
3.2.3 Device date and time setting ....................................................................10
3.2.4 Local recording path..................................................................................11
3.3 DEVICE WEB SETTING ............................................................................................11
3.3.1 Basic network settings ..............................................................................11
3.3.2 AP settings ................................................................................................11
3.3.3 Wireless wifi settings.................................................................................12
3.3.4 Manufacture’s DDNS setting......................................................................12
3.3.5 Third party DDNS setting ..........................................................................12
3.3.6 UPnP settings ............................................................................................12
3.4 ALARM SETTINGS .................................................................................................13
3.4.1 Alarm service setting.................................................................................13
3.4.2 Mail Service Setting ...................................................................................14
3.4.3 FTP Service Setting ...................................................................................14
3.4.4 Alarm log ...................................................................................................15
3.5 USER AND DEVICE SETTING .....................................................................................16
3.5.1 Multi-device Setting...................................................................................16
3.5.2 User Settings .............................................................................................16
3.5.3 PTZ settings ..............................................................................................16
3.5.4 Maintain .....................................................................................................17
4!VISITING DEVICE BY OTHER SOFTWARE........................................................................... 17!
4.1 OTHER WEB BROWSER ...........................................................................................17
4.2 MOBILE PHONE SOFTWARE......................................................................................17
4.3 CENTRALIZATION CONTROL ....................................................................................17
5!PRODUCT FAMILY FOR GO4 VEGA IP CAMERAS ............................................................ 18!
5.1 GO4 VEGA I1 EYE ONE QUICK LOOK.......................................................................18
APPENDIX：GO4 VEGA I1 EYE ONE – AT A GLANCE ............................................................ 19!

GO4 VEGA I1 IP CAMERA USER MANUAL
4
1 Product introduction
1.1 Product summary
Thank you for choosing GO4 Vega I1 series IP camera, the IP Camera combines a
high quality digital video camera with network connectivity and a powerful web
server to bring clear video to your desktop from anywhere on your local network
or over the Internet. It is very suitable for family, shops, office building and so on.
Main features for L series：
®The video is compressed by MJPEG. There are three VGA/QVGA/QQVGA
video resolutions options. User can changes some parameters according to
their demands to satisfy his own visual preferences;
®Infrared LED for night vision covers 5m area to give 24 hours monitoring;
®Support 802.11b/g/n protocol for wireless monitoring;
®Support AP mode, the PC and mobile phone can be directly connected to
the camera by WiFI, no need for the router;
®Support motion detection, send alarm information by email and FTP;
®Support mobile phone view;
®Built in web server, all data is transferred through one port; it is easy for
user to do the network setting;
®Manufacture attached a label at the bottom of each IP Camera, it include
DDNS. When IP Camera is connected to the internet, this URL can be used
to visit the device;
®Manufacturer provides free software, support Multi-view, long time
recording, video playback etc;
1.2 Package for typical production
Accessory
Type
Power
adaptor
CD
Cable
Bracket
Stand
of
plastic
Antenna
I1 camera
5V
√
√
√
√
√
Notice:
®Please check carefully if all listed items are included in the package, if
anything is missing please contact vendor immediately.

GO4 VEGA I1 IP CAMERA USER MANUAL
5
2 Installation guide
2.1 AP connection
Power on the camera (Please check carefully output voltage of power adapter,
don’t insert incorrect adapter, otherwise it will damage the camera), after 2
minutes, the camera will work normally. You can use PC or mobile phone to
connect directly the camera by WiFi, as Figure 1.
Figure 1
1) Turn WLAN on in PC, and search available SSID, if searched AP SSID in device
label, then you can connect it, default password is 123456789.
2) After connecting the camera, it will assign IP address to PC (PC wifi IP address
need to be set to “obtain automatically”).
3) Open browser in PC, enter IP address of camera (AP default IP address is
192.168.246.1) then you can visit the camera (refer to 2.2).
Note: Please check the user manual of mobile phone software when you connect
to the camera by mobile phone.
2.2 Wired connection to LAN
Power on the IP camera, connect IP camera to router by network cable,
meanwhile, connect computer to the same router, example of figure 2.
Figure 2
Insert CD to computer driver, double click “LSearch_en.exe” in the CD, run the
software, click “Search”, select the device searched, click “Browse” to open

GO4 VEGA I1 IP CAMERA USER MANUAL
6
browser, it will pop up user login dialog, enter default user name (admin) and
password (123456) to login the camera as figure 3.
Figure 3
We suggest using IE kernel browser to view the video （it can provide more
functions, but user needs to install video player before viewing the video. Click
“OCX Download ” to download OCX and install it.
Notice:
®If you installed a firewall software in your PC, when you run the
LSearch_en.exe, you might get a prompt saying “whether you want to block
this program or not”, then you should choose not to block.
®You can hold on reset button on the camera for 10 seconds to restore factory
default should you forget user name and password, during the process, don’t
disconnect the power, otherwise the camera maybe damaged.
2.3 WIFI connecting to LAN
You can connect the camera with router by wireless connection, as figure 4.
Figure 4
Before connecting router by wifi, please connect them as chapter 2.2 to Login
camera and enter wifi setting, and then operate as the following step, example of
figure 5.

GO4 VEGA I1 IP CAMERA USER MANUAL
7
Figure 5
Enter the Wireless LAN Setting, click the “Scan” button, it will show you all the
wireless networks detected in the Wireless Network List column. Select one of
them and tick “Using Wireless Lan”, then the relevant data of the selected
wireless network will be shown in the following blanks. Input the password and
click “Submit”, the WIFI setting is completed. Unplug the cable, then you can
proceed to connect to router by wifi.
Notice: When the device is connected both WIFI and wired, it will firstly connect to
the wired network. If the camera enables DHCP to obtain IP address automatically,
the IP address won’t be the same in wired connection and wifi connection: in this
case we recommend to set a fixed IP address for the camera.

GO4 VEGA I1 IP CAMERA USER MANUAL
8
2.4 Connecting to WAN
You should connect the LAN network to WAN first and do the port forwarding,
connect as figure 6.
Figure 6
If visit IP Camera from WAN, you must do port forwarding on the router. Example
of figure 7.
Figure 7
Operation Steps:
1) After login the interface of the router, choose “Port Forwarding”
2) Choose “Add custom Service”
3) Input IP camera http port
4) Input IP address of IP camera, click “Apply”

GO4 VEGA I1 IP CAMERA USER MANUAL
9
After finishing the port forwarding, you can use WAN IP address of router and http
port of camera to visit the camera by remote computer as figure 6.
Notice: because the routers are different, the interface and settings will be too, so
please refer to the user manual of your router or consult with router manufacturer
in order to properly set port forwarding.
3 Operation of IE browser
3.1 View video
After installing the plug-ins, click “Mode 1 to view” as Figure 3 to view the video
(video as Figure 8, actual user interface might differ).
Figure 8
1）Audio, Talk, Record, Snapshot
You can click these buttons to perform audio, talk,
record and snapshot functions.
Note: about recording path, click button to enter setting interface, you can
set it in “Local Recording Path”, as figure 9.

GO4 VEGA I1 IP CAMERA USER MANUAL
10
Figure 9
2）Multipicture change button
If you add multi-devices in chapter 3.4.2 “multi-device setting”, it will connect
other device to display pictures automatically when changing to 4, 9 split screen.
In playing video area, you can select a picture to control audio, talk, record,
snapshot and PTZ control etc.
3）Viewing control area
You can control PTZ moving, picture reversal and mirror etc. when viewing video,
and can adjust picture parameters, including resolution, brightness etc.
The camera supports 16 preset points, you can set one place as preset point
when moving the PTZ to a place, also can call the preset point when the camera
move to another place, so the camera can return to set place.
Note: button can control work mode of IR LED. IR LED has two modes, auto
and forced close. In auto mode the IR LED will power on or off according to
environment light; in forced close mode the IR LED will be always off.
4）Setting device parameters
Click button to enter setting interface, you can set all parameters of the
camera described in chapter 3.2 to 3.5. Only administrator can login to set these
parameters.
3.2 Device information
3.2.1 Device status
The user can check “Device firmware version”,” Web UI version”, “Alias”, “AP
MAC” etc.
3.2.2 Device alias setting
The user can rename the camera for ease of use, i.e “Home”, “Office2” etc.
3.2.3 Device date and time setting
You can enable “Sync with NTP Server” when the device is connected to WAN, but
you need to select correct time zone where the camera is located, otherwise you
have to select“ Sync with PC time”.

GO4 VEGA I1 IP CAMERA USER MANUAL
11
Figure 10
Remark：Please carefully check the camera time, so it can be sure the alarm
accuracy.
3.2.4 Local recording path
The camera will automatically create a file folder named “Record files” when the
user doesn’t set “local recording path” and launch recording directly, and then
save recording file to the folder, as figure 11.
Figure 11
3.3 Device web setting
3.3.1 Basic network settings
The user can also enter the Basic Network Settings to set the IP address except
using the search software “LSearch_en.exe”. See below Figure 12.
Figure 12
Remark: The router connected to camera need to enable DHCP when the user uses
“obtain IP from DHCP server”; the routers enable DHCP by default.
3.3.2 AP settings
Example of chapter 2.1, the user can directly connect to the camera by mobile

GO4 VEGA I1 IP CAMERA USER MANUAL
12
phone and laptop with WiFi. The label with default AP SSID can be found at the
bottom of the camera, the default password is 123456789. The user can change
the SSID and password, but the password must contain 8 or more characters and
digits.
Figure 13
3.3.3 Wireless wifi settings
Please refer to chapter 2.2.
3.3.4 Manufacture’s DDNS setting
Each IP Camera has an unique ID label with DDNS on its bottom, it is unique. The
manufacturer has established a DDNS system and allotted a DDNS to every device,
the user only enters the website into the browser and connect to the camera from
remote PC, example of figure 14.
Figure 14
3.3.5 Third party DDNS setting
User can also use third party DDNS, such as www.dyndns.com.In this case the
user must apply for a free domain name from the DNS provider and fill the info into
the below blanks (Figure 15) and save the settings. Only then the domain name
can be used.
Figure 15
Notice：Using the third party domain name, if the http port is not 80, the port
number should be added to the domain name with colon. Example:
http://btest.dyndns.biz:81.Don’t enter port number when you use manufacturer’s
DDNS.
3.3.6 UPnP settings
If you enable UPnP, once the IP camera is connected to the LAN, it will

GO4 VEGA I1 IP CAMERA USER MANUAL
13
communicate with the router in the LAN and do the port forwarding with open
port of router automatically. In figure 16, you only tick “Using UPnP to Port
Mapping” to finish the setting.
Figure 16
Before using the UPnP function, please make sure the router’s UPnP function has
been enabled. Not all the routers support UPnP perfectly. Please test if the router
works well with the equipment, if not, we suggest you to disable this function and
set the port forwarding manually.
3.4 Alarm Settings
3.4.1 Alarm service setting
If the user needs to monitor a fixed area to check if there is any motion, it will
detect the motion and trigger the alarm. In the motion detect sensibility, the
smaller the value, the more is the sensitivity.
After triggering the alarm, you can adopt several alarm modes in armed time,
example of figure 17.
Link to the Preset when alarming: need to set preset point of the camera;
Send alarm info by email (an email include a picture); every alarm trigger a
email;
Send the snap to the FTP server, user can also set the interval time between
two pictures.
The device only triggers alarm when it detects any motion in armed time. User can
set schedule time to be “all the time”, also assign the armed time. Before you set
“Time Schedule”, please go to Date and Time settings to set the correct time for
the item.

GO4 VEGA I1 IP CAMERA USER MANUAL
14
Figure 17
3.4.2 Mail Service Setting
When the device detects motion, it can send an email to your selected email box,
but you need to set email service parameters correctly first. Example of figure 18,
click “Submit” to save these parameters, and then you can click “Test” to check if
the setting is successful.
Figure 18
3.4.3 FTP Service Setting
When motion is detected, the device will take a local picture and send them to a

GO4 VEGA I1 IP CAMERA USER MANUAL
15
designated FTP server, but the user needs to set the FTP setting correctly. As
figure 19, after the setting is finished, click “Test” to check your settings are
correct or not.
Figure 19
Notice：To use the FTP function, you need to apply a user with permission to write
and create submenu and some memory space.
3.4.4 Alarm log
You can inquire when the device performs alarm in alarm log.
Figure 20

GO4 VEGA I1 IP CAMERA USER MANUAL
16
3.5 User and device setting
3.5.1 Multi-device Setting
As Figure 21, User can add a maximum of 9 devices to view video simultaneously.
Click “refresh” button to check the device in the LAN. When click a device, will
popup setting dialogue and enter the device info, and click “Add” to add device.
After that, must click “Setup” button to save device.
Figure 21
3.5.2 User Settings
Figure 22
3.5.3 PTZ settings
Figure 23
Note: When you set cruise turns all the time, the camera will automatically stop

GO4 VEGA I1 IP CAMERA USER MANUAL
17
after cruising one hour.
3.5.4 Maintain
Figure 24
Click “Restore factory settings”, a pop up dialog will ask you if you’d like to restore
to factory settings, then the camera will restore factory settings and reboot after
your confirmation.
There are two types software in the camera, one is device firmware, another is
Web UI, and you can upgrade them respectively.
4 Visiting device by other software
4.1 Other web browser
Besides IE browser, you can visit the camera by Firefox, Safari, Chrome, Opera
browser etc., please select “Mode 2 to view”.
4.2 Mobile phone software
For more information, please see the user manual for mobile phone in attached CD,
or download the latest software and user manual in our website.
4.3 Centralization Control
IPCMonitor is a free software offered by factory, several devices on LAN and WAN
can be browsed at the same time. The software also supports snapshot, video
record, scheduled record, alarming and so on. The interface is as figure 25.

GO4 VEGA I1 IP CAMERA USER MANUAL
18
Figure 25
For more information, please refer to the <<IPCMonitor User Manual>> in CD.
5 Product family for GO4 Vega IP cameras
5.1 GO4 Vega I1 Eye One Quick Look
Figure 26
The camera adopts 300K pixels CMOS sensor, 3.6mm lens, built in PTZ and MIC,
11 pieces IR LED, audio out socket. It uses 5V power adaptor.
Photoresistor
IR LED
MIC
RJ45
DC Power
I/O Alarm
Antenna
Audio OUT

GO4 VEGA I1 IP CAMERA USER MANUAL
19
Appendix：GO4 Vega I1 Eye One – At a glance
Statement：
1. If you have any questions of the manual, please contact our technical
support.
2. This manual will be updated periodically; the company reserves the right
to update this manual without prior notice.
Video
compression
MJPEG
Resolution
VGA/QVGA/QQVGA
Max.
Framerate
30FPS
Audio
compression
ADPCM
Main software
function
Support HTTP, DHCP, IEEE 802.11b/g/n, NTP, FTP, SMTP,
P2Pprotocol etc;
Support motion detection;
three level of user authority;
PTZ preset point ;
support upgrading online
Lens
3.6mm
Pan/Tilt
Tilt 100°Pan 350°
Night vision
11pcs IR LED, 8m distance
Wi-Fi
Yes
Audio
Built in MIC, audio out
Power supply
5V, power consumption<6W
Work
condition
-10℃~ 50℃under 85%RH
Body size
135*103*127mm
Function
Product