Goboservice GOLIVE150 User manual

Goboservice Lighting by Sunland Optics SRL
Via Don Minzoni 14 , 89125 Reggio Calabria
[phone]
Via Lombardia 269, 20861 Brugherio (MB)
[phone]
www.goboservice.com
[e-mail]
INSTRUCTION MANUAL
ENGLISH

GOLIVE150
- 3 -
ENGLISH
Thank you for choosing our projector ! We inform you that this product was designed and realized to
guarantee you the best performance and to satisfy as much as possible your expectations and
requirements.
Please read carefully each part of this instruction manual before start to use the product and use it each
time you have some difficulties or doubt.
The following instruction manual is a key part of this purchasing. It must be carefully stored for a period
of not less 10 (ten) years, in a known place and easily accessible to all interested people.
The knowledge and respect of manual contents are essential in order to guarantee the correct and safe
installation, use and maintenance of the product.
The Goboservice by Sunland Optics SRL company disclaims all liability for damage to the projector or to
other property or persons deriving from installation, use and maintenance that is not carried out in
accordance with that reported in this instruction manual, which must always accompany the unit.
Moreover Goboservice by SunlandOptics SRL reserves the right to change the information in this
instruction manual at any time and without notice.

- 4 -
WWW.GOBOSERVICE.COM
SUMMARY
1. SAFETY INFORMATION ................................................................................................................................................... 5
2. PACKAGE CONTENT ........................................................................................................................................................ 7
3. PROJECTOR INSTALLATION .......................................................................................................................................... 8
3.1. FRONT SIDE VIEW OF PROJECTOR ..................................................................................................................... 8
3.2. BACK SIDE VIEW OF PROJECTOR......................................................................................................................... 8
3.3. LENS MOUNTING or SUBSTITUTION .................................................................................................................. 8
3.4. LAMP MOUNTING or SUBSTITUTION................................................................................................................. 9
3.5. ISTRUZIONI DI MONTAGGIO DEI GOBO.........................................................................................................10
3.6. ACCESSORIES POWER SUPPLY...........................................................................................................................11
4. USE OF PROJECTOR.......................................................................................................................................................12
4.1. CONNECTION OF PROJECTOR TO THE MAINS SUPPLY............................................................................12
4.2. PROJECTOR ORIENTATION..................................................................................................................................12
4.3. PROJECTED IMAGE FOCUS..................................................................................................................................12
5. THECNICAL DATA...........................................................................................................................................................13
6. POSSIBLE PROBLEMS - CAUSES AND SOLUTIONS..............................................................................................14
7. DIRECTIVES........................................................................................................................................................................14
8. DISPOSAL...........................................................................................................................................................................14
9. WARRANTY .......................................................................................................................................................................15
10. MAINTENANCE HISTORY ...........................................................................................................................................16

GOLIVE150
- 5 -
ENGLISH
1. SAFETY INFORMATION
Please read carefully the following safety instructions before do any operations. The product describes in
this instructions manual is a lighting fixture for the projection of a light beam. It is used usually to light,
with an high level of surface brightness, small areas on which to project decorative effects or fascinating
and special logos and images. The projector must be only used for the purpose it was designed and
built for. It is suitable to illuminate indoor and outdoor environments, any other use is not approved by
the manufacturer and for this reason disclaims any liability for damages resulting from improper or
incorrect use. This unit should be disposed of according to your country’s regulations regarding the
differentiated waste collection and disposal.
1. INSTALLATION –Please pay attention that during installation there is not any
hinders on the place on which the projector has to be installed. The projector
must be attached with dowels or screws or other anchorages suitable with the
material to be blocked. Make sure that all parts for fixing the projector are in a
good state of repair and check the stability of the point of anchorage before
positioning the projector.
2. MINIMUM DISTANCE OF ILLUMINATED OBJECTS –The projector must be
placed so that the objects hit by the beam of light are at least 2,0 meters from
the lens of projector.
3. MINIMUM DISTANCE FROM FLAMMABLE MATERIALS –The projector must be
placed so that the any flammable materials is at least 1,0 meters from every
point on the surface of the fitting.
4. MAXIMUM AMBIENT TEMPERATURE –Place the projector in a place where
there is a good air flow. Please don’t use it in closed or semi-closed
environments because this could cause an increase of temperature with a
reduction of projector life cycle. For a safe functioning of projector the
temperature must not exceed 45°C.
5. PROTECTION AGAINST INDIRECTS CONTACTS –It is mandatory connect the
projector to a mains supply system fitted with efficient earthing (Class I
appliance accableing to standard EN 60598-1). It is, moreover, recommended
to protect the supply lines of the projectors from indirect contact and/or
shorting to earth by using appropriately sized residual current devices.
6. CONNECTION TO MAIN SUPPLY - Connection to the electricity mains must be
carried out by a qualified electrical installer. Check that the mains frequency
and voltage correspond to those for which the projector is designed. Evaluate if
the mains supply can withstand the power consuption of projector and, if it is,
verify the maximum number of devices that it is possible connect to the
electricity line in order to avoid overloading.

- 6 -
WWW.GOBOSERVICE.COM
7. TEMPERATURE OF EXTERNAL SURFACE –The maximum temperature that can
be reached on the external surface of the fitting, in a thermally steady state, is
60°C.
8. PROTECTION RATING - Direct exposure of the projector to rain, snow, hail or
other liquids may damage the product. The projector must be kept away from
wet surfaces. ATTENTION: water must not touch the projector when it is
connected to the mains supply. To protect the unit from rain use the accessory
GOLIVE COVER.
9. MAINTENANCE - Before starting any maintenance work or cleaning the
projector, cut off power from the mains supply.
ATTENTION: According to guarantee conditions just the lamp substitution is
considered an allowed maintenance. If you need to replace the lamp, it is
recommended, after turning off the projector, to wait 15 minutes before
opening the cover to access the lamp. Now wait another 10 minutes before
touching the lamp to avoid burns. The product should never be washed, but
should be cleaned on the outside with only a slightly damp cloth. If a
replacement of other parts (engine, drive circuit or ballast, etc.) is needed
please contact your dealer in order to have more information as well as the
original parts. Not try to replace by themselves defective parts with not original
spare parts.
10. LAMP - Carefully read the "operating instructions" provided by the lamp
manufacturer. In order to know the supplied lamp please refer to the section
PACKAGE CONTENT of this manual. Immediately replace the lamp if damaged
or deformed by heat.
11. RISK OF VIEW - Never look the beam of the projector directly or with optical
instruments of convergence of the light.
12. RESIDUAL RISKS –Also if the product is built in compliance with all rules and
precautions, residual risks related to certain structural aspects of product usage
remain. Do not disassemble the device. Maintenance should be performed by
trained personnel. Do not tamper for any reason the ballast which is sealed for
safety reasons and should remain so. If ballast is tampered this represents a
serious danger and in this status the product is no more under warranty. Set
the unit in visible areas and pay attention that does not interfere with normal
passage of people, the risk of a collision must be minimized if not eliminated.
Do not place the unit in positions where it can fall hitting people or animals.
Keep children away from the unit when it is working and it is still connected to
the mains supply. In case of abnormalities in the coating or breakage of the
housing that contains bright spare parts, do not turn on the projector and stop
the use of the product. Do not install in areas available to minors or persons

GOLIVE150
- 7 -
ENGLISH
who could be affected by the use or misuse. The device if it is not connected to
mains supply it is not a danger for people and animals even when exposed to
rain. The projector works with electrical energy at low voltage and that puts it in
an area of dangerousness typical of a household appliance; it must be
considered, in any case, a lighting apparatus and, therefore, must be adopted
during use an appropriate attitude. The device is designed and constructed
using all safety criteria and suitable materials to prevent hazards and to
minimize risks.
2. PACKAGE CONTENT
Please check that the product is in perfect condition in all its parts when the good is delivered ; otherwise
contact the manufacturer immediatly. Take out goods from the package and check if they have any
damage caused by transport. The package should be disposed following your country’s regulations
regarding the differentiated waste collection and disposal.
-N°1 Projector GOLIVE150.
-N°1 CD-ROM that contains Instructions Manual and Warranty.
-N°1 Lamp 150W (OSRAM POWERBALL HCI-T 150W/942 NDL PB).
-N°1 Power Supply cable.

- 8 -
WWW.GOBOSERVICE.COM
3. PROJECTOR INSTALLATION
3.1. FRONT SIDE VIEW OF PROJECTOR
The Fig.1 shows the front panel of projector.
Element 1 It is an OUTPUT (POWER ACCESSORIES) at 12V to
use when some external accessories are needed
(see section 3.6 ACCESSORIES POWER SUPPLY).
Element 2 Is a quality lens camera with a 100mm optical
standard aperture.
Element 3 They are a pair of holes to be used when the
support bracket for external accessories is needed
(example: Prism Accessory).
Fig.1
3.2. BACK SIDE VIEW OF PROJECTOR
The Fig.2 shows the rear panel of projector.
Element 1 is the plug for the power supply cable.
Element 2 is the switch that manage the projector power supply.
Element 3 is a switch that can enable/disable the power supply for any
internal accessories (see section 3.6 ACCESSORIES POWER
SUPPLY).
Fig.2
3.3. LENS MOUNTING or SUBSTITUTION
The Fig.3 shows the front panel of projector and the four
screws highlighted are needed for the lens fixing using the
special support.
So for the lens mounting/substitution will be needed fix the
support with the four supplied screws as shown in Fig.3 and
mount the lens screwing it into the support.
Fig.3

GOLIVE150
- 9 -
ENGLISH
3.4. LAMP MOUNTING or SUBSTITUTION
For the lamp mounting/substitution it is needed act on the
panel that is located at the top of the projector (see Fig.4).
Provide yourself with a cloth in order to mount the lamp in
a proper and functional way.
The steps to follow are:
1. Unscrew the threaded knob (highlighted in Fig.4, lens
side) that fixes the panel at the top of the projector
and open the panel.
2. Unscrew the threaded knobs that fix the GOBO
HOLDER and that are located in the two sides of
projector as shown in Fig.5.
3. Take out the GOBO HOLDER from projector rotating it
as shown in Fig.6.
Fig.4
Fig.5
Fig.6
4. Install the lamp (that must be touched just with the cloth provided before) in the appropriate
housing, that is located at the center of the parabola of projection, and please pay attention to the
installation direction.
5. Insert again the GOBO HOLDER taken out before and pay attention to screw again the threaded
knobs needed to fix it.
6. Close the panel that is located at the top of the projector fixing it with the special threaded knob
unscrewed before.
ATTENTION: Please pay attention that the panel that is located at the top of the projector is closed
before switch on the projector (the lamp gives off rays that damage the eyes).
If internal accessories different from standard GOBO HOLDER are used (example: dynamic effect,
rotation effect, ecc.) the steps 2, 3 and 5 must be done following the installation instructions supplied
with the accessory.
The lamp mounting/substitution must be done when the projector is switched off and not connected to
the mains supply.
If the lamp must be substituted after the projector usage, wait (about 15 minutes) so that all internal
components of projector are cool.

- 10 -
WWW.GOBOSERVICE.COM
3.5. ISTRUZIONI DI MONTAGGIO DEI GOBO
The gobo has two main parameters that allow its mounting on
projector; these parameters are shown in Fig.7 and they are:
- the OD (Outer Diameter) which is the physical gobo diameter
- the ID (Inner Diameter) i.e. the circle diameter within which the
image to realize has to be contained.
For all GOLIVE projector series the gobos must have OD = 52,8 mm e
ID = 48 mm.
Fig.7
ATTENTION: During gobo installation /substitution into the projector it is necessary placing the gobo so
that the REFLECTING SIDE ALWAYS FACING TOWARDS THE LAMP; on contrary THE MATTED
(BLACK/GREY) SIDE MUST FACE TOWARDS THE PROJECTOR LENS (see Fig.8). This mounting rule allows
the correct usage of gobo avoiding its breaking.
LAMP
GOBO
LENS
Fig.8
Once the installation direction of gobo was understood, it is enough embed it between the two silicone
cylinders visible on GOBO HOLDER, doing a slight pressure on the gobo (see Fig.9). Pay attention that in
order to place the gobo it is necessary first take out the GOBO HOLDER from projector; for this
operation it is enough refer to the first three steps needed for the lamp mounting/substitution (see
section 3.4. LAMP MOUNTING or SUBSTITUTION).
Fig.9
Once the gobo was located, install again the GOBO HOLDER into the projector and close the panel of
projector with the special threaded knob; for this operation it is enough refer to the steps 5 and 6 of
section 3.4. LAMP MOUNTING or SUBSTITUTION.