Avtech AVALON400ZOOM User manual

AVALON400ZOOM
1030/1652
400W outdoor LED Gobo projector
10-30 / 16 - 52 zoom
USER MANUAL

1. Introduction
4 MODES：DMX mode, Manual mode , Slave Mode, Auto run mode
DMX Channels：13 channels
Main functions: dimming, color, rotating gobo wheel, focus, zoom, gobo flutter, prism
4 menu buttons: Long press MODE+SET for 3 seconds to unlock, press MODE+SET in other interface
to quickly lock
MODE Menu/Back to previous menu
SET Confirm the selection function
UP Select the previous option
DOWN Select the next option
2. Menu
Menu 1 Menu 2 Menu 3 Menu 4
1)DMX Address 001-512
2)Auto Mode Auto Run
Scene Edit Scene1-Scene7 1. Dimming: 0-255
2. Strobe: 0-255
3. Color: 0-255
4. Color_F: 0-255
5.Gobo: 0-255
6. GoboR: 0-255
7. Gobo_F: 0-255
8. Focus: 0-255
9. Zoom： 0-255
10. Flutter： 0-255
11. Prism： 0-255
12. Prism R: 0-255
13.Time: 0-255
3. Slave Mode
4. Manual
Control
1. Dimmer: 0-255
2. Strobe: 0-255
3. Color: 0-255
4. Color_F: 0-255
5. Gobo: 0-255
6. GoboR: 0-255
7. Gobo_F: 0-255
8. Focus: 0-255
9. Zoom： 0-255
10. Flutter： 0-255
11. Prism： 0-255
12. PrismR: 0-255
5. Settings 1. Curve Select 1.Linear

2.Square Law
3.InvSquareLaw
4.S-Curve
2.DMX Fail Off
Hold
3.Display Normal
Inverted
4.Key Lock Lock after 30s
Unlocked
5.Back Light Off after 60s
Always On
6.Reset No
Yes
7.Default No
Yes
6. Calibrations Password 1. Color: 0-255
2. Gobo: 0-255
3. GoboR: 0-255
4. Focus: 0-255
5. Zoom： 0-255
6. Flutter: 0-255
7. Prism: 0-255
8. Default
7.Information Version and UID
Menu description:
1. DMX Address
 Press the UP/DOWN button to set the initial address code (001 ~ 512). After setting the
address code, press the SET button to confirm the save and automatically exit to return
to the main menu. The fixture is in DMX mode after this operation.
2. Auto Mode
 Select the Auto Mode menu, there are two menus for option, one is Auto Mode, another
is Scene Edit with 8 scenes for editing. Each scene can be edited independently, and also
includes all the DMX channels function and time-keeping function, but no Reset function.
The editing process is the same as Manual Control, exit to save.
This fixture has a maximum of 8 gobos, so it can set 8 scenes. If you need less than 8
scenes, set the scene time-keeping to “0”. The unit of time is seconds.
3. Slave Mode
 Select the Slave Mode menu, press the SET button to enter Slave Mode, then it will
receive the signal from the master and keep the same state as the master. The fixture in
Auto Mode or Manual mode is the master.

 In the screensaver, it will switch to DMX mode in response to the channel sent from the
console whenever the master or slave receives the DMX512 signal.
4. Manual Control
 Select the Manual Control menu, Press the UP/DOWN button to select which function
to operate. The right number after pressing the SET button is selected. Then press the
UP/DOWN button to modify the value, long press to continuously modify, and press the
SET button to change the options on the left. Press the MODE button to exit and return
to the main menu. It will not exit the manual mode in this state. It’s need to enter other
modes for switching. For example, if you set the DMX address, then will enter the DMX
mode.
5. Settings
1) Curve Select
 To choose one of linear dimming/square curve dimming/inverse square curve
dimming/S-curve dimming. The characteristic of linear dimming is that the light output
brightness maintains a linear relationship with the channel value; square curve dimming
is relatively linear dimming, and the channel value range occupied in the low brightness
area is more, that is the low brightness area is more abundantly adjusted; the low
brightness area occupies few channels. When the channel value increases from 0 to up,
the brightness quickly becomes very bright, and it allocates more channel value ranges
in the high brightness area; the S-shaped curve is in the low brightness area Both the
high-brightness area and the high-brightness area are allocated, and the medium-
brightness area is few.
2) DMX Fail
 “OFF” (No DMX, lighting is off.), “HOLD” (No DMX, lighting keeps the original state).
3) Display
 The display reverse is used when the fixture is upside down.
4) Key Lock
 When using the key lock function, not key operation after 30 seconds, the key is locked.
Pressing the key in the locked state is invalid. It needs to press the MODE+SET key
combination for 3 seconds to unlock.
5) Back Light
 Select always on or 60S off if no operation
6) Reset
 In order to verify whether the motor is working normally, and whether to save it after
modifying the parameters, it can be perform a reset operation, like re-powering on.
7) Default

 Restore the DMX address and parameters into factory values. The default address is 1,
and the gray background option in the menu table is the default.
6. Calibrations
 Enter 088 on the Password interface and press SET to enter the Calibrations menu. When
the option on the left is selected, press the UP/DOWN button to select which function to
operate. After pressing the SET button, the number on the right is in the selected state.
At this time, press the UP/DOWN button to modify the value. Long press can be modified
continuously. After pressing the SET button again, it changes back to the left option as
the selected state. Press the SET button on the Default option to restore the default value.
7. Information
 Display the fixture software version and UID code of RDM.
三、DMX channels
Function DMX Value Setting 13 Channels
Dimmer 000-255 0~100% 1
Strobe 0-10 Always on 2
11-127 Random strobe slow to fast
128-255 Linear strobe slow to fast
Color 0~7 White 3
8~15 Color1
16~23 Color2
24~31 Color3
32~39 Color4
40~47 Color5
48~55 Color6
56~63 Color7
64~71 White+ Color 1
72~79 Color 1+ Color 2
80~87 Color 2+ Color 3
88~95 Color 3+ Color 4
96~103 Color 4+ Color 5
104~111 Color 5+ Color 6
112~119 Color 6+ Color 7
120~127 Color 7+ White
128~191 Clockwise rotation: fast to slow
192~255 Counterclockwise rotation: slow to
fast
Color_F 0-255 Fine adjustment of color wheel
(corresponding to a color change)
4
Gobo 0~8 Gobo 1 ( or White circle) 5
9~17 Gobo 2

18~26 Gobo 3
27~35 Gobo 4
36~44 Gobo 5
45~53 Gobo 6
54~62 Gobo 7
63~71 Gobo 7 shake from slow to fast
72~80 Gobo 6 shake from slow to fast
81~89 Gobo 5 shake from slow to fast
90~98 Gobo 4 shake from slow to fast
99~107 Gobo 3 shake from slow to fast
108~116 Gobo 2 shake from slow to fast
117~127 Gobo 1 shake from slow to fast
128~191 Clockwise rotation fast to slow
192~255 Counterclockwise rotation slow to
fast
GoboR 0~127 Static rotation by a certain angle 6
128~191 Clockwise rotation fast to slow
192~255 Counterclockwise rotation slow to
fast
GoboF 0-255 Gobo positioning fine-tuning 7
Focus 0~255 Focusing 8
Zoom 0~255 Zooming 9
Flutter 0~127 No action 10
128-255 Gobo flutter slow to fast
Prism 0~31 Prism close 11
32~255 Prism open
PrismR 0~127 No rotate 12
128~191 Clockwise rotation fast to slow
192~255 Counterclockwise rotation slow to
fast
Reset 0~9 No action 13
10~19 All reset after three seconds
20-255 No action
4. RDM Supported Parameters
Readable Writable RMD instruction value description customize
DISC_UNIQUE_BRANCH 0x0001 search
DISC_MUTE 0x0002 Lock
DISC_UN_MUTE 0x0003 Unlock
√ SUPPORTED_PARAMETERS 0x0050
Supported
instruction list

√ PARAMETER_DESCRIPTION 0x0051
Custom
instruction
description
√ DEVICE_INFO 0x0060
Device
Information
√
DEVICE_MODEL_DESCRIPTIO
N 0x0080
Product
model
description
√ MANUFACTURER_LABEL 0x0081 manufacturer
√ √ DEVICE_LABEL 0x0082 Device label
√ √ FACTORY_DEFAULTS 0x0090
Factory
defaults
√ SOFTWARE_VERSION_LABEL 0x00C0
Software
version
description
√ √ DMX_START_ADDRESS 0x00F0
starting
address
√ SENSOR_DEFINITION 0x0200
Sensor
definition
√ √ SENSOR_VALUE 0x0201 Sensor value
√ RECORD_SENSORS 0x0202
Record sensor
value
√ √ DISPLAY_INVERT 0x0500
Display
reversed
√ √ IDENTIFY_DEVICE 0x1000
Identify
device
√ RESET_DEVICE 0x1001 Reset device
√ CAPTURE_PRESET 0x1030
Capture
preset
√ √ PRESET_PLAYBACK 0x1031
Preset
playback
√ √ FAC_RUN_MODE 0xD320
Lamp
operation
mode √
√ FAC_SAVE_RUN_MODE 0xD321
Save
operating
mode √
*Instructions of lamp operation mode: data is 1 byte unsigned number, 0 means DMX mode,
1 means manual control mode, 2 means Auto run mode, 3 means slave mode.
*Save operation mode description: The 0xD320 instruction is only a temporary modification
of the operation mode. You need to use the 0xD321 instruction to save, write 1 to save the
current operation mode, and write 0 to restore the previously stored operation mode.