Cineversum Force 4K Administrator guide

Remote Codes
R599874

R599874 - Force 4K Remote codes
2
Changes
Cineversum provides this manual ‘as is’ without warranty of any kind, either expressed or implied, including but
not limited to the implied warranties or merchantability and fitness for a particular purpose. Cineversum may make
improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time
without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to
the information in this publication; these changes are incorporated in new editions of this publication.
Copyright
All right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be
recorded, transmitted or stored in a retrieval system without the prior written consent of Cineversum.
Guarantee
Cineversum provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of
guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during
transport, as well as for material and manufacturing faults. Cineversum must be informed immediately in
writing of any complaints. If the purchaser or third party caries out modifications or repairs on goods delivered
by Cineversum, or if the goods are handle incorrectly, in particular if the systems are commissioned operated
incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all
guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system
failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces.
Normal wear as well as normal maintenance are not subject to the guarantee provided by Cineversum either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must
be complied with by the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of
their respective holders. All brands and product names mentioned in this manual serve as comments or examples
and are not to be understood as advertising for the products of their manufactures.

R599874 - Force 4K Remote codes 3
1.1  ListofOperatingcommands
· Connection check .........................................................................................................4
· Power ............................................................................................................................4
· Inputs ............................................................................................................................4
· Initial Setup ...................................................................................................................4
· Picture Mode.................................................................................................................4
· Color Profile ..................................................................................................................4
· Gamma Table................................................................................................................5
· Contrast ........................................................................................................................5
· Brightness.....................................................................................................................5
· Color .............................................................................................................................5
· Tint................................................................................................................................5
· Dynamic Control ...........................................................................................................5
· Noise Reduction............................................................................................................5
· Bright Level (white) .......................................................................................................5
· Dark Level (white) .........................................................................................................5
· Low Latency Mode........................................................................................................5
· CMD 400Hz ..................................................................................................................5
· Motion Enhance............................................................................................................5
· Lens Aperture ...............................................................................................................5
· Laser Diode Power........................................................................................................5
· Graphic Mode ...............................................................................................................5
· MPC Enhance ..............................................................................................................5
· MPC Smoothing............................................................................................................5
· Set User names ............................................................................................................5
· HDMI Input Level ..........................................................................................................5
· HDMI Color Space........................................................................................................5
· Input Aspect Ratio.........................................................................................................5
· Mask switch ..................................................................................................................5
· 3D Parallax....................................................................................................................5
· 3D Crosstalk Cancel .....................................................................................................5
· Select 3D mode ............................................................................................................5
· 3D Left / Right phase ....................................................................................................6
· Anamorphic Modes.......................................................................................................6
· Load a specific Installation Mode..................................................................................6
· Set Inst. Mode names ...................................................................................................6
· Expert Calibration (THX)...............................................................................................6
· Expert Calibration (ISF) ................................................................................................6
· Set Calibrator names ....................................................................................................6

R599874 - Force 4K Remote codes
4
1.2  RS-232Cprotocol
Serial communication specifications
Control of this unit is possible using a computer or automation device connected with a RS-232 cross cable
(female - female D-sub 9 pins cable) or LAN/ RJ-45 cable. Communication specifications for this unit are as
follows:
Baud Rate 19200 bps
Data Format Binary
Mode Asynchronous
Parity None
Start Bit 1 bit set to high
Stop Bit 1 bit set to low
X on/off None
Flow Control None
RS-232C pin assignation
Pin Signal Function Signal Direction
2 RxD receive data PC -> this unti
3 TxD transmit data this unit -> PC
5 GND ground -
1, 4, 6-9 NC - -
Command Format
Header 1 Header 2 Command Command Data End of Data
21h 89h 01h 2 bytes 2 to 4 bytes 0Ah
Header 1: fixed to 21h for operating commands or 3Fh for reference command.
Header 2 fixed to 89h 01h
Command: 2-4 bytes length
Command Data: variable length between 1 and 4 bytes
End of Data fixed to 0Ah
Operating commands
Function Command Command Data Description
Connection check 00h 00h none Check the connection in standby mode
Power 50h 57h 30h / 31h Switch Off (Standby mode) / On.
Inputs 49h 50h 36h / 37h Switch active input to HDMI1 / HDMI2
Initial Setup 53h 55h 52h 43h 30h Switch RCU codes to A
52h 43h 31h Switch RCU codes to B
Picture Mode 50h 4Dh 50h 4Dh 30h 30h / 30h 31h Film Mode / Cinema Mode
30h 33h / 30h 34h Natural Mode / HDR Mode
30h 36h THX Mode
30h 43h / 30h 44h User 1 / User 2
30h 45h / 30h 46 User 3 / User 4
31h 30h / 31h 31h User 5 / User 6
50h 52h xx special Switch to next picture mode
Color Profile 50h 4Dh 50h 52h 30h 30h Off
30h 31h / 30h 32h Film1 / Film2
30h 33h BT.709
30h 34h / 30h 36h Cinema / Anime
1
6
5
9

R599874 - Force 4K Remote codes 5
Function Command Command Data Description
Color Profile 50h 4Dh 50h 52h 30h 41h / 30h 42h HDR / BT.2020
30h 44h / 32h 31h THX / DCI
30h 45h / 30h 46h Custom1 / Custom2
31h 30h / 31h 31h Custom3 / Custom4
31h 32h / 32h 32h Custom5 / Custom6
Gamma Table 50h 4Dh 47h 54h 30h 30h / 30h 31h 2.2 / Cinema 1
30h 32h / 30h 34h Cinema 1 / Custom 1
30h 35h / 30h 36h Custom 2 / Custom 3
30h 37h / 30h 43h Hybrid Log / ST.2084
30h 38h / 30h 39h 2.4 / 2.6
30h 41h / 30h 42h Film 1 / Film 2
31h 30h THX
Contrast 50h 4Dh 43h 4Eh 4 bytes integer Set contrast to +10 -> 30h 30h 30h 41h
+15 -> 30h 30h 30h 46h
-1 -> 46h 46h 46h 46h
-15 -> 46h 46h 46h 31h
Brightness 50h 4Dh 42h 52h 4 bytes integer same as Contrast
Color 50h 4Dh 43h 4Fh 4 bytes integer same as Contrast
Tint 50h 4Dh 54h 49h 4 bytes integer same as Contrast
Dynamic Control 50h 4Dh 44h 43h 30h / 31h / 32h Off / Mode 1 / Mode 2
Noise Reduction 50h 4Dh 52h 4Eh 4 bytes integer same as Contrast
Bright Level (white) 50h 4Dh 52h 57h 4 bytes integer same as Contrast
Dark Level (white) 50h 4Dh 4Bh 57h 4 bytes integer same as Contrast
Low Latency Mode 50h 4Dh 4Ch 4Ch 30h / 31h Off / On
CMD 400Hz 50h 4Dh 43h 4Dh 30h / 33h / 34h / 35h Off / Low / High / Inverse Telecine
Motion Enhance 50h 4Dh 4Dh 45h 30h / 31h /32h Off / Low / High
Lens Aperture 50h 4Dh 4Ch 41h 4 bytes integer same as Contrast
Laser Diode Power 50h 4Dh 4Ch 50h 30h / 31h / 32h Normal / High / Mid
Graphic Mode 50h 4Dh 47h 4Dh 30h / 31h 2K / 4K
MPC Enhance 50h 4Dh 45h 4Eh 4 bytes integer same as Contrast
MPC Smoothing 50h 4Dh 53h 54h 4 bytes integer same as Contrast
Set User1 name 50h 4Dh 55h 31h 10 ASCII char. Set custom name to User1 Picture Mode
Set User2 name 50h 4Dh 55h 32h 10 ASCII char. Set custom name to User2 Picture Mode
Set User3 name 50h 4Dh 55h 33h 10 ASCII char. Set custom name to User3 Picture Mode
Set User4 name 50h 4Dh 55h 34h 10 ASCII char. Set custom name to User4 Picture Mode
Set User5 name 50h 4Dh 55h 35h 10 ASCII char. Set custom name to User5 Picture Mode
Set User6 name 50h 4Dh 55h 36h 10 ASCII char. Set custom name to User6 Picture Mode
HDMI Input Level 49h 53h 49h 4Ch 30h / 31h / 32h / 33h Standard / Enhanced / Super White / Auto
HDMI Color Space 49h 53h 48h 52h 30h / 31h / 32h / 33h Auto / YCbCr(4:4:4) / YCbCr(4:2:2) / RGB
Input Aspect Ratio 49h 53h 41h 53h 32h / 33h / 34h Zoom / Auto / Just
Mask switch 49h 53h 4Dh 41h 31h / 32h On / Off
3D Parallax 49h 53h 4Ch 56h 4 byte integer same as Contrast
3D Crosstalk Cancel 49h 53h 43h 41h 4 byte integer same as Contrast
Select 3D mode 49h 53h 33h 44h 31h 3D mode set to Auto
33h 3D mode set to Side by Side
34h 3D mode set to Top & Bottom
30h 3D mode is disable (force 2D mode)

R599874 - Force 4K Remote codes
6
Function Command Command Data Description
3D Left / Right phase 49h 53h 33h 50h 30h Standard phase L/R
31h Inverse phase R/L
Anamorphic Modes 49h 4Eh 56h 53h 30h Turn Off the Anamorphic mode
31h Anamorphic mode set to Mode A
32h Anamorphic mode set to Mode B
Load a specific
Installation Mode
49h 4Eh 4Dh 4Ch 30h Select Installation Mode 1
31h. Select Installation Mode 2
...
39h Select Installation Mode 10
Inst. Mode 1 name 49h 4Eh 4Dh 31h 10 ASCII char. Set custom name to Installation Mode 1
Inst. Mode 2 name 49h 4Eh 4Dh 32h 10 ASCII char. Set custom name to Installation Mode 2
...
Inst. Mode 9 name 49h 4Eh 4Dh 39h 10 ASCII char. Set custom name to Installation Mode 9
Inst. Mode 10 name 49h 4Eh 4Dh 41h 10 ASCII char. Set custom name to Installation Mode 10
Expert Calibration
(THX)
52h 43h 37h 33h 43h 36h THX plus - On and Adjust
37h 33h 43h 37h THX plus - Off
37h 33h 43h 38h THX plus - On locked
37h 33h 38h 35h Switch Picture Mode to THX - Bright
37h 33h 38h 36h Switch Picture Mode to THX - Dark
Expert Calibration
(ISF)
52h 43h 37h 33h 35h 38h ISF - On and Adjust
37h 33h 35h 41h ISF - Off
37h 33h 35h 42h ISF - On locked
37h 33h 36h 34h Switch Picture Mode to ISF - Day
37h 33h 36h 35h Switch Picture Mode to ISF - Night
Set Calibrator name 50h 4Dh 43h 49h 18 ASCII char. Set Calibrator name - ISF must be “Adjust”
Examples
You want to... Command to send
Switch this unit On send: 21h 89h 01h 50h 57h 31h 0Ah
receive: 06h 89h 01h 50h 57h 0Ah
Switch this unit Off send: 21h 89h 01h 50h 57h 30h 0Ah
receive: 06h 89h 01h 50h 57h 0Ah
Change active Input to HDMI2. send: 21h 89h 01h 49h 50h 37h 0Ah
receive: 06h 89h 01h 49h 50h 0Ah
Change Picture Mode to match HDR send: 21h 89h 01h 50h 4Dh 50h 4Dh 30h 34h 0Ah
receive: 06h 89h 01h 50h 4Dh 50h 4Dh 0Ah
Change Aspect Ratio to Anamorphic A send: 21h 89h 01h 49h 4Eh 56h 53h 31h 0Ah
receive: 06h 89h 01h 49h 4Eh 56h 53h 0Ah
Change Installation Mode 2 Name to
“Widescreen” (unused character are filled
with space = 20h)
send: 21h 89h 01h 49h 4Eh 4Dh 32h 0Ah
receive: 06h 89h 01h 49h 4Eh 4Dh 32h 0Ah
send: 57h 69h 64h 65h 73h 63h 72h 65h 65h 6Eh
receive: 06h 89h 01h 49h 4Eh 4Dh 32h 0Ah

R599874 - Force 4K Remote codes 7
1.3  LANControl
Sending a LAN Control Command
In order to send a Remote Control compatible command to this unit, you must open a TCP connection on port
20554. and send a command immediately as the connection will be dropped within 5 sec of inactivity. If for any
reason you have to change the TCP connection port, you may use the following RS-232c/LAN command.
[4Ch 53 50h 54h] + 4 ASCII chars as new port address in hexa
You want to set TCP port to 10000 Command to send
Send 10000 as new TCP port value:
10000 is 2710h in hexa, converted in
ASCII characters: 32h 37h 31h 30h
send: 21h 89h 01h 4Ch 53h 50h 54h 32h 37h 31h 30h 0Ah
receive: 06h 89h 01h 4Ch 53h 0Ah
Then, reboot Network module send: 21h 89h 01h 4Ch 53h 52h 53h 0Ah
receive: 06h 89h 01h 4Ch 53h 0Ah
Projector
2. Projector Ready
(PJ_OK)
4. Projector Acknowledge
(PJACK)
6. Projector confirms
`Control Device
1. Opening Connection
on port 20554
3. Command Type
(PJREQ)
5. Command
After 5sec,
connection is closed
LAN communication protocol and timed out
Examples
You want to... Command to send
Switch this unit On 1. open TCP connection
2. receive PJ_OK: 50h 4Ah 5Fh 4Fh 4Bh
3. send PJREQ: 50h 4Ah 52h 45h 51h
4. receive PJACK: 50h 4Ah 41h 43h 4Bh
5. send Power On cmd: 21h 89h 01h 50h 57h 31h 0Ah
6. receive confirmation: 06h 89h 01h 50h 57h 0Ah
after 5 sec, TCP connection is closed.
Switch Anamorphic to mode A 1. open TCP connection
2. receive PJ_OK: 50h 4Ah 5Fh 4Fh 4Bh
3. send PJREQ: 50h 4Ah 52h 45h 51h
4. receive PJACK: 50h 4Ah 41h 43h 4Bh
5. send Anamo A: 21h 89h 01h 49h 4Eh 56h 53h 31h 0Ah
6. receive confirmation: 06h 89h 01h 49h 4Eh 56h 53h 0Ah
after 5 sec, TCP connection is closed.