Goldline GL301BZNG Specifications

Goldline N17- manual Oct. 2017
1
Gas Built-in Hob
Model Number GL301BZNG GL302BZNG GL2BZNG GL3BZNG GL4SSNG GL4BZNG
GL301BZLPG GL302BZLP G GL2BZLPG GL3BZLPG GL4SSLPG GL4BZLPG
GL301BZNG- GL302BZN GL2BZNG- GL3BZNG- GL4SSNG-
GL4BZNG-CAST
CAST G-CAST CAST CAST CAST
GL301BZLPG GL302BZLP GL2BZLPG- GL3BZLPG- GL4SSLPG- GL4BZLPG-CAST
-CAST G-CAST CAST CAST CAST
GL2WZ NG
GL2WZLPG
GL3WZNG
GL3WZLP
G
GL603 BZNG
GL603 BZLPG
GL603WZNG
GL603WZLPG
GL4WZNG
GL4WZLP
G
GL2WZNG-
GL3WZNG-
GL603BZNG-
GL603WZNG-CAST
GL4WZNG-
CAST
CAST
CAST
CAST
GL2WZLPG-
GL3WZLPG-
GL603BZLPG-
GL603WZLPG-CAST
GL4WZLPG-
CAST
CAST
CAST
CAST
INSTALLATION INSTRUCTIONS (FOR FITTERS ONLY)
&
USER AND OPERATOR
INST RUCTIONS
Installation must be in accordance with manufacturer’s instruction, relevant Gas
Fitting Regulations or AS5601 – “Gas Installation” regulations.
These instructions should be read carefully prior to initial use and retained in a safe
place in order that full advantage can be taken of the features of your HOB COOKER.
REMINDER :
ANY SERVICING AND INSTALLATION OF THE H
OTPLATE
MUST BE CARRIED OUT BY AN AUTHORIZED PERSON .
ANY QUERIES SHOULD BE FORWARDED TO:
MANUFACTURER: A’VARD INDUSTRIES P/L.
ADDRESS: 58-60 Quantum Close, South Dandenong, Victoria 3175, Australia.
TEL: [phone]
Email: [email protected]m.au
WEBSITE: www.goldlinecor .com.au

2
Goldline N12- manual-ULPG June 2016
Diagram A
Tray Dimensions (in mm) Model : GL301BZNG/GL301BZLPG
GL301BZNG-CAST/GL301BZLPG-CAST
Diagram B
Cut-Out (in mm)
480 485
Diagram A
Tray Dimensions (in mm) Model : GL302BZNG/GL302BZLPG
GL302BZNG-CAST/GL302BZLPG-CAST Diagram B
Cut-Out (in mm)
480 485
Diagram A
Tray Dimensions (in mm)
Model : GL2BZNG / GL2BZLPG / GL2BZNG-CAST / GL2BZLPG-CAST
GL2WZNG / GL2WZLPG / GL2WZNG-CAST / GL2WZLPG-CAST
Diagram B
Cut-Out (in mm)
Diagram A
Tray Dimensions (in mm)
Model : GL3BZNG / GL3BZLPG / GL3BZNG-CAST / GL3BZLPG-CAST
GL3WZNG / GL3WZLPG / GL3WZNG-CAST / GL3WZLPG-CAST
GL3SSNG / GL3SSLPG / GL3SSNG-CAST / GL3SSLPG-CAST
Diagram B
Cut-Out (in mm)

Goldline N17- manual Oct. 2017
3
Diagram A
Tray Dimensions (in mm)
Model : GL603BZNG / GL603BZLPG / GL603BZNG-CAST / GL603BZLPG-CAST
GL603WZNG / GL603WZLPG / GL603WZNG-CAST / GL603WZLPG-CAST
Diagram B
Cut-Out (in mm)
Diagram A
Tray Dimensions (in mm)
Model : GL4BZNG / GL4BZLPG / GL4BZNG-CAST / GL4BZLPG-CAST
GL4WZNG / GL4WZLPG / GL4WZNG-CAST / GL4WZLPG-CAST
GL4SSNG / GL4SSLPG / GL4SSNG-CAST / GL4SSLPG-CAST
Diagram B
Cut-Out (in mm)
Diagram A Model : GL704BZNG / GL704BZLPG / GL704BZNG-CAST / GL704BZLPG-CAST
GL704WZNG / GL704WZLPG / GL704WZNG-CAST / GL704WZLPG-CAST
Diagram B
Tray Dimensions (in mm) Cut-Out (in mm)

4
Goldline N12- manual-ULPG June 2016
INSTALLATION INSTRUCTIONS
DATA PLATE DETAILS:
CHECK THAT THE DATA PLATE SHOWS THAT THE APPLIANCE IS SUITABLE FOR THE
AVAILABLE GAS SUPPLY.
IMPORANT: VERIFY GAS TYPE WITH LOCAL GAS NETWORK
OPERATOR BEFORE CONNECTION OF THIS APPLIANCE.
1. Room Ventilation
Not for use in Marine craft, caravans or Mobile homes unless
fitted with safety device.
2. Before installing the appliance check that the location provides the required
clearances from combustible materials and if necessary provide protection to adjacent
surfaces as required by the regulations. Make provision for the gas supply to be
connected in the position shown in Diagram A.
3. Cut the opening in the bench top to the dimensions shown in diagram B.
4. Remove the hotplate from the carton.
Position of gas inlet: See diagram on page 3. Depth from top of glass to bottom of tray:
70mm excluding regulator
5. Install the hotplate in the cut-out (see diagram B on page 2).
Note:
If clearance between side and rear walls and periphery of the burner is less than 250mm,
the walls must be protected with a non-combustible material. The protection must extend
a minimum distance of 450mm above the burner. Horizontal surfaces less than 650mm
vertically above the hotplate must also be protected.
6. Ensure that gas and electrical outlet are accessible with the appliance installed.
The gas connection to the regulator is 1/2” BSP. Please ensure gas supply line to
This cooktop must be installed in a room that has permanent ventilation to effect the
correct operation of the appliances and also to provide adequate ventilation.
This airflow must exceed 20m3 via permanent vented openings in the wall of the
room and these must have a section of 100cm² minimum. They must be constructed
In a manner so as to avoid any possible blockages. The airflow can also be drawn
indirectly from an adjacent room provided it complies with any local regulations to
vent any fumes outdoors.
the appliance is of adequate length to allow sufficient withdrawal of appliance for
service or disconnection. The connection must be annealed copper pipe or flexible
hose (if permissible by local aythority).
The data plate is located on the tray oor.
Refer - Gas fitting Manual. Not Supplied (AS5601)

Goldline N17- manual Oct. 2017
5
7. Use a spanner at the flat area provided to hold the regulator firmly, when making
the join. Refer diagram below.
8. Once they are tightened
securely, turn the gas on and
check for leaks using a soap
solution and brush around all
joints and connections.
Pressure test point for LP gas only.
Use the regulator provided for town and natural gas.
Pressure test point:
- This is provided in the gas regulator.
- Remove the screw; connect the hose from the pressure gauge.
- Turn on the gas to the large burner and manually light the burner.
- The pressure is shown on the data plate.
- To increase the pressure, loosen locking nut and turn clockwise.
- Disconnect gauge and replace test point screw.
9 . Test the appliance
- The burner will ignite. Adjust control knob to desired setting. Normally, no adjustment
should be necessary.
- Depress each control knob and turn to full flame setting.

6
Goldline N12- manual-ULPG June 2016
10. Please make sure that gas supply connection is easily accessible for servicing or
other purpose.
11. Stick the second data label (which is provided in the box) at a place, which is
noticeable, e.g.: inside the cabinet door or the sidewall.
12. Instruct the user to keep the user instruction manual.
If any of the above procedures do not produce satisfactory results, the agent’s service
department should be consulted for more specialize assistance.
13. Please note that the cooktop is fitted with flame failure device that cuts off the
gas supply when burner flame extinguishes suddenly or abnormally in order to avoid
gas leakage.
W ARNING!
NOT FOR USE IN MARINE CRAFT, CARAVANS OR MOBILE
HOMES
UNLESS FITTED WITH SAFETY DEVICE.
WARNING:
- DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
- SOME PROPELLANT GASES CAN BREAK DOWN WHEN HEATED AND PRODUCE CORROSIVE
VAPOURS, WHICH WILL ATTACK SOME MATERIALS.
- ARTICLES, WHICH ARE MADE OF FLAMMABLE MATER SHOULD NOT BE STORED IN DRAWERS
OR CUPBOARDS IMMEDIATELY BELOW THIS APPLIANCE.
- THE SILICONE RUBBERGASKET SHOULD NOT BE REMOVED UNDER ANY CIRCUMSTANCES. IN
THE EVENT THAT ANY PROTECTIVE RUBBERGASKET IS DROPPED OFF OR DAMAGED, THE
CONSUMER SHOULD CEASE FORTHWITH THE USE OF THE UNIT UNTIL IT IS DULY RECTIFIED.
- DO NOT STORE ARTICLES WITHIN 50MM OF THE BOTTOM OF THE HOTPLATE CASING.
- DO NOT TOUCH SPARK IGNITOR WHILE LIGHTING THE BURNER.
- WHEN THE APPLIANCEIS INSTALLED IN A MARINE CRAFT OR IN A CARAVAN, IT SHALL NOT BE
USED AS A SPACE HEATER.
- DO NOT MODIFY THIS APPLIANCE.
- if any problem occurs, refer to the servicing instruction of the faultfinding chart.

Goldline N17- manual Oct. 2017
7
SERVICING INSTRUCTIONS
WARNING! DANGER 220
VOLTS 50Hz
.
DISCONNET POWER BEFORE SERVICING UNIT
DO NOT MODIFY THIS APPLIANCE
MINOR ADJUSTMENT
Access to By Pass Screw
- Light the burner and turn to
minimum setting (marked small
minimum setting and should not
extinguish when passing from
maximum setting to low setting.
- If adjustment is necessary, remove
the control knob by pulling upward.
The bypass screw is accessible
via the control knob spindle. Turn
the bypass screw anti-clockwise to
increase the turn-down rate
Access to manifold, gas taps and burner
assembly
- Remove glass hob and control knobs.
- To remove gas cocks. Unscrew the locking nut
(between cock and burner). Remove screws, the
cock can now be removed from the manifold.
If access to the barrel is required, remove two
screws, which retain spindle to body. If lubricating
the mechanism use Regosine Moly LM or other
approved grease.
To replace electrode
- Remove screw from the clamp holding the
electrode and thermocouple and note the
adjustment setting height of each. Replace electrode
FAULT ISOLATION CHART
FAULT
CAUSES
REMEDY
Burner will not light
1. Air in gas line
2. Blockage in line
3. Ignition not sparking
4. Flame failure device faulty
5. Check the battery
(applicable to DC version)
1. Purge gas line
2. Trace back and clear
3. Check lead and electrode
4. Replace thermocouple and test
5. Replace the battery
Burner lights back to
injector
1. Excessive lint up burner
mixing tube
2. Excessive gas pressure
1. Remove and clean burner
2. Check gas regulator pressure.
Adjust if necessary.
Burner has explosive
ignition
1. Excessive gas pressure 1. Check gas regulator pressure.
Adjust if necessary.
Ignitor not sparking
1. Electrode gap
2. Ignition connection
1. Check gap, adjust if not
between 4-5mm
2. Check connection to ignitor,
replace if faulty.
or contact the product manufacturer.
flame).
The flame should
and then fit clamp and screw.
if any problem cannot be rectified please contact the agent in your state or the gas supply authority service department

8
Goldline N12- manual-ULPG June 2016
OPERATING INSTRUCTIONS
IGNITION
This hotplate is equipped with electronic ignition to each of the burners and is
operated by depressing the individual control knob and turning it a quarter turn anti-
clockwise.
MANUAL IGNITION
If there is no power to the appliance or your are is experiencing a power black-out, simple
strike a match or spark igniter next to the required burner and follow the instruction above.
Note: the flame safety systems independent of power and will still operate without a power
source. Should your cooktop fail to ignite after manual procedure has been followed then
check to see that the gas supply to appliance has not been shut off.
CONTROLS
The Hobcooker has the control knobs, which are situated, at the front of the glass plate. An
indicator motif advises which knob controls each burner. The ‘full-on’ and pre-set ‘simmer’
BURNER OPERATION
1. Depress the required control knob anti-clockwise to the FULL-ON position.
2. When the burner has ignited, adjust the control knob to the required setting. Flame
adjustment is achieved by rotating the control knob further in an anti-clockwise fashion
BATTERY REPLACEMENT (applicable to battery ignition model)
2. Remove old battery
3. Replace with new 1.5 Volt “D” size battery noting correct polarity
Open the battery holder cover flap
Close cover flap
The hob cooker is unique in its burner design and layout. They delivery up to one and
a half times the flame heat and spread compated to normal hi-speed burners. All burners
retain normal simmer cooking facilities. The widely spaced positioning of the burners allows
for the use of large woks.
positions are indicated by a large and small flame graphic on the glass plate next to each
individual control knob.

Goldline N17- manual Oct. 2017
9
CLEANING
-
-
- Do not wash burner caps in a dishwasher.
- For ease of cleaning, remove spillage from the bowls as soon as possible. Control
knobs may be pulled off for cleaning beneath them, but take care not to allow water to
enter the holes in the glass plate.
- When re-assembling the spillage bowl always ensure that it is correctly located over
the spark electrode. Care should be taken to keep the electrode clean and avoid
damage to the porcelain insulator when removing the spillage bowl during cleaning.
- It is recommended that the appliance should be clean as describe above daily for
optimal performance and longer life expectancy.
- Wash spill bowl regularly and clean dirt and grease in a weekly basis.
- Check the burner port regularly for blockage especially if there is occurrence of
spillage and clean them if necessary.
MAINTENANCE SCHEDULE
- It is recommended that to have the units serviced by an authorized person at least
once a year.
Allow the hob cooker to cool before attempting to dismantle or clean it. The glass
plate is best cleaned with a cloth, using warm soapy water. Use of abrasive powders
and pastes should be avoided as far as possible, but when necessary use only a mild
abrasive. For removal of hardened grease, very fine steel wool, wetted and liberally
soaped, can be used.
Caustic solutions, washing soda, aerosol spray cleaners, bleach and some biological
cleaners are detrimental to some surface finishes and care must be taken not to
apply them to the burner bodies and caps.

10
Goldline N12- manual-ULPG June 2016
HINTS ON THE USE OF THE HOTPLATE
Utensils should always be placed centrally on the pan supports and over the burners.
Flames which extend beyond the bottom of utensils are wasteful and can damage or
overheat handles. Large diameter utensils (greater than 200mm in diameter) must not be
allowed to protrude beyond the perimeter of the hotplate, as this could cause overheating or
damage to the adjacent bench.
Do not remove the pan support and enclose the burner with a wok
hotplate.
Do not use large pots or heavy weights which can bend the pan support
Locate pan centrally over burner so that it is stable and does not
overhang the appliance.
Use only wok support supplied or recommended by the manufacturer of
the appliance.
SAFETY HINTS.
Always turn panhandles to the side or back of the hotplate – not out into the kitchen where
operation, due to the possibility of fabric ignition, which may result in personal injury.
MINOR TROUBLE SHOOTING.
Symptoms
Please check the following:
NO IGNITION
1. Check if anything is obstructing the electrode metal tip.
2. If 240 AC: check if appliance is connected to electrical supply.
3. If 1.5V battery: check and replace battery if required.
NO GAS
Check that the gas is turned on at the main meter.
BURNER FLAME NOT
BURNING EVENLY
Check the burner head is sitting evenly and that the slots in the
burner head are not obstructed. In the event that you are not
consulted.
Note:
phone number provided in this manual.
Do not place anything, e.g. flame tarner, asbestos mat, between pan
and pan support as serious damage to the appliances may result.
stand as this will concentrate the flame and deflect the heat onto the
or deflect the flame onto the hotplate.
satisfied with the hotplate, the distributor in your State should be
Should you still experience difficulties with your Goldline cook top please contact the manufacturer at the address and
they can easily be knocked. Do not weat loose fitting garments while the burners are in

Goldline N17- manual Oct. 2017
11
RECOGNISING ABNORMAL OPERATION
Turn off the unit immediately. Stop using the unit.
Call authorized person or contact the manufacturer.
W ARNING
This Gas Hob can be supplied in either of two Models
220 VOLTS 50 HZ or 1.5v D.C. Battery pack
.
IMPO R T AN T:
ANY SERVICING TO THIS APPLIANCE MUST BE CARRIED
OUT BY AN AUTHORIZED PERSON
.
SAFETY WARNING WHEN OPERATING WITH LP
GAS:
WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS, IT SHALL
NOT BE USED AS A SPACE HE
A TER .
SPARE PARTS SERVICE CONTACT NUMBERS:
For spare part and technical support enquires please call
MANUFACTURER: A’VARD INDUSTRIES P/L.
ADDRESS: 58-60 Quantum Close, South Dandenong, Victoria 3175, Australia.
TEL: [phone]
WEBSITE: www.goldlinecorp.com.au
e-mail: [e-mail]
Check the data label affixed to your unit to ensure the correct model has been supplied.
Should you notice any of these symptoms,
- flame light back
- flame lift off from burner ports
- popping or minor explosions sound
- appreciable yellow tipping flame
- objectionable odour

SPECIFICATION TABLE
Model number
Items
Unit
GL301BZNG
GL301BZLPG
GL301BZNG-CAST
GL301BZLPG-CAST
GL302BZNG
GL302BZLPG
GL302BZNG-CAST
GL302BZLPG-CAST
GL2BZNG
GL2BZLPG
GL2BZNG-CAST
GL2BZLPG-CAST
GL2WZNG
GL2WZLPG
GL2WZNG-CAST
GL2WZLPG-CAST
GL3BZNG
GL3BZLPG
GL3BZNG-CAST
GL3BZLPG-CAST
GL3WZNG
GL3WZLPG
GL3WZNG-CAST
GL3WZLPG-CAST
GL603BZNG
GL603BZLPG
GL603BZNG-CAST
GL603BZLPG-CAST
GL603WZNG
GL603WZLPG
GL603WZNG-CAST
GL603WZLPG-CAST
GL4BZNG
GL4BZLPG
GL4BZNG-CAST
GL4BZLPG-CAST
GL4WZNG
GL4WZLPG
GL4WZNG-CAST
GL4WZLPG-CAST
GL4SSNG
GL4SSLPG
GL4SSNG-CAST
GL4SSLPG-CAST
GL704BZNG
GL704BZLPG
GL704BZNG-CAST
GL704BZLPG-CAST
GL704WZNG
GL704WZLPG
GL704WZNG-CAST
GL704WZLPG-CAST
Ignition
-
-
DC 1.5V 220V/240V
Battery 50Hz
DC 1.5V 220V/240V
Battery 50Hz
DC 1.5V 220V/240V
Battery 50Hz
DC 1.5V 220V/240V
Battery 50Hz
DC 1.5V 220V/240V
Battery 50Hz
DC 1.5V 220V/240V
Battery 50Hz
DC 1.5V 220V/240V
Battery 50Hz
Type Reference
D/A
D
D
D
D
D
D
D
Top plate material
-
8mm toughened
Australian Glass
8mm toughened
Australian Glass
8mm toughened
Australian Glass
8mm toughened
Australian Glass
8mm toughened
Australian Glass
8mm toughened glass
or Stainless steel .
8mm toughened
Australian Glass
Glass Colour
-
Black/White
Black/White
Black/White
Black/White
Black/White
Black , White or Stainless steel
Black/White
Glass Shape
-
Rectangular
Rectangular
Curved
Curved
Rectagular
Rectagular
Rectagular
Nos. of hob
-
1
2
2
3
3
4
4
Gas Type
-
NG LPG
NG LPG
HKTown Gas
HKTown Gas
HKTown Gas
NG LPG
NG LPG
Heat input for burner
kW Left
(Mj/hr) Centre
Right
-
4.2 (15.0)
-
2.3 (8.0)
-
4.2 (15.0)
5.2 (18.72)
-
5.2 (18.72)
5.2 (18.72)
2.7 (9.72)
5.2 (18.72)
2.5 (9.0) x 2
-
5.2 (18.72)
2.5 (9.0) x 2
-
5.2 (18.72) x 2
2.5 (9.0) x 2
1.7 x1
5.2 (18.72) x 1
Flame failure device
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Gas pressure
kPa
1
1
1
1
1
1
1
Gas inlet connection
-
Screw-1/2 inch BSP
Screw-1/2 inch BSP
Screw-1/2 inch BSP
Screw-1/2 inch BSP
Screw-1/2 inch BSP
Screw-1/2 inch BSP
Screw-1/2 inch BSP
Tray depth
mm
43
43
51
51
40
40
40
Side clearance from the periphery of
each burner to any combustable surfa ce
mm
150
150
150
150
150
150
150
Clearance from base tray of cooker to
its non-combustable material underneath
mm
50
50
50
50
50
50
50
Dimension
Base tray (Bottom manifold Entry)
WxD mm
260 x 480
260 x 480
660 x 340
810 x 400
550 x 470
880 x 400
596 x 468
Base tray (Rear manifold Entry)
WxD mm
260 x 460
260 x 460
Glass top
WxDxH mm
300 x 500 x 8
300 x 500 x 8
750 x 450 x 8
860 x 460 x 8
640 x 500 x 8
930 x 450 x 8
640 x 500 x 8
Cut-out
WxD mm
265 x 485
405 x 485
665 x 345
815 x 405
555 x 475
885 x 405
601 x 473
Net weight
kg
9.5
11.5
13
16.5
13.8
18
18
Design and specification may change due to product improvement. No prior notice will be given. If there are any queries, please feel free to contact our service center.