Kuppersberg FT6VS16 Installation and maintenance instructions

TECHNICAL PASSPORT
ПАСПОРТ ТЕХНИЧЕСКОГО ИЗДЕЛИЯ
FT6VS16, FT6VS09
ELECTRIC HOBS
ЭЛЕКТРИЧЕСКИЕ ВАРОЧНЫЕ ПОВЕРХНОСТИ

2
TECHNICAL PASSPORT ENGLISH
Electric Hob
1. APPEAL TO CUSTOMER .................................................................................................... 3
2. IMPORTANT SAFETY INSTRUCTIONS...................................................................... 3
3. MAINTENANCE AND INSTALLATION MANUAL.................................................. 4
3.1. INSTALLATION INSTRUCTION .......................................................................... 4
3.2. ELECTRICAL CONNECTION.................................................................................. 4
4. CONTROLLER TYPE AND USE....................................................................................... 6
4.1. CONTROL PANEL........................................................................................................ 6
4.2. BASIC FUNCTION....................................................................................................... 8
5. MAINTENANCE AND CLEANING.................................................................................. 9
6. TROUBLESHOOTING –PROBLEM SOLVING......................................................... 10
CONTENTS

3
ENGLISH TECHNICAL PASSPORT
Electric Hob
1. APPEAL TO CUSTOMER
Carefully read the contents of this
lea et since it provides important
instructions regarding safety of
installation, use and maintenance. Keep
the lea et for possible future
consultation.
All the operations relating to
installation/replacement (electrical
connections) must be carried out by
specialised personnel in conformity
with the regulations in force.
2. IMPORTANT SAFETY
INSTRUCTIONS
It is recommended to use  at-
bottom pans with a diameter equal to
or slightly larger than that of the heated
area. Do not use pans with a rough base
to prevent scratching the heat surface
of the cooktop (Fig.2).
This appliance is not suitable for
use by children or persons requiring
supervision. Do not let children play
with the ap- pliance.
Before connecting the appliance to
the electricity supply:
ÂCheck that the voltage and
power values listed on the data plate
(positioned on the lower part of the
appliance) are com- patible with the
electricity supply and socket. If you have
any doubts, please consult a quali ed
electrician for assistance.
Important
 Avoid spilling liquid, therefore to
boil or heat liquids, reduce the heat.
 Do not leave the heating
elements on with empty pots and pans
or without receptacles.
 When you have  nished cooking,
switch off the relevant heating element
with the control indicated below.
Attention:
 Steam cleaners must not be
used.
ÂIf the surface is cracked, switch
off the appliance to prevent electric
shock.
 This appliance is not intended
for use by young children or in rm
persons without supervision
 Young children should be
supervised to ensure they do not play
with the appliance
This appliance conforms to the
European Directive EC/2002/96, Waste
Electrical and Electronic Equipment
(WEEE). By making sure that this
appliance is disposed of in a suitable
manner, the user is helping to prevent
potential damage to the environment
or to public health.
The symbol on the product
or on the accompanying pa- perwork
indicates that the appliance should not
be treated as domestic waste,
but should be delivered to a suitable
electric and electronic appliance
recycling collection point. Follow lo- cal
guidelines when disposing of waste. For

4
TECHNICAL PASSPORT ENGLISH
Electric Hob
FIG. 3
more information on the treatment, re-
use and recycling of this product, please
contact your local authority, domestic
waste collection service or the shop
where the appliance was purchased.
3. MAINTENANCE AND
INSTALLATION MANUAL
3.1 INSTALLATION
INSTRUCTION
These instructions address
specialised installers and serve as a
guide for installation, adjustment and
maintenance in conformity with the
laws and regulations in force.
If a built-in oven or any other
appliance that generates heat must be
 tted directly under the glass-ceramic
cooktop, THIS APPLIANCE (oven) AND
THE GLASS-CERAMIC COOKTOP MUST
BE SUITABLY INSULATED in such a
way that the heat generated by the
oven, measured on the bottom right
of the cooktop, does not exceed 60°C.
Failure to respect this precaution may
determine improper functioning of the
TOUCHCONTROL system.
The domestic appliance is designed
to be built into a worktop as illustrated
in the speci c  gure. Apply sealant
around the entire perimeter (cut-out
dimensions Fig.1). Fix the domestic
appliance on the worktop by means
of the 4 brackets provided, taking the
thickness of the worktop into account
(Fig.3). If the lower part of the appliance,
after instal- lation, is accessible via the
lower part of the cabinet then it is
necessary to mount a separator panel
Positioning (Fig.1)
respecting the distances indicated. If
the appliance is installed with an oven
underneath then the separator is not
necessary.
3.2 ELECTRICAL CONNECTION
Before making the electrical
connections, check that:
Âthe ground cable is 2 cm longer
than the other cables;
Âthe system ratings meet the
ratings indicated on the identi cation
plate  xed on the lower part of the
worktop;
Âthe system is  tted with ef cient
earthing compliant to the laws and
regulations in force.
ÂEarthing is obligatory by law.
FT6VS09,
FT6VS16

5
ENGLISH TECHNICAL PASSPORT
Electric Hob
Electrical connections :
ÂIf the appliance is not  tted with a cable, use type: “H05V2V2-F” for a power
level of up to 6400 Watts. The cross-section of the cable should be at least 2.5 mm2,
or 4 mm2 for greater power levels.
ÂThe cable should never reach a temperature which is 50°C above the
temperature of the room in which it is installed. The appliance is designed for
permanent connection to the electricity supply and should therefore be  tted with
an omnipolar switch which has a minimum opening of 3 mm between contacts. The
switch should be suitable for the charge indicated on the appliance data plate and
must conform to all current legislation (the yellow/green earth wire must not be
interrupted by the switch).
ÂThe omnipolar switch must be easy to reach once the installation process
has been completed.

6
TECHNICAL PASSPORT ENGLISH
Electric Hob
4. CONTROLLER TYPE AND USE
Use:
Use the touch control system in the corresponding position relative to the
individual cooking needs. Keep in mind that the higher the number, the more heat
that it is produced.
4.1. CONTROL PANEL
 A = ON/OFF button
B = Lock button
C = + button
D = - button
E = ON/OFF indicator
light lock button
F = Cooking zone
selector button
G = Double cooking
zone ON/OFF
indicator light
I = Rapid heating
function (Heat up)
active
L = Double zone
selector button
P = Timer buttons (+ / -)
Q = Cooking zone
display
R = Timer Display
 g. 4
 g. 5
 g. 6

7
ENGLISH TECHNICAL PASSPORT
Electric Hob
Depending on the model purchased,
the rst time the hob is switched on its
safety setting may be activated, i.e. the
“Lock button indicator light” (E) will be
illuminated. To use the hob, press and
hold sensor E for 3 seconds, until the
indicator light switches off.
ÂThe appliance can be switched
on by selecting start-up sensor A. A
zero will appear on all displays for 10
seconds. If no command is made within
10 seconds, the hob will switch off
again.
ÂA hotplate can be switched on by
selecting the “+” or “-” sensor within 10
seconds. If sensor D is used the display
will show selection 9, while if sensor C
is used, the display will show selection
1.
ÂOnce this step is complete
the user may make temperature
adjustments using the “+” or “-” buttons.
ÂThe hotplate can be switched off
by selecting “0” using sensor D; after 3
seconds the cooking zone will switch
off.
ÂA hotplate can also be switched
off by selecting the “+” or “-” sensors
simultaneously.
ÂThe hob can be switched off by
selecting the main start-up sensor A. If
all the hotplates are set to “0” the hob
switches off after 10 seconds.
ÂIf the hob is tted with
extendable hotplates, the second zone
may be switched on after the user has
ensured that:
Âthe LED corresponding to lock
button B is switched off (if it is not,
deactivate it).
ÂPress button A to switch on the
hob.
ÂSelect the desired hotplate and
adjust the power level using the “+” and
“-” buttons.
ÂOnce the power has been
adjusted, select button L to activate the
double zone.
ÂTo deactivate the double zone,
simply press button L.
ÂIf an object has been placed on
top of the control panel, the hob will
automatically revert to OFF mode.
ÂWhen a hotplate is in the OFF
mode and the temperature of the glass
surface is greater than approximately
50°, there will be a light signal “H” on
the corresponding cooking zone display.
ÂFunction B locks hob operation
the moment it is selected. E.g.: if the
function is activated when two zones of
the hob are switched on, the programme
remains locked at that level, even if the
user attempts to switch on another
zone. The same thing happens if the
appliance is switched off and the lock
function is activated: the user will not
be able to switch the hob on. To activate
or deactivate it, hold a nger in front of
sensor B for approximately two seconds.
The function is active when indicator
light E is illuminated. Even when the
lock button is activated, button A will
continue to work.

8
TECHNICAL PASSPORT ENGLISH
Electric Hob
4.2. BASIC FUNCTION
Heat up (Rapid heating)
The Heat up function can be
used to set the cooking zone to its
maximum temperature for a specied
period of time, after which the
temperature will return to a lower
value selected previously.
To activate the Heat up function,
select the hotplate by pres- sing the +
button until setting 9 is displayed; if
the button is pressed again a decimal
point “•” or the letter “A” will appear
on the display (next to the digit 9) for
5 seconds. This means the Heat up
function is active.
The desired power level (between
1 and 8) should be selected within 5
seconds. If power level 9 is selected,
the function is disabled. To deactivate
the Heat up function, simply select
the + button and hold it down until
setting 9 is reached and the decimal
point disappears from the display.
When the “Heat up” function is active,
the previously selected temperature
level may be increased by pressing
the (+) button. Once the cooking zone
has reached the selected temperature,
the“Heat up” function is automatically
deactivated and the hob emits a BEEP.
The cooking zone will operate in a
constant manner, at the set power
level.
Timer
Depending on the model of the
hob, it may be equipped with a TIMER
function.
This function can be used to
set an amount of time (between
00 and 99 minutes) after which the
selected cooking zone will switch off
automatically.
Operation:
ÂSelect the + or - button
corresponding to function P; 00 will
appear on the timer display.
ÂUse the “+” and “-” buttons to set
the desired timer period.
ÂIf the + button is pressed for
more than 2 seconds, the desired time
values can be reached more quickly.
ÂSelect a cooking zone and set
the desired temperature level (between
1 and 9).
ÂOnce the programmed time has
elapsed, display P will emit a sound
signal and will begin to ash.
ÂThis signal can be deactivated by
touching the + and - buttons on timer
display P.
ÂIf you wish to stop the TIMER
function before the set time has elapsed,
press the + and - buttons simultaneously.

9
ENGLISH TECHNICAL PASSPORT
Electric Hob

Maintenance :
Remove any residues of food and drops of grease from the cooking surface using
the special scraper (Fig.7).
Clean the heated area as thoroughly as possible using SIDOL, STAHLFIX or
similar products and a cloth/paper, then rinse with water and dry with a clean cloth.
Using the special scraper immediately remove any fragments of aluminium and
plastic material that have unin- tentionally melted on the heated cooking area or
residues of sugar or food with a high sugar content (Fig.7). In this way, any damage
to the cooktop surface is prevented.
Under no circumstances use abrasive sponges or irritating chemical detergents
such as oven sprays or stain removers.
FIG. 7

10
TECHNICAL PASSPORT ENGLISH
Electric Hob
–

Before you contact the Technical
Service, please perform the following
checks.
The appliance does not work:
Ensure that the power cable is
plugged in.
The pot sticks to the glass:
If there is molten material between
the pot and the glass, set the hot plate
to maximum power and try to separate
them.
Message U400 and acoustic
warning:
Power surge. Contact your
electricity company.
Continuous beep, control
disconnected and symbol
on display:
There is an object or liquid on the
touch control. Remove any object or
liquid on the touch control.
A hot plate disconnects and
message E2 appears on the display:
If during cooking the temperature
in the control electronics is excessive,
the hot plates near the control
might disconnect to avoid damages.
Excessive temperature problems
during cooking only occur in extreme
cases (cooking at maximum power for
a long time). In any case, leave the hot
plate to cool down for a few minutes.
If the problem persists, check that the
appliance was installed in accordance
with these manual instructions.