Goldline GLS2-923GSB1 User manual

Built -in Gas Hobs
Content
Safety instructions---------------------------------- 2
Product description--------------------------------- 3
Installation and User manual
Model numbers list :
NOT E : This User Instruction Manual contains important information, including safety
& installation points , which will enable you to get the most out of your appliance . Please
keep it in asafe place so that it is easily available for future reference ; for you or any
person not familiar with the operation of the appliance .
15
19
Issue Date :- 23/05/2017
Gas Conversion
21
Registering your Product

1
This manual explains the proper installation and use of your appliance, please read it carefully
before using even if you are familiar with the product. The manual should be kept in asafe
place for future reference. In case of failure, only the Authorized Technical Service may repair
this hob. Otherwise the guarantee will be null and void.
Warning
General safety
The appliance may only be installed and connected by trained, Authorised persons.
Built-in appliances may only be used after they have built in to suitable built-in units and work surfaces
that meet standards.
In the event of faults with the appliance or damage to the glass toughened (cracks, scratches or splits),
the appliance must be switched off and disconnected from the electrical supply, to prevent the possibility
of an electric shock.
Repairs to the appliance must only be carried out by trained Authorised persons.
The technical and identification data for the hob figure on the reference plate fixed to the appliance.
This reference plate must be consulted before making the electrical connections.
The electrical connections must be made by specialist aware to the legal and regulatory, requirements
in each country.
If the cable is damaged in any way it must be replaced by the manufacturer or after sale service or by
authorized technical staff, to avoid hazard.
Correct use
People (including children) who, because of their physical, sensory or mental capabilities or their
inexperience or ignorance are not able to use the device safely, should not use this device without supervision
or instruction by aresponsible person.
This appliance should be used only for normal domestic cooking and frying of food.
The appliance must not be used as a work surface or as a storage surface.
Additions or modifications to the appliance are not permitted.
Do not place or store flammable liquids, highly inflammable materials or fusible objects (e.g. plastic film,
plastic, aluminum) on or near the appliance.
Do not heat an empty pan on the appliance.
Children'ssafety
The cooking zones will become hot when you cook. Therefore, always keep small children away from the
appliance.
The appliance is not intended for use by young children or infirm persons without supervision.
Young children should be supervised to ensure that they do not play with the appliance.
Safety during use
Remove stickers and film from the glass ceramic.
There is the risk of burns from the appliance if used carelessly.
Cables from electrical appliances must not touch the hot surface of the appliance or hot cookware.
Overheated fats and oils can ignite very quickly. Warning! Fire hazard!
Switch the cooking zones off after each use.
Users with implanted pacemakers should keep their upper body at least 30 cm from cooking zones that
are switched on.
Risk of burns! Do not place objects made of metal, such as knives, forks, spoons and saucepan lids on
the cooking surface, as they can get hot.
Issue Date :- 23/05/2017

2
Safety Instructions and Product Description
Do not use or store flammable materials in the appliance storage drawer or near this appliance.
Do not spray aerosols in the vicinity of this appliance while it is in operation.
For Universal LPG appliance:- Where this appliance is installed in marine craft or caravans, it shall not
be used as aspace heater.
This hotplate must be installed in accordance with:
AS 5601 - Gas Installations ( for Australia)
NZS 5261 – Code of Practice for the Installation of Gas Burning Appliances and Equipment ( for New Zealand)
Local gas fitting regulations
AS/NZS 3000 – Electrical Installations ( Wiring Rules)
Building codes
Any other relevant statutory regulations.
Check the gas type label on the underside of the hotplate, adjacent to the gas connection to ensure it
corresponds to the installation gas supply. If in doubt contact the supply authority.
The power supply cord (supplied) must not touch against any hot surfaces and must be placed so that its
temperature does not exceed 75 degrees at any point along its length.
After connecting to gas, check for leaks using soapy solution, never a naked flame.
Where a flexible hose assembly is used, ensure it is approved to AS/NZS 1869, Class B or D.
Any hose assembly used must be restrained from accidental contact with the flue outlet of an under bench
oven. The hose is not to exceed 1.2m in length.
How to avoid damage to the appliance
The glass toughened can be damaged by objects falling onto it.
The edge of the glass ceramic can be damaged by being knocked by the cookware.
Cookware made of cast iron, cast aluminum or with damaged bottoms can scratch the glass toughened
if pushed across the surface.
Objects that melt and things that boil over can burn onto the glass ceramic and should be removed
straightaway.
Do not use the cooking zones with empty cookware or without cookware.
To avoid damaging cookware and glass ceramics, do not allow empty saucepans or frying pans to keep
heating by the hob.
The ventilation gap of 5mm between the worktop and front of the unit underneath it must not be covered.
Do not modify this appliance.
Safety when cleaning
For cleaning, the appliance must be switched off and cooled down.
For safety reasons, the cleaning of the appliance with steam jet or high pressure cleaning equipment is not
permitted.
Disposing of the device
When disposing of the device, do not bring it to regular municipal waste
containers. Instead, bring it to electrical and electronic waste recycling and
reuse center. A relevant label has been put on the device, its instructions
manual, or the package. The device has been manufactured of recyclable
material. By bringing old device to recycling collection center, you show that
you care about nature. Ask your local environmental care authority for
information on location of such facilities.
Tempered glass Trivet
Control knobs
SR
Wok Aux
SR
Model No .
Wok — Wok Burner
R— Rapid Burner
SR — SemiRapid Burner
Aux — Auxiliary Burner
Tempered glass Trivet
Control knobs
Wok
Model No .
Wok — Wok Burner
R— Rapid Burner
SR — SemiRapid Burner
Aux — Auxiliary Burner
Wok
Issue Date :- 23/05/2017Issue Date :- 23/05/2017

45
Tempered glass Trivet
Control knobs
Wok
R
Aux
Model No .
Wok — Wok Burner
R— Rapid Burner
SR — SemiRapid Burner
Aux — Auxiliary Burner
SR
SR
Model No .
Wok — Wok Burner
R— Rapid Burner
SR — SemiRapid Burner
Aux — Auxiliary Burner
Tempered glass Trivet
Control knobs
Wok R
Aux
SR
3
Tempered glass Trivet
Control knobs
Model No .
Wok — Wok Burner
R— Rapid Burner
SR — SemiRapid Burner
Aux — Auxiliary Burner
Wok
Aux
Wok
Tempered glass Trivet
Control knobs
Wok R
Aux
SR
Model No .
Wok — Wok Burner
R— Rapid Burner
SR — SemiRapid Burner
Aux — Auxiliary Burner
Issue Date :- 23/05/2017Issue Date :- 23/05/2017

Accessory Name Picture
( for reference only, physical unit maybe different)Quantity
User Manual
Installation clip
1
3
3
Screws ST4.2x18
Adhesive sealing tape
3
Natural gas regulator
Test point adapter
1
1
Seal ring A
Seal ring B
2
2
Connector A
Connector B
1
1
Technical
GLS5-912GSB1-C2
GLS4-919GSB2-C1
GLS4-919GSB2-C2
GLS2-923GSB1
GLS3-924GSB1
112x870x510 840 x480 220-240V/50Hz 2W
112x870x510 840 x480 220-240V/50Hz 2W
112x870x510 840 x480 220-240V/50Hz 2W
112x870x510 840 x480 220-240V/50Hz 2W
112x870x510 840 x480 220-240V/50Hz 2W
22 Kgs
16.2Kgs
22.3Kgs
16.1Kgs
16.4Kgs
Model product
dimensions
(hxwxd) mm
Cut-out
Size
( wxd)mm App’xnet
weight Electrical
connection
Rated
input
power
GLS4-619GSB1-C2 112x590x510 555 x475 13.8Kgs 220-240V/50Hz 2W
Details of the methods of connection
Before installation :
Before cutting into any bench tops, ensure the minimum clearances to walls, adjacent
surfaces and overhead surfaces required by the relevant gas appliance installation code ( see
above) will comply. Dimensions are specified in millimeters ( mm)
Overhead cupboards and range hood = 650 mm.
Side and rear clearance = 200 mm to any burner edge.
Overhead exhaust/ceiling fan = 750 mm
Horizontal surfaces adjacent the hob = less than or equal to the hob height.
Ensure there is sufficient clearance to fit the regulator and/or flexible hose connection with
the hotplate in the installed position.
When you have installed the hob, make sure that
The GPO(general purpose outlet) must always be in an accessible position.
The supply connection point, test point and natural gas regulator adjustment screw (for
Natural gas installation) are accessible for testing and/or adjustment with the hotplate in the
installed position.
TO BE INSTALLED ONLY BY AN AUTHORIZED PERSON
Issue Date :- 23/05/2017Issue Date :- 23/05/2017
Installation

3. Fit burners and trivet.
Replace burners and ensure they are correctly repositioned over the ignitor ( S) and
\thermocouple ( T). The ignitor ( S) must be clean for trouble free sparking. Test burner ignition
and burner flame for correct operation, If burner is placed correctly it will not rotate on its
supports..
The DCC ( Wok) burner ( diagrams below) does not fit over the igniter or thermocouple but must
be placed on its supports.
4. Electrical connection.
Install a10 amp general purpose outlet ( GPO) in accordance with relevant electrical standards
and/or codes of practice applicable.
The power supply cord ( supplied) must not touch against any hot surfaces and must be placed
so that its temperature does not exceed 75℃at any point along its length.
After having installed the hotplate, the GPO must always be in an accessible position.
Wiring diagram for
1. Cupboard Cutting
Bench top thickness, 30– 40 mm ( 3– 4cm).
2. Place burner box
Apply the adhesive sealing tape to the underside lip of the burner box. Shown at Gopposite.
Place burner box into cutout hole and fit clamping brackets to clamp the hotplate to the bench.
Issue Date :- 23/05/2017Issue Date :- 23/05/2017

Inlet connection region for flexible hose
After connecting to gas, check for leaks using soapy solution, never anaked flame.
Fit the duplicate data plate ( supplied in separate bag) on asurface adjacent to the hotplate,
for example, the inside of the cupboard door so it is clearly visible for any service technician.
SETTING THE GAS PRESSURE :
Fit amanometer with a6mm rubber hose to the test point on the regulator ( for natural gas).
For all the models, light all burners on and adjust test point pressure to 1.00 kPa. Turn burners
off and on again and recheck the pressure is same as set previously or adjust as required.
TEST FOR CORRECT OPERATION :
After installation and test point setting, each burner ignition and operation must be tested
individually and with all burners operating. This testing must be done by the installer before
leaving.
ADJUSTING THE BURNER MINIMUM FLAME HEIGHT :
NOTE: This adjustment can only be performed by authorised service personnel.
The minimum burner flame is factory adjusted for the gas type stated on the gas type label
adjacent to the gas connection and should not require adjustment. Adjustment may be required
if the hotplate has been converted from Natural gas to Universal LPG or vice versa.
GAS CONVERSION INSTRUCTIONS:
The manufacturers servicing instructions detail how authorised personnel may convert the
hotplate from Natural gas to Universal LPG or from Universal LPG to Natural gas. Contact the
manufacturer or agent as required.
Wiring diagram for
5. Gas connection
Install in accordance with relevant gas standards and/or codes of practice applicable.
Connect the elbow fitting to the appliance gas manifold connection, and check that seals
between the elbow and manifold connection are in place and in good condition.
For Natural gas : connect the natural gas appliance regulator (pictured opposite) with integral
test point using approved gas thread tape or compound to the elbow fitting.
For Universal LPG : connect the Test point adapter (pictured opposite) with integral test point
using approved gas thread tape or compound to the elbow fitting.
Ensure the supply connection point, test point and natural gas regulator adjustment screw
(for Natural gas installation) are accessible for testing and/or adjustment with the hotplate in
the installed position.
Where aflexible hose assembly is used, ensure it is approved to AS/NZS 1869, Class Bor D
with max. length of 1.2m. Any hose assembly used must be restrained from accidental contact
with the flue outlet of an under bench oven. This hose assembly shall be suitable for connection
to afixed consumer piping outlet located as follows:
Hotplates at apoint 800 mm to 850 mm above the floor and in the region outside the width of
the appliance to adistance of 250 mm.
Natural gas regulator
Issue Date :- 23/05/2017Issue Date :- 23/05/2017

Model
GLS5-912GSB1-C2
Auxiliary
Semi rapid x2
Rapid
Wok
TOTAL NHGC
NATURAL GAS
Injector
Dia(mm)MJ/hTest point
kPa Injector
Dia(mm)MJ/hTest point
kPa
UNIVERSAL LPG
0.9
1.8+0.8
4.0
6.5
17.2
45
1.0
1.0
1.0
0.53
0.69
1.02+0.5
3.6
6.5
17.2
44.6
2.75
2.75
2.75
1.18
1.55 10.8
1.0
0.9 10.8
2.75
Model
GLS3-924GSB1
Auxiliary
Wok x2
TOTAL NHGC
NATURAL GAS
Injector
Dia(mm)MJ/hTest point
kPa Injector
Dia(mm)MJ/hTest point
kPa
UNIVERSAL LPG
0.9
1.8+0.8
4.0
17.2
38.4
1.0
1.00.53 1.02+0.5
3.6
17.2
38
2.75
2.75
Model
GLS2-923GSB1
Wok
TOTAL NHGC
NATURAL GAS
Injector
Dia(mm)MJ/hTest point
kPa Injector
Dia(mm)MJ/hTest point
kPa
UNIVERSAL LPG
1.8+0.8 17.2
34.4
1.02+0.5 17.2
34.4
1.0 2.75
Model
GLS4-619GSB1-C2
Auxiliary
Semi rapid x2
Wok
TOTAL NHGC
NATURAL GAS
Injector
Dia(mm)MJ/hTest point
kPa Injector
Dia(mm)MJ/hTest point
kPa
UNIVERSAL LPG
0.9
1.18
1.8+0.8
4.0
6.5
17.2
34.2
1.0
1.0
1.0
0.53
0.69
1.02+0.5
3.6
6.5
17.2
33.8
2.75
2.75
2.75
Model
GLS4-919GSB2-C1
GLS4-919GSB2-C2
Auxiliary
Semi rapid
Rapid
Wok
TOTAL NHGC
NATURAL GAS
Injector
Dia(mm)
MJ/hTest point
kPa Injector
Dia(mm)
MJ/hTest point
kPa
UNIVERSAL LPG
0.9
1.18
1.8+0.8
4.0
6.5
17.2
38.5
1.0
1.0
1.0
0.53
0.69
1.02+0.5
3.6
6.5
17.2
38.1
2.75
2.75
2.751.55 10.8 1.0 0.9 10.82.75
Description Explanation
Zone indicators These show which zone is under control.
Flame power Flame power of the zones, is the lowest and is
the highest.
The hotplates are fitted with mains powered electronic spark ignitors, so must be connected
to mains power supply ( i.e. nominal 220 - 240 Vac) to operate. If power is not available, the
hotplate will still work but the burners will have to be lit with amatch or similar.
Depressing the gas control knob of any burner will activate the spark ignition for all burners.
To light the burner, turn the gas control knob to the High Flame setting of the burner to be lit,
while at the same time depressing the gas control knob to activate the spark ignition.
Once the burner is alight continue to depress the gas control knob for 5– 10 seconds to allow
the flame safeguard to activate. If when you release the gas control knob, the burner flame
goes out the flame safeguard has not heated up enough so repeat the ignition procedure after
waiting 1minute for gas to disperse. If problems with burner lighting persist, refer to the
TROUBLESHOOTING section of these instructions.
If power is not available, light amatch or similar, then turn the gas control knob for the burner
to be lit, to the High Flame setting. Once again if problems with burner lighting persist, refer
to the TROUBLESHOOTING section of these instructions.
When burner lights, adjust desired flame height. On finishing, turn control knob to off position
marked with ablack DOT.
BURNER AND UTENSIL CHOICE
The maximum utensil ( pan) diameters in millimetres ( mm) for each burner are:
1. For Natural Gas hotplates
Auxiliary ( small) and Semi-Rapid ( medium) = 195 mm
Rapid ( large) = 230 mm
DCC ( wok) = 300 mm
2. For Universal LPG hotplates
Auxiliary ( small), Semi-Rapid ( medium) and Rapid ( large) = 195 mm
DCC ( wok) = 300 mm
Issue Date :- 23/05/2017Issue Date :- 23/05/2017
Start using your appliance

( ) ( mm) :
( ) = 80 mm
Semi-Rapid ( ) = mm
Rapid ( ) T( ) = 195 mm
to ,
.
:
, . , mat,
to .
a
.
.
a
.
it
.
. ( ,
.) .
TOUGHENED GLASS PANEL
( e. . ) to
.
. W.
a.
: to
.
TRIVETS (UTENSIL SUPPORTS)
a
- . .
a.
BURNERS
. .
( ) ( ).
W.
a.
a, , item to
( )
( S) ( T). ( S)
. T
.
( Wok) ( )
.
it .
Gas Conversion (ULPG - NG)
kit
,
.
The ULPG to NG conversion kit contains
T
- Jet φ0.9mm -Semi-Rapid Jet φ1.18mm
- Rapid Jet φ1.55mm -Wok Jetφ0.8mm(IN)+ φ1.8mm(OUT)
Issue Date :- 23/05/2017Issue Date :- 23/05/2017

Converting to
agas type
to
kit.
to 1.
.
Changing the jets
1. , .
2. ato
, kit.
.
3. kit to
.
Setting the minimum level
1. , .
2. , .
3. tap to
.
. ato -
.
T- .
a,
. , -
- .
5. tap
to .
6. Repeat .
. , .
8. , , ,
.
Gas Conversion (NG- ULPG)
kit
,
.
The NG to LPG conversion kit contains
-T T
φ0.53mm -Semi-Rapid Jet φ0.69mm
-Rapid Jet φ0.9mm -Wok Jetφ0.50mm(IN)+ φ1.02mm(OUT)
Converting to agas type
to
T
kit. a
2.
to 2. .
Changing the jets
1. , .
2. ato ,
kit.
.
3. kit to
.
Setting the minimum level
1. , .
2. , .
3. tap to .
. ato -
. T
- . a
,
. , - -
.
5. tap
to .
6. Repeat .
. , .
8. , , ,
.
Universal LPG
2.75kPa Model
Burners
Type
Semi
Rapid
Wok
(mm)
0.53
0.69
0.9
0.50+1.02
3. /
6. /
10. /
. /
TOT ( / )
0
1
2
0
38
2
1
0
1
33.8
0
0
0
2
.
Issue Date :- 23/05/2017Issue Date :- 23/05/2017

TROUBLESHOOTING
Servicing of the hotplates must only be done by an authorised service representative ( see
back of this booklet) and the hotplate must not be modified. Power must be disconnected
before any servicing or maintenance is conducted.
Abnormal conditions include:
Excessively yellow or sooting flame type.
Flame lifting off the burner ports.
Flame lighting back into the burner (normally associated with a popping sound).
Objectionable odour of the flames combustion products.
Should afaulty condition develop in the hotplate that is not described above, refer to the
following table first for possible causes and remedies prior to contacting an authorised service
representative. Servicing beyond the remedies listed shall only be undertaken by an authorised
service representative.
1
1
1
1
1
1
1
1
38.138.1
2
1
1
1
44.6
Universal LPG
2.75kPa Model
Burners
Type
Auxiliary
Semi rapid
Rapid
Wok
Injector
Dia(mm)
Nominal Gas
Consumption
0.53
0.69
0.9
0.50+1.02
3.6MJ/h
6.5MJ/h
10.8MJ/h
17.2MJ/h
TOTAL NHGC(MJ/h)
Model
Burners
Type
Injector
Dia(mm)
Nominal Gas
Consumption
TOTAL NHGC(MJ/h)
0
1
2
0
2
1
0
1
0
0
0
2
1
1
1
1
1
1
1
1
2
1
1
1
Model
Burners
Type
Injector
Dia(mm)
Nominal Gas
Consumption
TOTAL NHGC(MJ/h)
NATURAL GAS
1.0kPa
NATURAL GAS
1.0kPa
Auxiliary
Semi rapid
Rapid
Wok
0.90
1.18
1.55
0.8+1.8
4.0MJ/h
6.5MJ/h
10.8MJ/h
17.2MJ/h
Auxiliary
Semi rapid
Rapid
Wok
0.90
1.18
1.55
0.8+1.8
4.0MJ/h
6.5MJ/h
10.8MJ/h
17.2MJ/h
34.438.434.2
45 38.538.5
31
FAULT POSSIBLE CAUSE REMEDY
Check plugged in and switched on.
Check mains circuit breaker.
Call authorised representative.
Remove and re-fit burner.
No power.
Loose sparker cable.
Burner not aligned properly.
No spark when gas
control knob depressed.
Gas supply off.
Burner not aligned properly.
Burner ports blocked.
Check gas supply valve on.
Remove and re-fit burner.
Remove, clean and replace burner.
Burner not lighting when
spark ignition working.
Burner goes out when
control knob released.
Flame safeguard not activated.
Flame safeguard faulty
connection or broken.
Re-light, allow more time for flame
safeguard to activate.
Call authorised representative.
Uneven flame pattern
or slight flame lifting.
At minimum flame setting
the flame is too high.
Burner ports blocked.
Turndown control setting
incorrect.
Remove, clean and replace burner.
Call authorised representative.
Small flame on
High setting.
Regulator faulty.
Gas supply pressure low.
Incorrect injector fitted.
Blocked injector or gas supply tube.
Incorrect utensil size.
Call authorised representative.
Call authorised representative.
Call authorised representative.
Call authorised representative.
Refer to operating instructions
utensil choice.
Flame too high
on High setting.
Regulator faulty.
Incorrect injector fitted.
Incorrect utensil size.
Call authorised representative.
Call authorised representative.
Refer to operating instructions
utensil choice.
Issue Date :- 23/05/2017Issue Date :- 23/05/2017

1.1In this warranty:
1.1.1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition
and Consumer Act 2010;
1.1.3 Consumer means a “consumer” as that term is defined in Section 3 of the Australian
Consumer Law as the original purchaser of aGoldline product;
1.1.4 Consumer Guarantees means the guarantees under the Australian Consumer Law;
1.1.5 You means the Consumer.
1.2Nothing in this warranty affects any person’srights under the Australian Consumer Law.
The benefits to any Consumer under this warranty are in addition to the rights and remedies
available under any Consumer Guarantees.
1.3Subject to the other clauses of this warranty, the Company warrants to the Consumer that
the Goldline product will be free of manufacturing defects and will perform to the Company’s
specifications.
1.4The benefit of this warranty extends only to the Consumer as original purchaser of aGoldline
product which is installed in aresidential property.
1.5This warranty commences on the date of purchase of the Goldline product by the Consumer
and continues for the benefit only of the Consumer until the expiry of one ( 1) year (Warranty
Period ).
1.6If within the Warranty Period amanufacturing defect is discovered in the Goldline product or
it fails to perform to the Company’sspecifications as aresult of some defect in materials,
components or workmanship ( Defect) then the Company will, at its option, repair the Goldline
product or supply areplacement Goldline product free of charge. Areplacement Goldline product
may differ from the original product purchased by the Consumer.
1.7This warranty will not apply to any Goldline product:
1.7.1 Installed by any person other than a qualified tradesperson; or
1.7.2 Subjected to misuse, neglect, negligence or accidental damage; or
1.7.3 Operated in any way contrary to any operating or maintenance instructions; or
1.7.4 Improperly handled, installed or maintained; or
1.7.5 Altered or modified prior to or after installation; or
1.7.6 Damaged directly or indirectly by power surges, electrical storm damage or connection
to incorrect power supply
The Australian Consumer Law requires the inclusion of the following statement with this warranty:
Our goods come with guaranteed that cannot be excluded under the Australian Consumer
Law . You are entitled to areplacement or refund for amajor failure and for compensation
for any other reasonably foreseeable loss or damage .
You are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to amajor failure .
1.8You must provide proof of your purchase of the Goldline product and the date of purchase in
order to obtain the benefit of this warranty.
1.9If you live outside the service area of the Company or one of its service agents, this warranty
does not cover the cost of transport of the Goldline product for service nor the service agent’s
traveling costs to and from your home.
1.10 If you are required to transport the Goldline product to the Company or its service agent,
you must ensure it is safely disconnected by aqualified tradesman and securely packed and
insured. The Company does not accept any responsibility for loss or damage of the Goldline
product prior to it being received by the Company or its service agent.
1.11 You will be responsible for all costs of returning aGoldline product to the Company and for
redelivery of the Goldline product by the Company ( whether it is the original or arepaired and/or
areplacement Goldline product) and for any other expenses you incur in claiming under this
warranty.
1.12 The Company or its service agent will examine any Goldline product and if the Company
determines that it is defective through no fault of the Owner and is otherwise undamaged, the
Company will repair or replace the Goldline product in accordance with this warranty.
DO NOT SEND IN THIS WARRANTY
Fill out the following details and file with your purchase invoice.
RET AIN & FILE WITH YOUR RECEIPT
Your Purchase Receipt/Invoice is proof of date of purchase. If you are unable to establish the
date of purchase, or if the fault is not covered by this warranty, or if the product is found to be
in working order, you will be required to bear all service call charges.
Company name Goldline reserves the right to discontinue items, modify designs and change
specifications without incurring obligation.
Whilst every effort is made to ensure that descriptions, specifications and other information
in this publication is correct, no warranty is given in respect thereof and the company shall
not be liable for any errors therein.
Purchased
For Customer records.
from:
Co. Name:
Address:
Date of Purchase:
Serial number:
NOTE: Consistent with our continuing product development policy, improvements may have
been made which render the contents of this packaging slightly different to that shown.
Issue Date :- 23/05/2017Issue Date :- 23/05/2017
To Register your product, please visit Goldline website.
FOR WARRANTY SERVICE CALL GOLDLINE (AUSTRALIA) TO CONNECT YOU TO THE
NEARESTAUTHORISED SERVICE CENTRE
IN ORDER TO MAKE A CLAIM UNDER THIS WARRATY, THE CONSUMER MUST CALL
GOLDLINE - 03 9799 9660 (AUSTRALIA) TO CONNECT TO THE NEAREST AUTHORISED
CENTRE