Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE
11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
SkyTrak+ is charging
02 I
What's in the Box
SKYTRAI<
Skal<
+
contains a Lithium-polymer rechargeable battery
that can operate up to 5 hours on a full charge.
*
IMPORNT: Skak
+
must be charged for a minimum of
6 hours before use.
NOTE:
NOTE:
Powering On/Off
*
LED Locations
Description
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Battery is low and SkyTrak+ is about to turn
itself off. Please charge your SkyTrak+ as
soon as possible.
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
SkyTrak+ is in Direct Connect Mode, waiting
for a connection with the SKyTrak application.
Power WiFi Ready
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
SkyTrak+ is in Network Mode and it has
located a known Wi-Fi network. It is attempting
to connect to that network.
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
SkyTrak+ is searching for a Wi-Fi Network
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
SkyTrak+ is connected to Wi-Fi and the SkyTrak
application, but is not armed for a shot to be hit.
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
You are cleared to hit a shot on your SkyTrak+
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
SkyTrak+ is capturing the shot that was just hit
Power
LED
Wi-Fi
LED
Ready
LED Description
Battery is low and SkyTrak+ is about to turn itself
off. Please charge your SkyTrak+ as soon as
possible.
SkyTrak+ is in Direct Connect Mode, waiting for
a connection with the SkyTrak Application on
your tablet.
SkyTrak+ is in Network Mode and it is attempting
to locate and connect to a known Wi-Fi network.
SkyTrak+ is in Network Mode and it has located
a known Wi-Fi network. It is attempting to
connect to that network.
SkyTrak+ is in Network Mode and it is connected
to a known network. It is waiting for a connection
with the software on your tablet.
SkyTrak+ is connected to the Application. If the
Ready LED is not turning green quickly, please
check to see if SkyTrak+ is tilted instead of
being level.
SkyTrak+ is ready for your next shot.
SkyTrak+ is charging.
SkyTrak+ is charging, but the power of the
charger is not adequate, it may take a long time
for your SkyTrak+ to charge.
Use this chart to identify or troubleshoot SkyTrak’s various operational modes.
Problem Solution
When charging, ‘Power’
LED does not come on
(AMBER)
Press and hold the Power button for 5 seconds. Make
sure the USB cable has power. Try other ports on your
computer or use a compatible USB wall charger.
SkyTrak+ should be turned OFF to charge.
All 3 LED’s turn red and unit
turns off after 15 seconds
Battery is low. Connect the USB cable and charge the unit.
The Power LED will turn off when SkyTrak+ is fully
charged and ready to go.
‘Wi-Fi’ LED is not turning
green
First, ensure that your SkyTrak+ is connected to the
Wi-Fi network. Then start the SkyTrak software on
your iPad and allow it to load. When the application is
open, SkyTrak’s LEDs will show whether it successfully
connected.
Wi-Fi and Power LEDs are
green, but ‘Ready’ (top)
LED is red
Your SkyTrak+ may have been triggered by a waggle
or other club movement. If you’ll wait a few seconds, it
should turn green again. If it still doesn’t turn green, you
should check your Wi-Fi connection and restart the
application on your iPad.
Results seem inaccurate Be sure to position the ball correctly on the red dot and
make sure the unit sits level with the hitting surface. If
using a tee, make sure the base of the tee is on the red
dot.
Troubleshooting
LED Color Code Chart
10 SKYTRAK+ QUICK START GUIDE 11
WWW.SKYTRAKGOLF.COM
Should this Trouble Shooting Guide not answer your question, please refer to
our Support Center at support.skytrakgolf.com, or you can contact
Customer Support at 1-833-SKYTRAK
