Goodlife HOU714 User manual

A1
A2
BCD E F G
4PCS
4PCS 3PCS 2+1PCS 41+1PCS 20+2PCS 12PCS 12PCS
Power Tool Organizer
HOU714

12
14
13
21
22
15
15
1
17
4
20
20
2
6
19
18
8
16
17
3
18
20
20
2
5
7
9
10
11
21

STEP1 STEP2
STEP4
STEP3
D*5
6*D2*D
7
5
6
D
6
16
9
5
7
D
7
6
5
10
Insert veritcal supports #5 and #6 into part #7, please
note that there are holes in the lower part of #5 and
#6, please face outward.
Insert part #16 into slots of part #5&6,
and attach #9 to part #7 with hardware D.
Use Hardware D to attach part #10
to Parts #5,6,&7. Please be careful
not to install #10 backwards,with the
larger hole facing outwards.
Attach part #8 to parts #,5,6, & 9 using hard-
ware D; please pay attention to the front &
back, with the larger hole facing upwards.
D
D
D
7
5
8
6
9

STEP5 STEP6
STEP8
STEP7
8*D
C*2
15
8
5
7
9
6
12
1
6
8
5
7
9
D
D
111
12
17
13
6
10
7
17
A1 B
A2
OPEN
Open part #15 and insert between
parts #5 and #6 down to part #8.
Install #14 behind #15, insert a dowel (hard-
ware C) on both sides then attach parts #12 &
#13 on each side using same dowels, please
be careful not to install #12 #13 #14 backwards.
Attach part #1, to parts #5,6,12,13, and 14
using hardware D. Tighten all screws (D).
Slide parts #17 x2 between parts #1 & #7. Then
attach part #11 to part #1. First tighten the screws
A1 (x4), then insert dowels B (x3) , then release
#11, and insert & tighten A2 connector nuts.
C
6
13
5
14
15
15
16
12
7
10
3*B4*A

STEP9 STEP10
STEP11
D*8
D*12
1
5
3
18
8
9
7
6
10
4
18
8
1
11
4
6
5
7
3
9
D
D
1
4
6
7
9
8
5
3
2
2
D
D
21
22
21
F
G
STEP12
GF
Attach side parts #3 and #4 using hardware D (x12)
, please pay attention to the hole position inward.
Choose a suitable height to hang. Read & see step 13 diagram
first to understand position of mounting plates relative to the top
of the unit. Mark and Drill Holes as shown. Install #22 mounting
plate to wall using hardware G (drywall anchors) & F (screws) .
After attaching, leave 2 inches on the left and right, then attach
the mounting plate accessories #21 (x2) in same manner.
Install both parts #2, each with four
hardware D. Tighten screws D (x8).
Insert two pieces #18 as shown.
F*12 G*12

STEP13
STEP14
F*4 G*4
E*20
STEP15
13
14
22
21
12
21
11
1
4
6
8
9
5
37
2
2 10
11
1
64
20
20
19
2
20
8
5
3
7
2
20
F
F
G
G
E
Now you can hang the tool cabinet on the wall.
Parts #12,13,and 14 will sit on back mounting
plates (parts#21 & 22). Use an electric drill or a
pen to mark the four holes of #10
Then punch and install the expansion screws G
and F, attaching unit to wall.
Attach shelves #19 and #20 (x4) using hardware
E (x20) in predrilled holes at desired height.
Finish Installation