Gorenje GDV641XL User manual

User manual
Bedienungsanleitung
Uporabniški priročnik
Uživatelská příručka
Руководство пользователя
Посібник користувача
article nuber
GDV641XL

2
Contents
Read the directions of use
Read the directions of use before starting to
use your machine, especially the Safety, Child
Safety and Basic Course sections.
Take care with certain materials
Read the section ‘Fragile dishes’ before
washing china with unglazed decoration or
other household goods made of plastic, wood
or crystal requiring careful treatment.

EN
Page
 
Safety 3
Child safety 3
Parts of the dishwasher 4
Baskets 4
Control panel 6
Dispenser 6
Basic Course 7
Eco-dishwashing 9
Fragile dishes 10
Status light 10
Rinse aid 11
Salt 11
Page
  
Cleaning 13
Settings 15
Fault indications 17
Troubleshooting 17
Performance information 19
  
   
  
   

3
Safety / Child safety
General
• Read and keep the directions for use!
• Installation of water, drainage and electricity must be
carried out by a qualied professional.
• Do not use the dishwasher for any purposes other than
those stated in this User Guide.
• Do not load the dishwasher with anything other than
dishes.
• Only use dishwasher detergent!
• Never leave the dishwasher door open as someone
may trip on it.
• Place knives and other sharp objects so that they
cannot cause injury to people or damage the
dishwasher.
• The appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that they do
not play with the appliance.
• Damaged mains cables must only be replaced by a
qualied electrician.
• This appliance is intended to be used in household and
similar applications such as:
- sta kitchen areas in shops, oces and other working
environments
- farm houses
- by clients in hotels, motels and other residential type
environments
- bed and breakfast type environments
Never put dishes containing solvent residue in the
machine due to risk of explosion. Neither may dishes
containing ashes, wax or lubricating grease be washed
in the dishwasher.
Winter storage/Transport
Store the machine away from frost.
Avoid long journeys in extreme cold. Transport the
machine in an upright position or lying on its back.

The overll protector starts pumping out water and
closes o the water intake if the machine’s water level
exceeds the normal level. If the overll protector starts
up, shut o the water supply and phone for service. See
‘Troubleshooting’.
Cleaning
Only use a slightly damp cloth for cleaning around the
edge of the door. Do not use a spray bottle! Water can
penetrate into the lock and come into contact with the
electrical components.
Packaging materials
Sort at source in accordance with the recommendations
of your local authority.
Scrapping
When the time comes for the machine to be scrapped, it
should immediately be rendered unusable. Remove the
plug and cut o the lead as short as possible.
Contact your refuse collection department or your local
authority for information on the correct way to dispose of
the machine!
The machine is manufactured and labelled for recycling.
Child-safe button lock
To prevent children starting the machine, you can
activate a button lock.
Proceed as follows:
1. Switch o the dishwasher with the main switch.
2. Hold in the Temperature and Drying buttons for 3
seconds, and at the same time switch on the main
switch.
The Temperature, Drying and start symbols will then
ash. Release the Temperature and Drying buttons.
3. Press the Program selection button. Once the symbol
for Auto wash lights up, the button lock has been
activated.
4. Press the Start/Stop button to store the setting.
Once the button lock has been activated, the
Temperature and Drying symbols will ash when any
of the buttons are pressed.
To deactivate the button lock temporarily when you
want to start the machine, press the Temperature and
Dry buttons simultaneously. The button lock will then
automatically switch on again after 3 minutes.
To deactivate the button lock altogether, use the same
procedure as for activation. When the symbol for Auto
wash goes out, the button lock has been deactivated.
Advice!
You can read more about this in the Settings chapter.
Child-safe dishwashing
• Use the knife basket, or knife holder, for all long/sharp
items.
• Always close the door and start the program
immediately once dishwasher detergent has been
added.
• Keep children away from the dishwasher when it is
open. There might be remains of dishwasher detergent
present!
• Do not allow children to use or play with the dishwasher.
Always take particular care when the door is open.
- Dishwasher detergent is corrosive!
Store dishwasher detergent and rinse aid out of the
reach of children! Should dishwasher detergent be
swallowed, immediately drink one or two glasses of milk
or water. Do not attempt to induce vomiting. Contact a
doctor! Should dishwasher detergent come into contact
with the eyes, rinse (for at least 15 minutes) with copious
amounts of water.
Protect your children!

4
Parts of the dishwasher* / Baskets*
1. Upper basket
2. Spray arms
3. Cutlery basket
4. Lower basket
5. Rinse aid dispenser
6. Dishwasher detergent compartment
7. Main switch
8. Program panel
9. Filter
10.Type plate
2
3
4
5
6
7
8
1
9
10
2
Upper basket
1
2
1. Wine glass shelf
2. Knife stop
Lower basket
2
3
2
1
*Details may dier depending on the model and market!
Baskets*
*Details may dier depending on the model
and market!
2
1. Fold-down plate support
2. Forward mount for plate support (used
for plates with a Ø greater than 25 cm)
3. Handle

5
Cutlery basket
1a 1b 1c
Cutlery basket with cover
2b
2a
2c
Placement of the cutlery basket cover (in Upper basket)
3a
3b
*Details may dier depending on the model and market!

6
Control panel / Dispenser
1. Program selector
2. Auto wash
3. Heavy wash
4. Normal wash
5. Delicate wash
6. Quick wash
7. Rinse & Hold
8. Higher temperature
9. Delayed start
10.Extra dry
11.Rinse aid indicator
12.Salt indicator
13.Start/Stop
65 8 9
12 3 4 7 10 1311
12
P
1 3
4
5
2
1. Compartment for main wash
dishwasher detergent
2. Compartment for pre-wash detergent
3. Rell indicator rinse aid (not all
models)
4. Rinse aid cover
5. Detergent compartment cover
Dispenser

7
Basic Course
Below are step by step instructions to help you achieve
the best possible dishwashing results.
Load the baskets correctly
Do not rinse dishes under running water before loading
them in the dishwasher. Simply scrape o large food
particles before loading the dishwasher. Convenient and
environmentally friendly!
Place glasses, cups, bowls, side plates and saucers in
the upper basket, wine glasses should be placed on the
wine glass shelf, and knives in the knife stand if present.
NOTE!
Ensure that all soiled surfaces face inwards or
downwards!
Place dinner plates, side plates, serving dishes,
saucepans and cutlery (in the cutlery basket) in the lower
basket.
Stand the cutlery with handles downward and as spread
out as possible. Ensure that spoons are not resting inside
each other.
Do not put cutlery made of dierent materials, e.g. silver
and stainless steel, in the same compartment (risk of
stains).
WARNING!
Knives and other utensils with sharp points must be
loaded in the basket with their points down or placed in a
horizontal position.
See Fragile dishes, if you want to wash articles that may
be fragile.
Check that the spray arms are able to
move freely.
Detergent dosage
Detergent should be dispensed in accordance with the
water’s hardness level.
Follow the dosage instructions on the detergent
package. If your dishwasher is tted with a water
softener, dispense as for soft water.
Pour the dishwasher detergent into the dishwasher
detergent compartment. There is one compartment for
pre-wash and one for main wash, see Dispenser. Phone
the dishwasher detergent manufacturer if you have any
questions regarding the detergen
WARNING!
Children must be supervised – dishwasher detergent is
corrosive!
NOTE!
Use only dishwasher detergent! Washing up liquid
must not be used as the foam that forms prevents the
dishwasher from operating eectively.
Dishwasher tablets
Halve the tablet if it is dicult to close the dispenser
cover.
NOTE!
Dishwasher tablets are not recommended for short
programmes (less than 75 minutes). Use powder or
liquid dishwasher detergent instead.
3in1/ Combined detergent
Read through the directions for these products
carefully. If anything is unclear, contact the
detergent manufacturer.
Press the main power switch
Select program
Select a program by pressing the program selector one
or more times until the required program is displayed.
Auto wash
The dishwasher can measure how dirty the dishes
are and adjust water consumption and temperature
accordingly. When newly installed, the programme needs
to be run ve times before it is fully adapted and can
provide the best results.
Heavy wash
Programme for very dirty dishes, such as pans,
casserole dishes and oven dishes. If these dishes do not
completely ll the dishwasher, you can add plates and
the like.

8
Basic Course
Rinse & Hold
For rinsing the dishes while waiting for the machine to
be lld.
If you wish to use additional options,
continue to point 6. Otherwise you can now
start the machine, see point 7.
Select options
To select an option, press one of the option uttons.
Temperature
With the temperature option button you can select the
wash temperature.
Program Normal °C Eco °C
Heavy wash: 70 55
Normal wash: 65 55
Delicate wash: 50 40
Quick wash: 60 30
The temperature symbol will light up if you have chosen
the normal temperature. This selection will remain in
force until a chnge is made.
Delayed start
If you want the machine to start later, press the Delayed
start option button. The clock symbol on the button lights
up. Then press the Start/Stop button and the machine
will start the program 5 hours later. To cancel delayed
start, hold down the Start/Stop button for tree seconds.
Drying
If you require a better drying result, press the option button
Drying to select normal drying. A symbol in the form of
three wavy lines lights. If you want a program with Eco
drying – press it again and the symbol will go out. The fan
assists drying even if Eco dry is selected, but not in the
Quick Wash program.
7
Press Start/Stop
The dishwasher will now start. It manages the entire wash
automatically. Ensure that the door is properly closed or the
machine will not start.
Changing options
If you want to change program after having started the
machine, press the Start/Stop button for three seconds.
Then select a new program and then press the Start/Stop
button again.
Do you want to load more dishes?
Carefully open the door; the machine will stops
automatically, put in the dishes, close the door and the
dishwasher will continue from where it left o.

switch
(or in the event of a power cut) before the washing program
has been completed, the interrupted program will continue
when power comes back on.
NOTE!
If the power is switched o, or if the door is open for more
than 2 minutes during drying, the program isinterrupted.
After dishwashing
Once the machine has nished, it only draws standby
current. Turn o the water faucet if the machine is not to be
used for an extended period, such as during vacations, for
example.
Drying
For additional drying the door should be opened 35 mm
upon completion of the drying cycle.
Normal wash
Use to wash normally dirty dishes, and even dishes with
dried leftovers, such as plates, serving dishes, cups,
glasses and so on.
Delicate wash
If the dishes are not heavily soiled, you can select
Delicate wash. This program is intended for glass and
china which has just been used and therefore does not
need such a powerful program.
Quick wash
This programme is used for glasses and porcelain that is
slightly dirty, such as coee cups.

9
Eco-dishwashing
Only wash with a full load
Waiting to run the wash until the machine is full saves
energy.
Wash at a lower temperature
If the load is only lightly soiled, you can lower the
temperature.
Select program with Eco drying
To save energy, select Economy dry. You will get a better
drying result if you leave the door slightly open after the
end of the program.
Do not rinse before dishwashing
You do not need to rinse the dishes before loading them
into the machine. Just scrape o large food particles
before loading the machine.
Choose environmentally-friendly dishwasher
detergent
Read environmental declarations on the package!
Connect to cold water...
if you use oil or electricity to heat your home.
Connect to hot water (max. 70 °C)...
If you use, for example, district heating, solar power or
geothermal power to heat your home.
Choosing a hot water connection cuts programme times
and reduces the dishwasher’s electricity consumption.

10
Fragile Dishes / Status light
The status light at the bottom on the dishwasher
provides information by means of 3 dierent colours.
Adjust the status light so that it is seen clearly by pulling
out or pushing in the transparent plastic strip.
Blue
Load more. The programme has started, but you can still
load more dishes.
Red
Do not load. You should not load more dishes (risk of
poorer dishwashing result).
Flashing Red
This indicates a fault. See further in the sections Fault
indications and Troubleshooting.
Green
Unload. The dishwashing programme is nished.
Standby light for two hours.
Wood
Wooden articles should only be machine washed if they
are labelled as dishwasher proof.
Aluminium
Aluminium can be dulled by machine washing.
However, good quality aluminium saucepans
can be machine washed, although a reduction in
lustre should be expected.
Plastic
Certain types of plastic cannot withstand
the high temperature generated in machine
dishwashing.
To protect plastic articles
Select a program with Economy temperature
and Economy drying.
Status light
Status light
A number of household goods are not suitable for
machine washing. There can be many reasons for this.
Certain materials cannot withstand intense heat, others
can be damaged by the dishwasher detergent.
Fragile decoration
China with decoration on top of the glaze (the article has
a rough feel) should not be machine washed.
Crystal/ glass
Place the articles so that they do not knock together
during the wash. Use the lowest possible wash
temperature and the shortest possible program. Do not
heat dry! Antique and very fragile items should not be
machine washed.
Glass which is machine washed at high temperatures
can in time develop a grey lm which cannot be removed.
Wash ne glass at the lowest temperature and with a low
dosage of dishwasher detergent.
Silver
Silver and stainless items should not come into contact
with each other as the silver can discolour.
Cutlery with glued handles
Certain types of adhesive cannot withstand machine
washing. In such cases the handles can come loose.

11
Rinse aid / Salt
Pour in rinse aid
Rinse aid, helps quicken the drying process.
Machines with indicator on the panel
When the rinse aid has run out and more is needed, the
rinse aid symbol on the panel lights up*.
To ll with rinse aid:
Turn and lift up the cover of the rinse aid compartment
to the right of the dispenser. This is where you top up
and set the amount of rinse aid to be dispensed in each
wash.
Carefully pour in rinse aid up to the knob for dosage
setting.
Alter dosage if required. Do not forget to close the cover.
*NOTE!
After lling there may be a short delay before the signal
light goes out.

There is a rell indicator in the middle of the dispenser
(see picture). If the rell indicator is totally black, there is
sucient rinse aid. However, if the indicator has a more
transparent appearance, you need to top up with rinse
aid (see above).
Select dosage
The dispenser is usually set at 1= soft water. However,
depending on the water hardness, it may be necessary
to change the dosage.
Open the rinse aid cover. Here you will nd the
dispenser’s adjustment dial. Settings 1-6: the harder the
water, the higher the dosage.
When the water hardness exceeds 10-12 °dH you
should use rinse aid with citric acid (acid rinse aid) if
the machine does not have a water softening lter. If the
machine has a water softening lter, dispense as for soft
water.
Too much rinse aid can lead to the build-up of foam. If
your water is particularly soft, you can dilute the rinse aid
(1 part rinse aid, 1 part water).
Too much rinse aid can cause streaks on the dishes,
while too little can result in water stains.
Add salt
Before using a dishwasher with a water softening lter,
you must ll the salt compartment with salt. Use coarse
salt or special salt for dishwashers.
It is best to ll with salt when you are about to do a wash,
as the dishwasher needs to be rinsed out immediately
after lling.
Proceed as follows the rst time:
1. First unscrew the cover as illustrated.
2. Place the funnel, which is supplied with the
dishwasher, into the compartment’s ller hole.
3. First pour in approximately 1 litre of water. Then ll the
compartment with max 1.5 kg salt.
4. Wipe away excess salt so that the cover can be
properly screwed into place.
5. Run a Normal wash program so that any salt in the
machine is rinsed away.
When the salt runs out, the salt symbol on the display*
lights up. Unscrew the cover and ll the compartment
with salt. Water is only needed on the rst occasion!
Wipe clean and screw back in place. Run a Normal wash
program so that any salt is rinsed away.
*NOTE!
After lling, there may be a short delay before the signal
light goes out.
WARNING!
Never pour dishwasher detergent into the salt compartment.
It will destroy the water softener!
Cover for the salt compartment
Open
Closed
Rell indicator
Cover for rinse aid
Open by turning and lifting the cover!

12
Program Description
Programme Auto
wash
Heavy
wash
Normal
wash**
Normal
wash
Delicate
wash
Quick
wash
Rinse &
Hold
Options -- - -
Prewashes 1-3202000
Main wash (°C) 55-65 55 55 65 50 60 -
Number of rinses 2-3322221
Final rinse
temperature (°C)
60 60 60 70 50 60 -
Consumption values*
1. Wash time
(approx.
hours:minutes)
2:05-3:05 3:15 2:50 2:10 1:55 1:00 0:04
1. Energy (approx.
kWh)
1,1-1,6 1,3 1,1 1,5 0,9 1,0 0,01
2. Wash time
(approx.
hours:minutes)
1:45-2:35 2:50 2:35 1:50 1:35 0:45 0:04
2. Energy (approx.
kWh)
0,7-1,0 0,6 0,8 0,9 0,5 0,6 0,01
Water consumption
(liter)
14-23 19 11 17 10 10 3
*Consumption values vary depending on the water supply temperature, the ambient temperature, the size of
the load, the selected options and more.
** The energy label performance gures are based on this programme.
1. Connection to cold water, approx. 15 °C
2. Connection to hot water, approx. 60 °C

13
Cleaning
The dishwasher tub is made of stainless steel and is
kept clean through normal use.However, if you have hard
water, limescale deposits may form in the machine.
If this happens, run a normal wash program with two
tablespoons of citric acid in the dishwasher detergent
compartment.
Spray arm
Coarse lter
Fine lter
Tubular
strainer

The coarse lter traps larger food particles, which cannot
get past the drain pump. Empty the coarse lter as
necessary.
1. Lift the coarse lter by the handle.
2. Empty the coarse lter. Don’t forget to replace it!

Debris that collects on the ne lter is auto matically
rinsed away during each wash. However, the ne lter
and its pipe section should be cleaned once or twice a
year.
1. Turn the handle once counter-clockwise.
2. Lift the pipe section straight up by the handle. Free
the coarse lter to clean the pipe section.
1x
3. Remove and clean the ne lter
4. Replace in reverse order. Ensure that the edges are
properly sealed when replacing the ne lter.
5. Lock the lter in place by turning the handle clockwise
to the stop position: the handle should point out from the
dishwasher.
NOTE:
The dishwasher must not be used without the lter in
place!
An improperly tted coarse lter may addect the
dishwashing result!
Drain pump
The pump can be accessed from inside the machine.
1.Cut the power to the machine by pulling out the plug!
2.Remove the coarse lter and pipe section.
3.Remove the small tted piece at the left of the bottom
drain (see the image below)
1x
4.You can release and turn the pump blade by inserting
your nger into the hole and release anything blocking it.
5. Reinstall the tted piece and lters.
6. Plug the plug into the wall socket.

14
If the machine still does not start and a buzzing sound is
heard, the overow guard has been activated.
• Shut o the water.
• Pull the plug out from the wall socket.
• Call the service division.
NOTE!
Do not forget to reinstall the tted piece.
Lower spray arm
Holes and bearings can sometimes become blocked.
Pull the lower spray arm straight up to release it.
Remove any debris using a needle or the like. The spray
arms also have holes underneath.
Upper spray arm
The upper basket must be removed before the upper
spray arm can be released.
Pull out the upper basket and turn the basket catch on
each runner outwards (see illustration). The basket can
now be removed.
Loosen the upper spray arm in the same manner as the
lower spray arm and clean it.
Door
When cleaning the edge around the door, use only a
slightly damp cloth (with a little cleaner if necessary)
.
WARNING!
Do not use a spray bottle or the like around the door lock.

15
Settings
Programming
Some of the machine’s functions can be reprogrammed.You get into the machine’s change program using the
machine’s ordinary buttons as per the instructions below. The selection will be retained until the next time you reset this
function.
Even if the machine is turned o at the main switch or loses power for any other reason,
all selections registered before the interruption of power will be retained.
Child-safe button lock
You can prevent a child starting the machine by accident or changing the settings by programming the machine with a
button lock, which requires the Temperature and Drying buttons to be pressed simultaneously to start up the machine.
The button lock will automatically be reactivated after three minutes.
1. Switch o the dishwasher with the main switch.
+
2. Hold in the Temperature and Drying buttons while pressing the main switch. The
Temperature, Drying and start symbols will ash. Release the Temperature and Drying
buttons.
P
3. Press the Program button – when the Auto wash symbol is lit, the button lock has been
activated.
4. Then press the Start/Stop button to store the setting.
or Reset:
1. Switch o the dishwasher with the main switch.
+
2. Hold in the Temperature and Drying buttons at the same time as pressing the main switch.
P
3. Press the Program button – when the Auto wash symbol goes out the button lock has
been deactivated.
4. Then press the Start/Stop button to conrm the setting.
Setting a signal
If you want the machine to signal when the wash is complete, you can program it to do this. The machine is set
without a signal by default.
1. Switch o the dishwasher with the main switch.
2. Hold in the Delayed start button at the same time as you press the main switch. The Delayed start
and start symbols will then ash. Release the buttons.
P
3. Press the Program button – when the Auto wash symbol lights, the signal is activated.
4. Press the Start/Stop button and the setting will be stored until next time you want to make a
change.
or Reset:
1. Switch o the dishwasher with the main switch.
2. Hold in the Delayed start button at the same time as you press the main switch. The Delayed start
and start symbols will then ash. Release the button.
P
3. Press the Program button – when the Auto wash symbol goes out, the signal is deactivated.
4. Press the Start/Stop button and the setting will be stored until next time you want to make a
change.

16
Setting water hardness
If you have a dishwasher with a water softener, you may need to change the setting, depending on the degree of
hardness of the water. Phone your local Water Board to check the water hardness in your area. The dishwasher is set
for low water hardness on delivery.
1. Switch o the dishwasher with the main switch.
+
2. Hold in the Start/Stop and Drying buttons at the same time as pressing the main switch. The start
symbol will then ash. Release the buttons.
P
3. Press the Program button from one to six times depending on the hardness of the water. Program
symbols will light up as you press. See illustration.
Setting water hardness °dH °fH
******0-5 0-9
6-8 9-14
9-14 15-25
15-19 26-34
20-29 35-52
30-44 53-79
45+ 80+
*All program indicators extinguished: Machines without water softeners and machines with water softeners
and low water hardness.
4. Press the Start/Stop button and the setting will be stored until next time you want to make a
change.

17
Fault indications / Troubleshooting
Display Type of fault Action
ashes Overlling Call the service division.
+ ashes Water outlet fault See ”Possible causes” in the chapter Troubleshooting.
ashes Water inlet fault Check that the water tap is on.
ashes Inlet valve leakage Turn o the water tap and call the service division
To remove the fault indications from the display, turn o the main switch and then turn it back on again.
Problem Possible causes Action
The dishes are not clean • The spray arms are not rotating. • Lift o the arms and clean.
• Old dishwasher detergent.NOTE!
Detergent is a perishable.
• Avoid large packs.
• Incorrect dosage of detergent. • Dispense according to the level of
water hardness.
• Insuciently powerful
dishwashing program.
• Select the Temperature normal
option or switch to a more
powerful program.
• Incorrect program chosen. • Change to a more intensive
program.
• Incorrect loading of the
dishwasher.
• Do not cover china with large
bowls or similar.
•Avoid placing very tall glasses in
the corners of baskets.
• Glasses and cups have tipped
over during the wash.
• Load the china securely.
 • Dishwasher tted with water
softener is leaking salt.
• Check that the cover of the salt
compartment is properly screwed
on. Otherwise phone for Service.
• Incorrectly set water softener. • See the chapter on water
softeners.
• Incorrectly set rinse aid dispenser. • See the chapter on rinse aid.
• The salt compartment is empty. • Top up with salt.
• Phosphate-free detergent in
combination with hard water.
• Change detergent.
• Too high a temperature and/
or too much detergent can
cause etching on (crystal) glass.
Unfortunately this cannot be
remedied, only prevented!
• Wash (crystal) glass at a low
temperature and dispense
dishwasher detergent with care.
Contact the dishwasher detergent
manufacturer.
The china has a whitish-blue

• Too high dosage of rinse aid. • Reduce dosage. See the chapter
on rinse aid. If the water is very
soft, you could try diluting the
rinse aid (1 part rinse aid, 1 part
water).
Troubleshooting

18
Problem Possible causes Action
Stains on stainless steel or
silver
• Certain food remnants such as
mustard, mayonnaise, lemon,
vinegar, salt and dressings can
cause stains on stainless steel if
allowed to remain for any length
of time. All stainless steel can
mark silver if allowed to come into
contact during the dishwashing
process. Aluminium can also
cause stains on dishes.
• Rinse o food residue of this type
if you do not intend to start the
dishwasher immediately.
• Seperate your cutlery into the
various compartments in the
basket. Make sure silver and
stainless steel are not together.
Stains which remain after
dishwashing
• Lipstick and tea can be dicult to
remove.
• Change to a detergent with bleach.
Rattling sound during
dishwashing
• The dishes are not properly loaded
or the spray arms are not rotating.
• Check that the china is loaded
securely. Spin the spray arms to
make sure that they rotate.
The machine will not start • You have forgotten to switch on the
main switch.
• Check.
• The door is not properly closed. • Check.
• A fuse has blown. • Check.
• The plug is not plugged in. • Check.
• The water tap is o. • Check.
• Overlling/leakage • Check.
• A droning sound (drainage pump)
can be heard from the machine,
this does not stop when the power
is switched o using the main
power switch.
1. Close the water tap.
2. Pull out the plug.
3. Call a service engineer
Water remains in the
machine
• Obstruction in the drain hose. • Disconnect the drain hose where
it is connected to the sink’s water
trap. Check that no debris has
become stuck. Is the cone-shaped
part of the pipe cut so that the
diameter is at least 16 mm?
• Kinks in the drain hose. • Check that the hose is free from
kinks or sharp bends.
• The lters are clogged. • Clean out the coarse lter, the ne
lter and the lter.
• Items in the drain pump. • Clean out the drain pump. See
chapter on cleaning
Bad odor in the machine • Dirt along the strips and in
corners.
• Clean with a dish brush and low-
lather detergent.
• Low-temperature programs have
been selected for a prolonged
period.
• Run a Normal Temperature
program around once a month.
The dishes are not

• Drying power too low. • Activate the Normal drying option.
• The machine is not fully loaded. • Put a full load in the machine.
• The rinse aid has run out or the set
dose is too low.
• Replenish rinse aid or increase the
dose of rinse aid if required.
• Open the door slightly once the
program has nished.

19
Perfomance information
Energy labelling
European test standard: EN 50242
Number of place settings: 12
Dishwashing programmes: Normal wash 55°C, No options
Program time: 2:50 hours:minutes
Connection: Cold water 15 °C
Test method noise measurement: IEC-704-3
Dosages during testing
Detergent: In accordance with EN 50242
Prewash: 5 gram
Main wash: 25 gram
Rinse aid: In accordance with EN 50242
Rinse aid dosage: 3
Height: 857-915 mm
Width: 596 mm
Depth: 550 mm
Weight: 48 kg/51 kg with water
softener*
Capacity: 12 place settings**
Water pressure 0.03-1.0 MPa (0.3–10 kp/cm2)
Loading of performance test
spinach minced
meat
Upper basket with 12 place settings EN50242 Lower basket with 12 place settings EN50242
1.Teaspoons
2. Dessertspoons
3. Soupspoons
4. Forks
5. Knives
6. Serving cutlery - fork
7. Serving cutlery – gravy ladle
8. Serving cutlery - spoons
Electrical connection See type plate.
Rated power See type plate.
*Weight can vary due to dierent specications.
**In accordance with standard, EN 50242

20
Installation instructions
It is important that you read through and follow the
instructions and directions below. Conduct installation
and connection in accordance with the separate
installation instructions.
Safety instructions
• Connections to electricity, water and drainage must be
performed by a qualied professional. Electrical, water
and drainage installations must be carried out by a
qualied professional.
• Always follow applicable regulations for water, drainage
and electricity.
• An incorrect or awed installation can result in higher
consumption of energy, water and detergent, which
can result in increased costs and poorer dishwashing
results.
• Place a watertight protective tray on the oor under the
dishwasher to prevent damage from any water leaks.
• Before screwing the dishwasher into place, test the
dishwasher by running the Rinse & Hold programme.
Check that the dishwasher lls with water and drains.
Check also that none of the connections leak.
WARNING!
Turn o the water supply before beginning the
installation!
WARNING!
The plug must be disconnected or power to the socket
turned o while the work is carried out!
Setup
• The recess and connection dimensions are included
in the separate installation instructions. Check that all
dimensions are correct before starting the installation.
• Make sure the area on which the dishwasher is to be
installed is rm. Adjust the adjustable feet so that the
dishwasher is level. Tighten the lock nuts.
• Stronger door springs are available for purchase for
dishwashers with a tted wooden door. Springs are
available for various weights and sizes of wooden door.
Door springs can be purchased from the retailer who
sold you the dishwasher.
Drainage connection
• See the separate installation instructions for all
necessary information.
• The drainage hose may be extended by a maximum
of 3 m (the total length of the drainage hose must not
exceed 4,5 m). Any joins and connecting pipes must
have an internal diameter of at least 16 mm. However,
the drainage hose should ideally be replaced with a
new hose without joins.
• No part of the drainage hose may be more than 950
mm above the bottom of the dishwasher. The hose
must not be routed directly to the oor drain or similar.
In such cases, the hose can act as a siphon and empty
the dishwasher.
• The hose must always discharge at least 350 mm
above the bottom of the machine.
• Ensure that the drainage hose has no kinks.
NOTE!
The hose must be attached at the same height as the
underside of the sink.
Connection to water supply
• Use only the supply hose provided with the dishwasher.
Do not re-use old hoses or other spare supply hoses.
• The supply pipe must be tted with a stopcock. The
stopcock must be easily accessible, so that the water
can be shut o if the dishwasher has to be moved.
• Once the installation is complete, the stopcock should
be opened to allow the pressure to settle for a while
and to check that all connections are tight.
Connect to cold water...
If you use oil or electricity to heat your home.
Connect to hot water (max. 70 °C)...
If you use, for example, district heating, solar power or
geothermal power to heat your home.
Electrical connection
Information about the electrical connection can be found
on the serial number plate. This specication must match
the electricity supply.
Dishwashers tted with a plug must be connected to an
earthed socket.
The electric wall socket must be placed outside of the
installation area to be easily accessible after installing
the dishwasher. Do not use an extension cord!
NOTE!
Repairs and maintenance relating to safety or
performance must be carried out by a qualied
professional.