Gradient Lens LUXXOR User manual

PORTABLE CAMERA
LUXXOR® PORTABLE
vidEO CAMERA
User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
207 Tremont Street, Rochester, New York 14608
800.536.0790
Fax: [phone]
REV. 412

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
2 3
WARNINGS
Luxxor® Portable Video Camera
The Luxxor Portable Video Camera (LPC) easily connects
to ANY Hawkeye® Rigid or Flexible Borescope! When
connected, the LPC delivers sharp, bright video and
still images. Borescope inspection images can then be
viewed “live,” and captured, documented, and e-mailed!
PORTABLE CAMERA
Table of Contents
Warnings ......................................................................Page 3
Set Up ............................................................................Page 4
PVM Operation ...........................................................Page 12
Troubleshooting ..........................................................Page 21
Specifications..............................................................Page 21
Notices ..........................................................................Page 22
Warranty / Service .....................................................Page 22
WARNINGS:
If you have purchased the Computer Ready viewing option
(VC-USB2),
INSTALL THE SOFTWARE BEFORE CONNECTING
THE VC-USB2 TO YOUR COMPUTER!!!
If you fail to do this your
computer is likely to automatically install its own, incorrect
drivers which will NOT work and will be next to impossible
to uninstall.
Do not attempt to disassemble the product. You will break the
camera. Disassembly will void your warranty.

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
4 5
Connect the composite video output connector to your monitor’s composite input.
Normally this is an RCA phono jack, usually colored yellow, and labeled Video,
Video In, Composite In, or just Input.
Note: The larger the video screen, the poorer the image resolution will appear at a
particular viewing distance.
The composite video output connector may also be connected to a monitor with an
S-Video Input or BNC Input with an appropriate adapter (sold separately).
Plug the power supply into a 100-240 VAC, 50-60 Hz outlet.
Adapters for a few common power outlets are included.
(UK, EU, etc.)
The Luxxor® Portable Camera is powered ON when the
cable is connected and the power supply is plugged in.
There is no power switch.
SETUPSETUP
S-Video (Y/C) BNC
Y-cable
Composite
Video Out
6-Pin
Power Supply
Luxxor® Portable Camera
The Luxxor® Portable Camera is shipped with
a Y-cable, which allows it to be connected
to any video monitor with a composite input
(NTSC format).
The Y-cable has a 6-pin circular connector
at one end. The other end splits into two: an
RCA phono plug providing composite video
output and a power supply.
Attach the 6-pin connector to the Luxxor® Portable
VideoCamera.

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
6 7
1. Insert the included CD into your computer’s CD-ROM drive.
2. Open the My Computer window and double-click on the CD-ROM icon.
3. Double-click on the installer program – Video ToolBox Installer USB2b.exe.
4. The program will display the following window:
If you are not sure that DirectX 9.0 or later is already installed, press the INSTALL button.
The software will not load if a newer version already exists on your computer.
5. The installer will now move to the Install Video ToolBox step. Click INSTALL to install
the Video ToolBox software.
SETUPSETUP
Computer Ready Option
Install the Software
WARNING: The included software drivers
MUST be installed BEFORE the VC-USB2 is
connected to your computer’s USB port.
To attach the Luxxor® Portable Camera to your Hawkeye® Pro series borescope:
1. Pull back the grooved ring at the head of the camera.
2. Insert the borescope eyecup fully into the camera head.
3. Release the grooved ring.
Focus the image on your monitor by rotating the focus ring of the Hawkeye® Pro
series borescope.
The Luxxor® Portable Camera is designed to be used with Hawkeye® Pro series
borescopes. It may be used with other borescopes, but their focusing controls
may not be easily accessible.
Attach the Camera to Your Borescope
Focus Ring
Pull back Release
Insert

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
8 9
SETUPSETUP
7. When the driver installation has completed, you will see the following window:
The Computer Ready (VC-USB2) viewing option includes the VC-USB2 image
capture interface.
The VC-USB2 image capture interface connects to the Y-cable of the Luxxor®
Portable Camera and converts the analog composite video signal from the camera
to a digital signal for input to your computer’s USB port.
6. After the Video ToolBox software has been installed you will see the window
below. Press the INSTALL button to install the USB2.0 adapter drivers. If the
drivers were already installed then press the SKIP button to continue.
Note: There may be a delay after you press the Install button, but before the
Windows Installer window opens. Wait for the InstallShield window to open.
Click NEXT and then FINISH in the next window. Do not plug the VC-USB2
capture device into the computer until the driver installation is completed.
VC-USB2
USB Connector

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected] 1110
SETUPSETUP
Also check to make sure there is no protective cap on the end of the scope’s
insertion tube.
The Video ToolBox Help file has a complete description of all the features
of the program as well as hints on how to capture the best quality images
and videos.
Refer to the included Video ToolBox manual to learn how to capture and store
images and videos, as well as how to annotate and label images and more.
Composite Input
Plug the power supply into a 100-240 VAC, 50-60 Hz outlet.
Adapters for a few common power outlets are included.
(UK, EU, etc.)
The Luxxor® Portable Camera is powered on when the
cable is connected and the power supply plugged in.
There is no power switch.
After the software has been properly installed, connect
the composite output from the Y-cable to the composite
input (yellow) of the VC-USB2.
If not already done, connect the 6-pin circular connector
of the Y-cable to the Luxxor® Portable Camera.
Now plug the USB connector of the VC-USB2 capture device into the USB
port you plan to use. Note: If you later plug the VC-USB2 into a different
USB port on your computer, the Found New Hardware Wizard will run
again. In some versions of Windows you will see a warning screen that the
device driver has not passed Windows Logo testing. If this appears, click
CONTINUE ANYWAY.
Installation is now complete. Double-click the Video ToolBox icon on your
desktop to start the program. When the program starts up, you should
have a live image on your screen.
If you have no live image, click the Settings button and choose Video
Device in the left-hand column of the window that appears. Make sure that
the Video Source box is set to Video Composite as shown below.

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
The PVM displays live video and captured still or video images on its built in LCD display.
It can output live video to an external monitor via a composite signal connector and the
included cable. Stored images can be downloaded to a computer via the USB port and
included cable, or through the removable SD memory card. (Details are on next page.)
PVM Operation
Turn the PVM’s power on by pressing and holding the power button for 2-5 seconds.
The Gradient Lens logo will appear. Then the word CAMERA and the battery and
memory status indicators will appear for a few seconds.
When these indicators disappear the unit is in Normal Mode, displaying a live image
from the camera.
To turn the unit off, push and hold the power button for 1-2 seconds until it turns off.
Power ON / OFF
10
Main Controls
OK ESC
Power
PVM OPERATION PVM OPERATION
12 13
12-Pin 6-Pin
6
LPC
12
PVM
Portable Video Monitor Option
If the Portable Video (PVM-DV) viewing option is
chosen, the included cable will have a circular
connector at each end, one 6-pin and one 12-pin.
Connect the 6-pin end to the Luxxor®
Portable Camera and the 12-pin end
to the PVM. The camera is powered
from the PVM’s battery for completely
portable use.
Charging the PVM
To charge the PVM, connect the
charger lead to the jack labeled DCIN
on the PVM. Then plug the charger
into a 100-240 V, 50/60 Hz outlet. Full
charge takes about 2 hours. The PVM
will not operate with the charger
plugged in when the battery is nearly
fully charged.
Note: There is no charging indicator
light. The battery status indicator
will appear in the display when
booting up.

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
14 15
In Normal Mode, press the large black button. If you hold the button down,
the captured image will remain displayed until the button is released.
Still photo files are saved as .JPG.
In Normal Mode, press ESC to display the memory and battery indicators.
Memory capacity remaining is displayed as a percentage. Low battery power
is indicated by the battery status indicator depicting a less than full charge and
turning yellow.
Capture a Still Photo
Memory & Battery Charge Indicators
Normal Mode:
In Normal Mode, press the gray button to start recording. The elapsed
time display will be visible in the lower left of the image to indicate that you
are recording. Press the button again to stop recording and save the clip.
Pressing the button will also stop the recording and save the clip. Video
files are saved as .ASF.
Capture a Video Clip
Battery Status
Memory Remaining
PVM OPERATIONPVM OPERATION
Take care to insert the SD card with the correct orientation
– contacts should be visible when inserting the card with
the video display screen facing you.
CAUTION: Do not remove the SD memory card
during capture operations, data will be lost and the memory
card may be damaged.
Installing the SD Memory Card
There are three operating modes:
Normal Mode
Displays current camera input and date/time. From this mode still pictures and
video are captured.
Image Review Mode
Displays captured still pictures and video.
Menu Mode
File maintenance, system settings, etc.
The unit powers up in Normal Mode.
From Normal Mode
Enter Image Review Mode by pressing or
Enter Menu Mode by pressing OK.
Return to Normal Mode from any other mode by pressing ESC.
Operating Modes

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
16 17
Deletes all saved files, video and still photos.
When this function is selected, the unit displays
a frame which includes two options. Use and
to select YES or NO and press OK to confirm.
Delete All
Date / Time Setup
Menu Mode:
This function transfers the video signal to and from
an auxiliary display using the supplied cable. The
unit will automatically switch to the auxiliary display
when the cable is connected and will revert to the
built in display when the cable is disconnected. This
function will allow you to toggle between displays
if both are connected. Simply press OK while this
function is selected to toggle between displays.
Video Output
Sets the date and time. Select this
function and use the and buttons
to select year/month/day or hour/
minute/second fields, then press
the and/or buttons to scroll
through the numbers to set the date
and time. If DISPLAY indicates ON
status, the date and time will be
displayed on the screen. Captured
images will always include a time/
date stamp. Confirm changes by
pressing OK.
ERASE ALL
YES NO
MENU
DELETE ALL
VIDEO OUTPUT
DATE / TIME SETUP
LANGUAGE
VIDEO FORMAT
MENU
DELETE ALL
VIDEO OUTPUT
DATE / TIME SETUP
LANGUAGE
VIDEO FORMAT
TIME SET
2008 / 01 / 01
00 : 00 : 00
DISPLAY ON
PVM OPERATIONPVM OPERATION
Push the or button to enter Image Review Mode. You can scroll forward or
back through the photos and videos using the or buttons. Video files may be
played, paused, and resumed by pressing the button. While a still or video file is
displayed (video not playing), pressing the OK button will bring up the DELETE menu.
Select YES and press OK to delete the file. To exit Image Review Mode, press ESC.
In Normal Mode:
Press the OK button to display the
Main Menu as follows:
DELETE ALL
VIDEO OUTPUT
DATE/TIME SETUP
LANGUAGE
VIDEO FORMAT
AUTO POWER OFF
You can scroll through the functions on this menu using the
and buttons, and select the function using the OK button.
Press or to enter Image Review Mode. Scroll to
the required file using the or buttons. When the
required photo or video file is displayed, press OK.
A frame will be displayed to confirm the delete function.
Select YES with or and press OK to confirm.
View Captured Photos or Video Clips
Display Main Menu
Delete a Single File
Image Review Mode:
Menu Mode:
DELETE
YES NO
MENU
DELETE ALL
VIDEO OUTPUT
DATE / TIME SETUP
LANGUAGE
VIDEO FORMAT

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Select this function by pressing the OK
button and use the and buttons to
select time for auto power off or to disable
the auto power off function. Press OK to
confirm.
Use the included AV cable to connect your auxiliary display to the jack on the side of
the PVM. Note: The display must accept a composite input. The unit will automatically
switch to the auxiliary display when the cable is connected. You may switch between
the displays by using the VIDEO OUTPUT function on the main menu. The PVM display
and the external display cannot be viewed at the same time.
The video output format to the auxiliary display may be switched between
NTSC and PAL by using the VIDEO FORMAT function on the main menu.
Auto Power Off
Connecting to an Auxiliary Display
Menu Mode:
MENU
VIDEO OUTPUT
DATE / TIME SETUP
LANGUAGE
VIDEO FORMAT
AUTO POWER OFF
AUTO OFF
DISABLE
5 MIN
10 MIN
15 MIN
30 MIN
Video OutAV Cable
PVM OPERATIONPVM OPERATION
18 19
If your unit is supplied with a language option this function will allow you to
select English or the optional language.
Language
Menu Mode:
This function allows you to choose the
format of the output video signal for an
auxiliary display. The options are NTSC and
PAL. Use the and to select and press
OK to confirm.
Video Format
While the TV OUTPUT options are
displayed, pressing the button will
display the FACTORY SETUP menu.
Here the factory settings for the video
display may be changed or reset.
Use and and press OK to select
the property to be changed. Then
use and to change the setting
and OK to confirm. Holding the or
buttons down for a couple of seconds
will cause the settings to change more
rapidly. DEFAULT restores the original
factory settings.
MENU
DELETE ALL
VIDEO OUTPUT
DATE / TIME SETUP
LANGUAGE
VIDEO FORMAT
TV OUTPUT
NTSC
PAL
MENU
BRIGHTNESS 128
CONTRAST 120
HUE 114
SATURATION 90
DEFAULT

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Nothing on LCD screen: Battery power too low.
Recharge the battery.
No image – but words and status symbols on LCD
display: Insertion tube is not connected securely.
Reattach the insertion tube.
Cannot capture photos or video: No SD Card inserted.
Shut down: Battery has discharged below operating
threshold. Recharge battery.
!!! No functions working!!! If all functions freeze or fail,
first try to power the unit off and restart. If the unit does
not recover, insert a non-conducting probe, such as a
toothpick, into the hole on the back of the PVM and use it
to press the internal reset button to perform a
system reset.
PVM OPERATION
PVM Troubleshooting Tips
Reset
TROUBLESHOOTING / SPECIFICATIONS
Sensor 1/4” CCD
Effective Pixels 768 x 494
Scanning 2 : 1 Interlace
Resolution 520 TV Lines
Output Composite
Output Format NTSC
Length 6.25” (159 mm)
Max Diameter 1.74” (44.2 mm)
Weight 6.3 oz. (178.6 gm)
LPC Specifications
20 21
The PVM can download saved images through its USB port. Plug in the Mini USB 1.1
connector of the included USB cable into the USB port on the PVM. Then plug the other end
into a USB port on your PC and open the drive associated with the chosen port. The stored
images are contained in the location X:\DCIM\100MEDIA where X is the drive letter. JPGs can
be viewed with Windows Picture Viewer, and .ASF video files play in Windows Media Player.
Transferring Image Files to a PC
Tripod Stand
Alternatively, the SD memory card may be removed from the PVM and inserted into
your computer’s card reader.
USB Cable
A compact tripod stand for the PVM is included to
enable one-handed operation of the Rigid Video
Borescope.
Attach the tripod stand to the threaded socket on
the back of the PVM.
Adjust the tripod head and legs to allow the PVM to
stand on a firm surface.

Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
Luxxor® Portable Video Camera User Guide
Phone: [phone] fax [phone] gradientlens.com [email protected]
NOTICES / WARRANTY
22
This device has been tested to be in compliance with part 15, Class A of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
USA
Canada
Warranty
Gradient Lens Corporation warrants the Luxxor® Portable Camera to be free of defects
in material and workmanship and to perform in accordance with the manufacturer’s
specifications when subject to normal use and service for a period of one year from the date
of purchase. Gradient Lens Corporation will either repair or replace components found to be
defective or at variance from the manufacturer’s specifications within this time at no cost to the
customer. It shall be the purchaser’s responsibility to return the instrument to the authorized
service center.
This warranty does not cover breakage or failure due to tampering, misuse, neglect, accidents,
improper installation, modification, shipping, or to improper maintenance, service and cleaning
procedures. This warranty is also void if the instrument is not used in accordance with the
manufacturer’s recommendations, or if required service is performed by anyone other than a
Gradient Lens Corporation authorized agent. No other express or implied warranty is given.
Service
Should service of the equipment be required: Call Gradient Lens Corporation to obtain a
return material authorization (RMA) number and shipping directions.
Telephone: .....................585.235.2620
Fax: ..................................585.235.6645
E-mail: [e-mail]
Toll Free: .........................800-536-0790 (in US only)
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003
du Canada.