Specications
AK-HC3800 Studio Handy Camera
Power Supply: 12 V DC (during external power supply operation)
190 V DC (when CCU is connected)
Power Consumption: 25 W (during external power supply operation,
camera only)
53 W (maximum power during external power supply
operation when maximum power supplied for each
output connector while all accessories are connected)
60 W (maximum power when CCU is connected and
maximum power supplied for each output connector
while all accessories are connected)
Operating Temperature: –10 °C to 45 °C (14°F to 113°F)
Preheating required at temperatures below 0°C (32°F)
Storage Temperature: –20 °C to 60 °C (–4°F to 140°F)
Operating Humidity: 10 % to 85 % (no condensation)
Weight: Approx. 3.7 kg(approx. 8.16 lb)
Dimensions (W x H x D): 135 mm x 260 mm x 367.5 mm
(5-5/16 inches x 10-1/4inches x 14-7/16 inches)
excluding protrusions
Pickup Device: 2/3-type 2.2 million pixel IT, CCD x 3
System: GBR pickup system
Color Separation Optical system:
f/1.4 prism
Optical Filter: ND: Clear, 1/4, 1/16, 1/64
Lens Mount: Bayonet type
Output standard: SMPTE 292M
Sensitivity: F11 (59.94 Hz)
F12 (50 Hz)
Horizontal Resolution: 1100 TV lines
S/N: 60 dB or higher
Horizontal Frequency: 33.716 kHz, 1125 line frame (59.94 Hz)
28.125 kHz, 1125 line frame (50 Hz)
Vertical Frequency: 59.94 Hz or 50 Hz, interlace
MIC Input: –60 dBu to 4 dBu (XLR 3-pin female x 2)
Gain selected by camera menu
Intercom: XLR 5-pin female x 1
Input: -60 dBu to -20 dBu
Output: 100 mW max.
HD SDI Output
: BNC x 2 (
HD SDI 1/HD SDI 2)
HD signal = 0.8 V [p-p], 75 Ω
The HD SDI 2 signal output can be added to the
regular images using the camera menu item setting
and switched to the VF or RET image output.
Prompter Output: BNC x 1, VBS signal = 1.0 V [p-p], 75 Ω
DC OUT: 12 V, MAX. 1A
RET CONTROL Terminal: Round 6 pin x 1
VF: Round 20 pin x 1, D-Sub 29 pin x 1
Power Switching: CCU, OFF, EXT
USER 1/2/3: Functions specied by menu items can be assigned to
the switch.
RET A/B Selection: For selecting the return signal
RET/PTT Switching: RET, PPT
Gain Selection*1: LOW, MID, HIGH
Output Selection*1: CAM, BAR, TEST
White Balance Mode*1: A, B, preset
Shutter Speed Selection
*1: 1/100, 1/120, 1/125, 1/250, 1/500, 1/1000, 1/1500,
1/2000
Intercom: MIC ON/OFF, receiving level, or PGM level
MIC Setting: MIC power, MIC gain, MIC1 selection
*1: When the CCU is connected, the selection functions cannot be used. Control is
performed from the ROP.
AK-HCU200 Camera Control Unit (CCU)
Power Supply: 100 V to 240 V AC, 50/60 Hz
Power Consumption: 170 W (Without CAMERA connected: 32 W)
Capacity for Supplying Power to a Camera:
190 V DC, 0.6 A
Operating Temperature: 0 °C to 40 °C (32 °F to 104 °F)
Operating Humidity: 10 % to 90 % (no condensation)
Dimensions (W x H x D): 424 mm × 88 mm × 400 mm
(16-11/16 inches × 3-7/16 inches × 15-3/4 inches)
Excluding protrusions
Weight: Approx. 6.6 kg(approx. 14.6 lb)
Video Output: HD SDI/SD SDI: 4 lines
(2 lines shared with picture monitor output*2)
Analog composite: 1 line
(1 line shared with picture monitor output*2)
Return Input: HD SDI/SD SDI: 2 lines
(switched depending on the setting)
VBS: 1 line
Prompter Input: 1 line, Analog composite
Reference Input: 1 line (1 loop-through line)
Black burst/tri-level*3
Microphone Output: 2 lines (XLR, 3-pin, male), 0 dBm/600 Ω
Intercom: XLR, 5-pin, female
Input: –55 dBu to –10 dBu
Output: 100 mW (max.)
COMMUNICATION: Intercom input/output: 2 lines (1/2*2)
(0 dBm, 600 Ω, RTS/4W*2)
PGM: 1 line, input (0 dBm/600 Ω)
Tally input: Red, Green, 1 input each
ROP interface: RS-422, 1 line, 12 V output
MSU interface: RS-422, 1 line, GPI for control
LAN port: 1 line (10Base-T/100Base-TX, RJ45, crossover cable,
category 5 or above)
For computer connection
*2: Depending on the setting, only one of them can be selected at one time.
*3: The black burst signal and tri-level sync signal of the reference input are recognized
automatically.
AK-HRP200G Remote Operation Panel (ROP)
Power Supply: 12 V DC
Power Consumption: 4.2 W
Operating Temperature: 0 °C to 40 °C (32 °F to 104 °F)
Storage Temperature: −20 °C to 60 °C (−4 °F to 140 °F)
Operating Humidity: 90 % or less
Dimensions (W x H x D): 92 mm x 308 mm x 55 mm
(3-5/8 inches x12-1/8 inches x 2-3/16 inches)
excluding protrusions
Weight: Approx. 1.3 kg(approx. 2.87lb)
CCU Control: • Control signals (camera, CCU control)
• Power supply (12 V DC)*4
• Tally control signal
PREVIEW control: Contact output
Maximum cable length: 50 m (164 ft)
*4: Can be provided from CCU or AC adapter
AK-HVF70G 17.8 cm (7 inch) LCD Color Viewnder
Power Supply: DC 12 V (supplied by the camera)
Power Consumption: 10 W
Operating Temperature: 0 °C to 45 °C (32 °F to 113 °F)
Storage Temperature: –20 °C to 60 °C (–4 °F to 140 °F)
Operating Humidity: 10% to 85% (no condensation)
Dimensions (W x H x D): 243.5 mm x 212 mm x 172 mm
(9-19/32 inches x 8-11/32 inches x 6-25/32 inches)
(with hood attached)
243.5 mm x 212 mm x 85 mm
(9-19/32 inches x 8-11/32 inches x 3-11/32 inches)
(without hood)
Weight: Approx. 1.6 kg(approx. 3.53 lb) (without hood)
Panel Size: 177.8 mm (7.0 inches)
Number of Pixels: 1024 x 600 (WSVGA)
Display Colors: Approx. 16,200,000 colors
Operation Panel: POWER switch x 1, MENU button x 1
SELECT dial x1, Function buttons x 3
Picture adjusting knobs x 3
([BRIGHT], [CONTRAST], [PEAKING])
Connectors: Camera I/F connector (D-Sub 29-pin x 1)
Weight and dimensions are approximate.
Specifications are subject to change without notice.
As of November, 2012