Grandinroad 43674 AQU User manual

Page 1
43674 AQU, Retro Squares Glider Loveseat-Aquatic
43674 PEG, Retro Squares Glider Loveseat-Pear green
43674 RED, Retro Squares Glider Loveseat-Red
43674 WHI, Retro Squares Glider Loveseat-White
PATIO FURNITURE & ACCESSORIES
ASSEMBLY INSTRUCTIONS
IMPORTANT!!!
STOP! PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE
ASSEMBLY. MAKE SURE YOU HAVE ALL THE PARTS AND HARDWARE AS
IDENTIFIED ON THE PARTS LIST.
MISSING PARTS? DAMAGED PARTS? WE CAN HELP YOU FASTER!
CALL OUR CUSTOMER SERVICE CENTER AT BETWEEN
8:00AM AND 8:00PM (EASTERN TIME) MONDAY THROUGH FRIDAY
(CLOSED HOLIDAYS).
OR, VISIT OUR WEBSITE AT: www.grandinroad.com
1-800-491-4958
CARE AND MAINTENANCE
FRAMES
FABRICS (CUSHIONS/SLINGS)
STRAPS
Cleaning
Maintenance
Cleaning -
Maintenance
Cleaning -
Maintenance -
- Use mild soap and warm water. Do not use abrasive materials, cleansers or
bleach products. Rinse with clean water and dry thoroughly.
- Periodically clean and dry thoroughly. Be sure to drain any water
accumulated inside the frames. To thoroughly drain frames, remove foot caps and tilt the
frames, if necessary, to remove all water. This is critical. Water allowed to accumulate
inside the frames and then exposed to sub-freezing temperatures can cause damage to the
frame tubing. Such damage is not covered under warranty. Always clean, drain and dry
thoroughly before storing for the winter. For best results, always store or cover your
furniture when not in use. We recommend commercially available outdoor furniture covers.
Any small nicks or scratches can be covered with a light application of touch-up paint.
** When cleaning or moving large or heavy items, always have two people work together.
Never drag furniture.
Wipe minor spills immediately. Clean with mild soap, warm clean water and
soft cloth. Do not use abrasive materials, cleansers or bleach products. Although fabric has
been treated to resist stains, occasional use of commercially available fabric cleaners may
be necessary. Follow manufacturer's instructions.
- The best way to maintain the beauty of cushions and slings is to store them
in a dry area and out of the elements when not in use or cover with commercially available
outdoor furniture covers.
Wash frequently with mild soap, warm water and a soft cloth. Rinse thoroughly
with warm, clean water. Do not use abrasive materials, cleansers or bleach products.
Periodic application of commercially available vinyl cleaners and vinyl
protectors will enhance the look and prolong the life of straps. If your strap chair has
cushions, make sure any vinyl protectors applied are completely dry before placing cushion
back on the chair.

Page 2
Fig.1
Fig.2
A1
D
A2
C1
C2
E
B
E
D
K
J
Q
Q
P
S
Q
L
L
Q
R
Fig.3
GLIDER BRACKET
Step 1:
IMPORTANT NOTE: WE RECOMMEND TWO PEOPLE WORK TOGETHER TO ASSEMBLE THE GLIDER
Remove all protective materials and set parts on a flat, non-abrasive surface. Identify parts packed in carton against the parts list. If you are missing
any parts or are unsure how to proceed with assembly,
.
Assembly references to "left" and "right" are designated by facing the glider and NOT by sitting in it.
please call our Product Specialists immediately at . Do not attempt to assemble
the chair if any parts are damaged or missing.
1-800-491-4958
Attach glider base left leg (A1) to one of the glider base leg support bars (B) using 5/16"x35 mm bolts (I), Ø8.5x1.5 mm washers (L) and 5/16" nuts (P)
as shown in . Repeat on glider base right leg (A2). Repeat entire procedure for remaining glider base leg support bar (B).
Attach glider back frame (D) to glider left arm (C1) using 5/16"x60 mm bolts (G), Ø8.5x1.5 mm washers (L) and 5/16" nuts (P) as shown in .
Attach seat frame to left arm using 5/16"x60 mm bolts (G), Ø8.5x1.5 mm washers (L) and 5/16" nuts (P) as shown in .
Repeat to attach glider seat back (D) and glider seat frame (E) to glider right arm (C2). Attach glider back frame and glider seat frame using a
1/4"x25 mm bolt (J) and a Ø6.5x1.0 mm washer (K) as shown in . Guide bolt and washer through pre-drilled hole in glider seat frame and into
pre-drilled hole on glider back frame.
Step 2:
Do not over tighten.
Step 3:
Do not over tighten.
Do not over tighten.
Fig.1
Fig.2
Fig.2
Fig.3
S
LP
Q
R
I
L
G
Q
L
G
L
G
Q
Q
G
L
LPS
P
L
LP

Page 3
Q
Q
F
N
N
H
Place the completed seat assembly over the glider base assembly. Use 1/4"x65 mm bolts (F) to attach back portion of seat assembly to rear glider
bracket on glider base. From the outside of the glider bracket, insert bolt (F) inward in this exact order through: glider bracket / Ø15x6 mm washer (N)
/ glider seat frame (E) / Ø15x4 mm washer (M) / Ø6.5x1.0mm washer (K) / 1/4" nut (O) as shown in . Use 1/4"x45mm
bolts (H) to attach front portion of seat assembly to front glider bracket on glider base. From the outside of the glider bracket, insert bolt (H) inward in
this exact order through: glider bracket / Ø15x6 mm washer (N) / glider seat frame (E) / Ø15x4 mm washer (M) / 6.5x1.0 mm washer (K) / 1/4" nut (O)
as shown in Repeat entire on opposite side.
Using hex wrench and hex bolt driver provided, tighten all nuts and bolts a few revolutions at a time, alternating between glider bracket connections
until all nuts and bolts are completely tight. Test of operation of glider. Gliding motion should be smooth. Adjust tension on
the glider brackets, nuts and bolts as needed. If nuts and bolts are either too tight or too loose, the glider will not function properly.
Cover all nuts and bolts with covers provided. Your glider is now ready for use.
Step 4:
Do not over tighten.
Do not over tighten. Step 4
Step 5:
Do not over tighten.
1-800-491-4958
Fig.4
Fig.5
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or improper assembly is not covered under our warranty.
Please read all instructions carefully before assembly. If you have any questions regarding your assembly, call our Product Specialists at
.
Fig.4
Fig.5
M
O
K
M
O
K

Page 4
BCS01804
8
5
4
5/16" X 60 MM BOLT HW0261
HW0004
Ø6.5 X 1.0 MM
WASHER
Ø15X4MM
PLASTIC WASHER
PARTS LIST DESCRIPTION QTY ORDER PART #
A1
A2
B
C1
C2
D
E
F
G
H
I
J
K
L
M
GLIDER BASE
LEFT LEG
1
GLIDER BASE
RIGHT LEG
1
GLIDER LEG
SUPPORT BAR
2
GLIDER LEFT ARM
GLIDER RIGHT ARM
1
1
GLIDER BACK FRAME
GLIDER SEAT FRAME
1
1
1/4" X 45 MM BOLT
8
5/16" X 35 MM BOLT HW0128
HW0079
2
1/4" X 25 MM BOLT HW0037
1
32
HW0176
Ø8.5 X 1.5 MM
WASHER
HW0020
1/4" X 65 MM BOLT HW0111
2
4
4
25
PARTS LIST DESCRIPTION
1/4" NUT HW0017
BOLT COVER
QTY
ORDER PART #
HW0006
HEX BOLT DRIVER
HEX WRENCH
1
1
FOOT CAP
FACTORY ASSEMBLY FC0165
GLIDER BRACKET
FACTORY ASSEMBLY
LEG CAP
FACTORY ASSEMBLY
4
Ø15X6MM
PLASTIC WASHER
N
O
P
Q
R
S
T
U
V
HW0033
16
5/16" NUT HW0177
12
G0121
FC0051
HW0241
HEX WRENCH
1
HW0009
HW0022
HW0027
HW0178
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
1/4" NUT COVER
5/16" NUT COVER