Grandstream Networks GUV3050 User manual
Wear the GUV3050 Headset
GUV3050
Wireless Bluetooth Headset
21
Adjust the Headband
3
Headset Components
Base Charging Point
Bluetooth
indicator
switch
Adjustable headband
Volume up
Volume down
Multi-function Cutton
Power on/Power
Busylight indicator
Microphone
USB charging port
boom-arm
Package contents
GUV3050 Carry pouch
USB cable
BT dongle Quick User Guide
Charging Base
GUV3050 BT headset
can be worn only on the
right.
Place the headset receiver to
your ears. Adjust the headband
until it is comfortable, ideally
ensuring that there is virtually
no pressure felt on the ears.
To avoid low or distorted sound, and to provide clear and crisp
telephone calls, the microphone should be positioned within 0.5
inches of your mouth. The microphone boom arm will move in a
YDULHW\RIGLUHFWLRQVWRHQVXUHWKHEHVW¿W
Charge the battery
Option 1: The headset battery can
be charged when connected to a
PC using an USB cable (provided),
or using any micro-USB charger
(not provided).
Option 2: Plug the charging base
into a powered USB port and then
dock the headset.
Option 1
Option 2
Connect to mobile device (using Bluetooth)
Hold the On/2ff/&onnect switch in
theconnect position for 2 seconds until
youhear the voice guided instruction.
TheBluetooth indicator will flash blue.
Follow the voice guided instructions
to connect.
Connect to PC (using BT dongle)
1. Ensure the headset is switched on.
2. Plug the BT dongle into an USB port on
your PC. The headset and BT dongle are
already pre-connected.
Connect the GUV3050 headset
Wear the GUV3050 Headset
GUV3050
Wireless Bluetooth Headset
21
Adjust the Headband
3
Headset Components
Base Charging Point
Bluetooth
indicator
switch
Adjustable headband
Volume up
Volume down
Multi-function Cutton
Power on/Power
Busylight indicator
Microphone
USB charging port
boom-arm
Package contents
GUV3050 Carry pouch
USB cable
BT dongle Quick User Guide
Charging Base
GUV3050 BT headset
can be worn only on the
right.
Place the headset receiver to
your ears. Adjust the headband
until it is comfortable, ideally
ensuring that there is virtually
no pressure felt on the ears.
To avoid low or distorted sound, and to provide clear and crisp
telephone calls, the microphone should be positioned within 0.5
inches of your mouth. The microphone boom arm will move in a
YDULHW\RIGLUHFWLRQVWRHQVXUHWKHEHVW¿W
Charge the battery
Option 1: The headset battery can
be charged when connected to a
PC using an USB cable (provided),
or using any micro-USB charger
(not provided).
Option 2: Plug the charging base
into a powered USB port and then
dock the headset.
Option 1
Option 2
Connect to mobile device (using Bluetooth)
Hold the On/2ff/&onnect switch in
theconnect position for 2 seconds until
youhear the voice guided instruction.
TheBluetooth indicator will flash blue.
Follow the voice guided instructions
to connect.
Connect to PC (using BT dongle)
1. Ensure the headset is switched on.
2. Plug the BT dongle into an USB port on
your PC. The headset and BT dongle are
already pre-connected.
Connect the GUV3050 headset
Wear the GUV3050 Headset
GUV3050
Wireless Bluetooth Headset
21
Adjust the Headband
3
Headset Components
Base Charging Point
Bluetooth
indicator
switch
Adjustable headband
Volume up
Volume down
Multi-function Cutton
Power on/Power
Busylight indicator
Microphone
USB charging port
boom-arm
Package contents
GUV3050 Carry pouch
USB cable
BT dongle Quick User Guide
Charging Base
GUV3050 BT headset
can be worn only on the
right.
Place the headset receiver to
your ears. Adjust the headband
until it is comfortable, ideally
ensuring that there is virtually
no pressure felt on the ears.
To avoid low or distorted sound, and to provide clear and crisp
telephone calls, the microphone should be positioned within 0.5
inches of your mouth. The microphone boom arm will move in a
YDULHW\RIGLUHFWLRQVWRHQVXUHWKHEHVW¿W
Charge the battery
Option 1: The headset battery can
be charged when connected to a
PC using an USB cable (provided),
or using any micro-USB charger
(not provided).
Option 2: Plug the charging base
into a powered USB port and then
dock the headset.
Option 1
Option 2
Connect to mobile device (using Bluetooth)
Hold the On/2ff/&onnect switch in
theconnect position for 2 seconds until
youhear the voice guided instruction.
TheBluetooth indicator will flash blue.
Follow the voice guided instructions
to connect.
Connect to PC (using BT dongle)
1. Ensure the headset is switched on.
2. Plug the BT dongle into an USB port on
your PC. The headset and BT dongle are
already pre-connected.
Connect the GUV3050 headset
Wear the GUV3050 Headset
GUV3050
Wireless Bluetooth Headset
21
Adjust the Headband
3
Headset Components
Base Charging Point
Bluetooth
indicator
switch
Adjustable headband
Volume up
Volume down
Multi-function Cutton
Power on/Power
Busylight indicator
Microphone
USB charging port
boom-arm
Package contents
GUV3050 Carry pouch
USB cable
BT dongle Quick User Guide
Charging Base
GUV3050 BT headset
can be worn only on the
right.
Place the headset receiver to
your ears. Adjust the headband
until it is comfortable, ideally
ensuring that there is virtually
no pressure felt on the ears.
To avoid low or distorted sound, and to provide clear and crisp
telephone calls, the microphone should be positioned within 0.5
inches of your mouth. The microphone boom arm will move in a
YDULHW\RIGLUHFWLRQVWRHQVXUHWKHEHVW¿W
Charge the battery
Option 1: The headset battery can
be charged when connected to a
PC using an USB cable (provided),
or using any micro-USB charger
(not provided).
Option 2: Plug the charging base
into a powered USB port and then
dock the headset.
Option 1
Option 2
Connect to mobile device (using Bluetooth)
Hold the On/2ff/&onnect switch in
theconnect position for 2 seconds until
youhear the voice guided instruction.
TheBluetooth indicator will flash blue.
Follow the voice guided instructions
to connect.
Connect to PC (using BT dongle)
1. Ensure the headset is switched on.
2. Plug the BT dongle into an USB port on
your PC. The headset and BT dongle are
already pre-connected.
Connect the GUV3050 headset
456
Grandstream Networks, Inc.
126 Brookline Ave, 3rd Floor
Boston, MA 02215 USA
Voice: (617) 566-9300
Fax: (617) 249-1987
www.
g
randstream.com
FCC ID: YZZGUV3050
Mute/unmute
microphone
How to use the Headset How to manage multiple calls
Headset on
FUNCTION ACTION
FUNCTION ACTION
LED STATUS
Slide the On switch *UHHQ/LJKWÀDVK
twice in succession
End current call and
answer incoming call
Tap the multi-function
button
Press and hold (2 secs)
the Multi-function button
Press and hold (2 secs)
the Multi-function button
Double-tap the
Multi-function button
Put current call on hold
and answer incoming call
Switch between held call
and active call
Reject incoming call,
when on a call
5HG/LJKWÀDVK
once in succession
%OXH/LJKWÀDVK
*UHHQ/LJKWÀDVKWZLFHDQGEOXH
OLJKWÀDVKRQFHLQVXFFHVVLRQ
%OXH/LJKWÀDVK
1 time per 8 secs
Slide the Off switch
Slide the Pair Button
Tap the Multi-function
button
Double-tap the
Multi-function button
Tap the volume up or
volume down button
Press and hold (2 secs)
the volume down button
Headset off
Pairing
Pairing Successfully
Standby
Answer/End Call
Redial/
Reject Call
Adjust Volume
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Canada Regulatory Information
This device complies with Innovation, Science, and Economic
Development Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :
l'appareil nedoit pas produire de brouillage, et
l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettrele fonctionnement.
The device is compliance with RF exposure guidelines, users can
obtain Canadian information on RF exposure and compliance.
Certification information
Common part：
This equipment complies with radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
U.S. FCC Part 15 Regulatory Information
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Le présent appareil est conforme DX[GLUHFWLYHVGH[SRVLWLRQ RF, les
utilisateurs peuvent DFTXpULUOHVLQIRUPDWLRQVFRUUHVSRQGDQWHVsur
l’exposition aux radiofréquences et la conformité
EU Regulatory Information
Support Frequency Bands and Power:
BT_BR+EDR < 7dBm
The simplified EU declaration of conformity referred to in Article
10(9) shall be provided as follows:
Hereby, [Grandstream Networks, Inc.] declares that the radio
equipment type [GUV3050] is in compliance with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available at the
following ,QWHUQHW address: www.grandstream.com
For Certification, Warranty and RMA information, please visit
www.grandstream.com
456
Grandstream Networks, Inc.
126 Brookline Ave, 3rd Floor
Boston, MA 02215 USA
Voice: (617) 566-9300
Fax: (617) 249-1987
www.
g
randstream.com
FCC ID: YZZGUV3050
Mute/unmute
microphone
How to use the Headset How to manage multiple calls
Headset on
FUNCTION ACTION
FUNCTION ACTION
LED STATUS
Slide the On switch *UHHQ/LJKWÀDVK
twice in succession
End current call and
answer incoming call
Tap the multi-function
button
Press and hold (2 secs)
the Multi-function button
Press and hold (2 secs)
the Multi-function button
Double-tap the
Multi-function button
Put current call on hold
and answer incoming call
Switch between held call
and active call
Reject incoming call,
when on a call
5HG/LJKWÀDVK
once in succession
%OXH/LJKWÀDVK
*UHHQ/LJKWÀDVKWZLFHDQGEOXH
OLJKWÀDVKRQFHLQVXFFHVVLRQ
%OXH/LJKWÀDVK
1 time per 8 secs
Slide the Off switch
Slide the Pair Button
Tap the Multi-function
button
Double-tap the
Multi-function button
Tap the volume up or
volume down button
Press and hold (2 secs)
the volume down button
Headset off
Pairing
Pairing Successfully
Standby
Answer/End Call
Redial/
Reject Call
Adjust Volume
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Canada Regulatory Information
This device complies with Innovation, Science, and Economic
Development Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :
l'appareil nedoit pas produire de brouillage, et
l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettrele fonctionnement.
The device is compliance with RF exposure guidelines, users can
obtain Canadian information on RF exposure and compliance.
Certification information
Common part：
This equipment complies with radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
U.S. FCC Part 15 Regulatory Information
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Le présent appareil est conforme DX[GLUHFWLYHVGH[SRVLWLRQ RF, les
utilisateurs peuvent DFTXpULUOHVLQIRUPDWLRQVFRUUHVSRQGDQWHVsur
l’exposition aux radiofréquences et la conformité
EU Regulatory Information
Support Frequency Bands and Power:
BT_BR+EDR < 7dBm
The simplified EU declaration of conformity referred to in Article
10(9) shall be provided as follows:
Hereby, [Grandstream Networks, Inc.] declares that the radio
equipment type [GUV3050] is in compliance with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available at the
following ,QWHUQHW address: www.grandstream.com
For Certification, Warranty and RMA information, please visit
www.grandstream.com
456
Grandstream Networks, Inc.
126 Brookline Ave, 3rd Floor
Boston, MA 02215 USA
Voice: (617) 566-9300
Fax: (617) 249-1987
www.
g
randstream.com
FCC ID: YZZGUV3050
Mute/unmute
microphone
How to use the Headset How to manage multiple calls
Headset on
FUNCTION ACTION
FUNCTION ACTION
LED STATUS
Slide the On switch *UHHQ/LJKWÀDVK
twice in succession
End current call and
answer incoming call
Tap the multi-function
button
Press and hold (2 secs)
the Multi-function button
Press and hold (2 secs)
the Multi-function button
Double-tap the
Multi-function button
Put current call on hold
and answer incoming call
Switch between held call
and active call
Reject incoming call,
when on a call
5HG/LJKWÀDVK
once in succession
%OXH/LJKWÀDVK
*UHHQ/LJKWÀDVKWZLFHDQGEOXH
OLJKWÀDVKRQFHLQVXFFHVVLRQ
%OXH/LJKWÀDVK
1 time per 8 secs
Slide the Off switch
Slide the Pair Button
Tap the Multi-function
button
Double-tap the
Multi-function button
Tap the volume up or
volume down button
Press and hold (2 secs)
the volume down button
Headset off
Pairing
Pairing Successfully
Standby
Answer/End Call
Redial/
Reject Call
Adjust Volume
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Canada Regulatory Information
This device complies with Innovation, Science, and Economic
Development Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :
l'appareil nedoit pas produire de brouillage, et
l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettrele fonctionnement.
The device is compliance with RF exposure guidelines, users can
obtain Canadian information on RF exposure and compliance.
Certification information
Common part：
This equipment complies with radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
U.S. FCC Part 15 Regulatory Information
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Le présent appareil est conforme DX[GLUHFWLYHVGH[SRVLWLRQ RF, les
utilisateurs peuvent DFTXpULUOHVLQIRUPDWLRQVFRUUHVSRQGDQWHVsur
l’exposition aux radiofréquences et la conformité
EU Regulatory Information
Support Frequency Bands and Power:
BT_BR+EDR < 7dBm
The simplified EU declaration of conformity referred to in Article
10(9) shall be provided as follows:
Hereby, [Grandstream Networks, Inc.] declares that the radio
equipment type [GUV3050] is in compliance with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available at the
following ,QWHUQHW address: www.grandstream.com
For Certification, Warranty and RMA information, please visit
www.grandstream.com
456
Grandstream Networks, Inc.
126 Brookline Ave, 3rd Floor
Boston, MA 02215 USA
Voice: (617) 566-9300
Fax: (617) 249-1987
www.
g
randstream.com
FCC ID: YZZGUV3050
Mute/unmute
microphone
How to use the Headset How to manage multiple calls
Headset on
FUNCTION ACTION
FUNCTION ACTION
LED STATUS
Slide the On switch *UHHQ/LJKWÀDVK
twice in succession
End current call and
answer incoming call
Tap the multi-function
button
Press and hold (2 secs)
the Multi-function button
Press and hold (2 secs)
the Multi-function button
Double-tap the
Multi-function button
Put current call on hold
and answer incoming call
Switch between held call
and active call
Reject incoming call,
when on a call
5HG/LJKWÀDVK
once in succession
%OXH/LJKWÀDVK
*UHHQ/LJKWÀDVKWZLFHDQGEOXH
OLJKWÀDVKRQFHLQVXFFHVVLRQ
%OXH/LJKWÀDVK
1 time per 8 secs
Slide the Off switch
Slide the Pair Button
Tap the Multi-function
button
Double-tap the
Multi-function button
Tap the volume up or
volume down button
Press and hold (2 secs)
the volume down button
Headset off
Pairing
Pairing Successfully
Standby
Answer/End Call
Redial/
Reject Call
Adjust Volume
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Canada Regulatory Information
This device complies with Innovation, Science, and Economic
Development Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :
l'appareil nedoit pas produire de brouillage, et
l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettrele fonctionnement.
The device is compliance with RF exposure guidelines, users can
obtain Canadian information on RF exposure and compliance.
Certification information
Common part：
This equipment complies with radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
U.S. FCC Part 15 Regulatory Information
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Le présent appareil est conforme DX[GLUHFWLYHVGH[SRVLWLRQ RF, les
utilisateurs peuvent DFTXpULUOHVLQIRUPDWLRQVFRUUHVSRQGDQWHVsur
l’exposition aux radiofréquences et la conformité
EU Regulatory Information
Support Frequency Bands and Power:
BT_BR+EDR < 7dBm
The simplified EU declaration of conformity referred to in Article
10(9) shall be provided as follows:
Hereby, [Grandstream Networks, Inc.] declares that the radio
equipment type [GUV3050] is in compliance with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available at the
following ,QWHUQHW address: www.grandstream.com
For Certification, Warranty and RMA information, please visit
www.grandstream.com
Other manuals for GUV3050
1
Table of contents
Other Grandstream Networks Headset manuals
Grandstream Networks
Grandstream Networks GUV3000 Instruction manual
Grandstream Networks
Grandstream Networks GUV3000 Instruction manual
Grandstream Networks
Grandstream Networks GUV3005 Instruction manual
Grandstream Networks
Grandstream Networks GUV3050 Instruction manual
Grandstream Networks
Grandstream Networks GUV3005 Instruction manual
Grandstream Networks
Grandstream Networks GUV3005 Instruction manual
Grandstream Networks
Grandstream Networks GUV3005 User manual
