Grandview GPCP-E6090 User manual

Cautious
Warnings For safety, the minimum of ceiling must be 20Kgweight
Caution Please do not incline the projector the extremely.
Please do not take apart the accessories of projector
ceiling mount.
Do not
take apart
Weight The maximum weight of installation bracket is 20Kg
(note: the installation bracket's maximum weight of GPCP-E90150 is 15kg)
Please read before using
Thank you for purchasing our products. Please read the instruction
manual carefully in order to ensure this projector lift is suitable for your
projection equipment.
Instruction Manual
Projector Wall Mount
Applicable Model
GPCP-E4060
GPCP-E6090
GPCP-E90150
figure 20
The front or back of
adjuster must be
parallel to the surface
of projector
figure 18 figure 19
figure 17
Installation of main bar
1.Firstly, please confirm how many installation holes the projector has?
3 or 4.
2.Install the required installation arms (4-3) to Installation bracke（4-
1） And then, installation arms(4-3) to the projector, and then connect
the installation arms (4-3) to the installation base (4-6) However,the
installation base needs to be the center of projector. Figure 17
3.Connect the installation arms to the projector conversely if the
distance of installation holes is less than 120mm. Connect the
installation arms (4-3) to the installation base (4-6) via sliding
installation button (4-5) as figure 18
4.Rotate the adjustable screw (4-4) for adjusting the height of instllation
arms (4-2) if the installation holes are not at the same level as figure 19.
5.The front or back of adjuster must be parallel to the surface of
projector as figure 20.
Scope of
adjustment: 10mm
Details of installation
Height and length adjustment
1.Loosen the positioning screws of low board (2-2), the height of GPCP
Main Bar Overview can be adjusted (the maximum height: 45mm) as
figure 11.
2.Loosen the positioning screws of main bar (1-4), the length of
subsidiary bar (1-3) can be adjusted (check about the data of scope for
installation) as figure 12.
3.Loosen the positioning screws of installation board (1-5), the height
of installation board (1-5) can be adjusted (the maximum height: 30mm)
as figure 13.
figure 11 figure 12 figure 13
Angle Adjustment
1.Horizontal adjustment: rotate the adjusting button (3-2) for horizontal
angle, figure 14
2.Vertical adjustment: rotate the adjusting button (3-3) for vertical
angle, figure 15
3.Horizontal rotation adjustment: loosen the rotation adjusting screw
(4-2), the installation base can be rotated by 360°; fasten the rotation
adjusting screw (4-2) after deciding the angle.figure 16
figure 14
figure 15
figure 16 vertical tilt:±15°
The angle of
horizontal tilt:±8°
The nagle of otation 360R : °
Grandview Crystal Screen
Canada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal
Screen Co., Ltd.
No.43,Guomao Road South, Hualong Town,
Panyu District, Guangzhou City, China
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.com
www.grandviewscreen.com.cn

GPCP-E is combined by GPCP and GPE
Firstly, collect the power wires to the main bar as figure 1.
Invaginate the low cap to the main bar as figure 2. Install the
low board to the main bar, and then fasten the screws
(accessories 5 ) as figure 3. Finally, install the front board to
installation board of main bar and install the adjuster to the
front board, and then fasten the screws (accessories 6) as
figure 4.
1
2
1-1 1-3 1-4 2-2
1-2 2-1
2-3
GPCP Main Bar Overview
1-1 Top Cap
1-2 Front Board
1-3 Subsidiary Bar
1-4 Main Bar
1-5 Installation Board
2-1 Low Cap
2-2 Low Board
2-3 Fixation
GPD Adjustment Overview
3-1 Adjuster
3-2 Horizontal Adjusting
Button
3-3 Vertical Adjusting
Button
4-1 Installation Bracket
4-2 Rotation Adjusting Screw
4-3 Installation Arm
4-4 Adjustable screw
4-5 Sliding Installation
Button
4-6 Installation Base
1-5
accessory 5
Parts
Scope for installation (Installation hole of projector):
Maximum scope for installation:390mm diameter
Minimum scope for installation:20mm diameter
Note: Connect the installation arms to the projector conversely for different installation
holes of projector.
Maximum diameter: 390mm
Scope
Minimum diameter: 20mm
Scope for installation (H is the distance between ceiling and projector)
The H of GPCP-E4060 is 420mm~600mm
The H of GPCP-E6090 is 600mm~900mm
The H of GPCP-E90150 is 900mm~1500mm
Scope
Steps of installation
figure 1 figure 2
figure 3 figure 4
Install the fixation on the wall (choose the screws according
to the materials of wall, Use the screw of accessory 7 for
concrete-wall, and use the screw of acessory 8 for wood-
wall) as figure 5.And then, install the Main Bar Overview to
the fixation and fasten the screws (accessory 5). Finally,
connect the GPE Adjusting Overview to the adjuster and
then fasten the screws (accessory 6 ) as figure 7.
Steps of installation
figure 5 figure 7
figure 6
Details of installation
Wires collection
Loosen out the positioning screws of main bar (1-4) as figure 8, and then
take apart subsidiary bar (1-3) from main bar (1-4). Put the wires into
the main bar (1-4) then insert the wires to the plastic groove of
subsidiary bar (1-3). And then, re-install the subsidiary bar (1-3) to main
bar (1-4) after collecting the wires as figure 9-10.
figure 8
figure 9
figure 10
①M3X8 Philips Screw (4pcs)
②M4X8 Philips Screw (4pcs)
③M5X8 Philips Screw (4pcs)
④M5X8 Philips Screw (4pcs)
⑤M6X12 Anti-Slip Screw (2pcs)
⑥M5X10 Philips Screw (7pcs)
⑦M6X25 Tapping Screw (4sets)
⑧ 6X50 Wood Screwn (4sets)
Accessories
3-1
3-2 3-3
4-1
4-5
4-2
4-4
4-3
4-6
H
GPCP-E