Grandview GPCM-G Series User manual

Instruction manual
Projector Ceiling Mount
Model: GPCM-G series
Please read before using
Thank you for purchasing our
products. Please read the
instruction manual carefully
to ensure this projector mount
is suitable for your projection
equipment.
Warning For safety, the minimum weight of ceiling must be 40KG;
Attention Please do not incline the projector extremely.
Please do not
take apart
Please do not take apart the accessories of projector
ceiling mount.
Cautious:
Use the screw for adjustment
A. Ceiling Installation with the main bar.
1. Make sure the ceiling can support a
40kg load.
2. Use the screw on the back to adjust
the extension bar to a desirable height,
put the cables into cable duct.
B. Fix the projector by connecting the
angle adjuster and the main bar.
1. Adjust the desirable angle.
2. Align the center position of the
projector and mount.
3. Connect the cables to the projector.
Remark: The 3 screws side on angle
adjuster is the front position.
C. Angle adjustment
1. Using the allen key to adjust the 2
screws for horizontal adjustment.
2. Using the allen key to adjust the
other 2 screws for vertical
adjustment.
Vertical adjustment:
UP 1 ; DOWN 8
3. Using the allen key to adjust the
length of the installation arms.
Adjustment screw
Use the screw
for adjustment
Horizontal
adjustment +/- 3
Horizontal rotation: +/- 4
#11- 3751 North Fraser Way, Marine Way
Business Centre, Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Grandview Crystal Screen Canada Ltd.

①
②
③
④
⑧
⑤⑥
⑦
5x35 screw(4pcs)
G100 100mm
45mm
15mm
100mm 165
265
410 730
435
235
200mm200mm
350mm 350mm
G200
G350
Diagram for applicable projector area
The installation arms support projector installation
within the diameter of 139mm – 455mm. The diameter
of the ceiling mounting holes is 153mm.
Diagram of the projector installation holes
Maximum diameter: 455mm
Minimum diameter: 139mm
Front View
Models Outer bar's
length(X) Inner bar's
length(Y) Min length(mm) Max length(mm)
Components assembly and accessories
GPCM-B is combined by GPC and GPM
Specifications
Models GPCM-G series
Max load 20kgs
Length 100/200/350
Unit(mm)
Components:
Omament cover
①Length adjustable screw ②
Main bar
③Sub-bar ④
Angle adjuster
⑤Fastener
⑥Installation arm ⑦Cables duct ⑧
Parts:
M3x20 Cross round screw(4pcs) M4x20 Cross round screw(4pcs)
Allen key(1pc) Rubber insert M5x20 Cross round screw(4pcs)
GPC
1.Assembly
The main bar and the sub-bar are fixed together from factory.
Install the whole unit onto the ceiling and tighten screws
securely. Then connect the angle adjuster and tighten it with
`desired projection direction.
2.Adjustment
Loosen the screw between the main bar and sub-bar. Adjust
the length of the bar by selecting the available screw holes
on the sub-bar. Tighten the screw once desired length is
confirmed.
GPM
1. Adjust the installation arms to match with the projector mounting holes. Ensure the
projector is in the center of the angle adjuster. Tighten securely.
2. Make sure the direction of theangle adjuster and the projection is the same.
3. The Installation arms are extendable to match with the projector mounting.
4. If the projector has only 3 holes mounting, simply take out 2 of the installation arms
and use only one arm to match with the available hole. Reserve the left installation
arm in proper place for future use.
figure 4 figure 5 figure 6
Three steps mounting:
A.Mount the whole GPC
unit on the ceiling and
tighten securely.
B.Connect the GPC and GPM
together after the projector is
properly mounted with GPM
as instructed.
C.Adjust your desired angle.
Optional
accessory Main bar