Grandview GPCN-D200 User manual

vertical tilt:±15°
The angle of
Instruction Manual
Projector Ceiling Mount
Applicable Model
GPCN-D200
GPCN-D3040
GPCN-D4060
Please read before using
Thank you for purchasing our
products. Please read the
instruction manual carefully
in order to ensure this
projector lift is suitable for
your projection equipment.
Cautious
Details of installation
Wires collection
If the volume of power wives are less than diameter of main bar (2-1)
that please put this power wires inside the main bar directly. But if the
volume is greater than the diameter, please take apart back ormanent
board (2-4 and 2-5) and positioning button (2-6) from main bar (2-
1)as figure 8. And then stay the power cord into the main bar (2-1),
figure 9 Finally, re-install the back ornament board (2-4) from the
other end, and then install positioning button (2-6) and back ornament
board (2-5), figure 10.
Height adjustment
Adjust the main bar (2-1) to required height after taking apart the front
ornament board (2-3) and loosening the front positioning screw. And
then, re-install the front positioning screw and the front ornament
board (2-3), figure 11. (The height of GPCN-D200 can not be
adjusted )
Angle adjustment
1.Loosen the positioning screws (front and back) for adjusting the
angle, and then rotate the screwdriver for fine turning to the required
angle as figure 12.
2.Loosen the positioning screws (left and right) for adjusting the angle,
and then rotate the screwdriver for fine turning to the required angle as
figure 13.
The nagle of
horizontal tilt:±5°
Installation of main bar
1.Firstly, please confirm how many installation holes the projector has?
3 or 4
2.If there are 3 holes, the installation arms (4-3) need to be taken apart
from Installation bracket firstly. Connect 3 installation arms(4-3) to the
projector, and then connect the installation arms (4-3) to the installation
base (4-6) However,the installation base needs to be the center of
projector. Figure 14.
3.Connect the installation arms to the projector conversely if the
distance of installation holes is less than 120mm. Connect the
installation arms (4-3) to the installation base (4-6) via sliding
installation button (4-5) as figure 15
4.Rotate the adjustable screw (4-4) for adjusting the height of instllation
arms (4-3) if the installation holes are not at the same level as figure 16.
5.The front or back of adjuster must be parallel to the surface of
projector as figure 17.
figure 14
figure 15 figure 16
figure 17
The front or back of
adjuster must be
parallel to the surface
of projector
Scope of
adjustment: 10mm
figure 8 figure 9 figure 10
figure 11
figure 12 figure 13
Warnings For safety, the minimum of ceiling must be 10KGweight
Caution Please do not incline the projector the extremely.
Please do not take apart the accessories of projector
ceiling mount.
Do not
take apart
Weight The maximum weight of installation bracket is 10Kg
Grandview Crystal Screen
Canada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal
Screen Co., Ltd.
No.43,Guomao Road South, Hualong Town,
Panyu District, Guangzhou City, China
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.com
www.grandviewscreen.com.cn

1-1
1-2
1-3
2-1
2-2
2-3
3-1
3-2
3-3
2-6
2-4
2-5
1
3
2
Install on
the flat
ceiling
GPCN-D200 GPCN-D3040 GPCN-D4060
Connect
main bar
and adjuster
(screws of
accessory ④)
Parts
GPCN-D is combined by GPCN and GPD
GPCN Main Bar Overview
1-1 Top Cap
1-2 Fixation
1-3 Sliding Adjusting Hole
2-1 Main Bar
2-2 Subsidiary Bar
2-3 Front Ornament Board
2-4 Back Ornament Board of Main Bar
2-5 Back Ornament Board of Subsidiary Bar
2-6 Moving Button
GPD Adjustment Overview
3-1 Adjuster
3-2 Hanging Button
3-3 Horizontal Adjusting
Hole
4-1 Installation Bracket
4-2 Vertical Adjusting Hole
4-3 Installation Arm
4-4 Adjustable Screw
4-5 Sliding Installation
Button
4-6 Installation Base
Accessories:
① M6x25 Tapping Screw (4sets)
② 6x50 Wood Screw (4pcs)
③ M5x8 Philips Screw (2pcs)
④ M5x16 Philips Screw (6pcs)
⑤ M5x8 Philips Screw (4pcs)
⑥ M4x8 Philips Screw (4pcs)
⑦ M3x8 Philips Screw (4pcs)
Scope for installation (Installation hole of projector):
Maximum scope for installation:360mm diameter
Minimum scope for installation:50mm diameter
Note: Connect the installation arms to the projector conversely for different installation
holes of projector.
Scope
Maximum diameter: 360mm Minimum diameter: 50mm
Scope for installation (H is the distance between ceiling and projector)
The H of GPCN-D200 is 200mm
The H of GPCN-D3040 is 300mm~400mm
The H of GPCN-D4060 is 400mm~600mm
Scope
Three steps of installation
Install the fixation on the ceiling (screws of accessory ① or ⑧ )as
figure 1, and the fixation also can be installed on the ceiling which
angle is less than 15°as figure 2. GPCN-D can be installed to the
concrete-roof with ceiling or without ceiling, such as figure 3.
Connect the GPCN Main Bar Overview to the fixation (screws of
accessory ④ ). Store the power wire, and then fasten the front and
back screws of main bar. Finally, install the ornament board of
main bar as figure 4 and figure 5.
Hang the installation bracket (projecter has been installed) to the
adjuster as figure 6. And then put in the screws (accessory ③).but
do not fasten.Pull the top cup to the main bar, and then invaginate
the spring as figure 7
Install on
the ceiling
which angle
is less than
15°
Three steps of installation
figure 1
figure 2
figure 3
figure 4
figure 5
15°
figure 6
figure 7
3-3
4-1
4-2
4-3
4-5
4-6 4-4
H
H
H