Grandview GPCM-E3540 User manual

Instruction Manual
GRANDVIEW REPRODUCING GENUINE COLORS
Projector ceiling mount
with high precision
adjustment
Applicable Model
GPCM-E3540
GPCM-E4560
Please read before using
Thank you for purchasing our
products. Please read the
instruction manual carefully
in order to ensure this
projector lift is suitable for
your projection equipment.
Cautious
Warnings For safety, the minimum of ceiling must be 20KGweight
Caution Please do not incline the projector extremely.
Please do not take apart the accessories of projector
ceiling mount.
Do not
take apart
Height Adjustment
Take apart the ornament cap of main bar (2-3) and loosen the front
positioning screws. Adjust the subsidiary bar (2-3) to reqiured
position, and then install the ornament cap of main bar (2-3) as figure
9 (the main bar of GPCM-D3540 is seperated by 8 segments, each
segment is 16mm; the main bar of GPCM-D4560 is seperated by 15
segments, each segment is 16mm)
figure 9
vertical tilt:±15°
The angle of
The nagle of
horizontal tilt:±8°
Rotation:360°
Angle Adjustment
1.Vertical adjustment: rotate the adjusting button (3-3) for vertical
angle, figure 10
2.Horizontal adjustment: rotate the adjusting button (3-2) for
horizontal angle, figure 11
3.Horizontal rotation adjustment: loosen the rotation adjusting screw
(3-4), the installation base can be rotated by 360°;fasten the rotation
adjusting screw (3-4) after deciding the angle,figure 12
figure 10 figure 11
figure 12
Installation of main bar
1.Firstly, please confirm how many installation holes the projector has?
3 or 4
2.If there are 3 holes, the installation arms (4-2) need to be taken apart
from Installation bracket firstly. Connect 3 installation arms(4-2) to the
projector, and then connect the installation arms (4-2) to the installation
base (4-5) However,the installation base needs to be the center of
projector. Figure 13.
3.Connect the installation arms to the projector conversely if the
distance of installation holes is less than 120mm. Connect the
installation arms (4-2) to the installation base (4-5) via sliding
installation button (4-4) as figure 14
4.Rotate the adjustable nuts (4-3) for adjusting the height of instllation
arms (4-2) if the installation holes are not at the same level as figure 15
5.The front or back of adjuster must be parallel to the surface of
projector as figure 16
The front or back of
adjuster must be
parallel to the surface
of projector
figure 13
figure 14 figure 15
figure 16
Scope of
adjustment: 10mm
Details of installation
Grandview Crystal Screen
Canada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal
Screen Co., Ltd.
No.43,Guomao Road South, Hualong Town,
Panyu District, Guangzhou City, China
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.com
www.grandviewscreen.com.cn

Install the fixation on the ceiling (screws of accessory ① )
as figure 1. GPCM-E can be installed to the concrete-
roof with ceiling or without ceiling,such as figure 2 and
figure 3.
1
2
GPCM-E3540 GPCM-E4560
1-1
1-2
2-1
2-4
2-3
3-1
3-2
4-1
4-2
4-3
4-4
4-5
2-2
3-2
2-5
3-4
H
H
Connect the adjuster to GPCM Main Bar Overview, and
then fasten the screws (accessory③ ) as figure 5.
Afterward, slide the Adjustment Overview (projecter has
been installed) to adjuster, and the fasten the screws
(accessory ④) as figure 6.
Parts
GPCM-E is combined by GPCM and GPE
GPCM Main Bar Overview
1-1 Fixation
1-2 Top Cap
2-1 Main Bar
2-2 Subsidiary Bar
2-3 Ornament Board of Main Bar
2-4 Ornament Board of Subsidiary Bar
2-5 Ornament Cap of Main Bar
GPE Adjusting Overview
3-1 Adjuster
3-2 Horizontal Adjusting Button
3-3 Vertical Adjusting Button
3-4 Rotation Adjusting Screw
4-1 Installation Bracket
4-2 Installation Arm
4-3 Adjustable Nut
4-4 Sliding Installation
Button
4-5 Installation Base
Accessories:
① M6x25 Tapping Screw (3sets)
② M5x10 Philips Screw/
Washer/Spring Washer (4sets)
③ M4x8 Socket Cap Screw (6pcs)
④ M5x8 Philips Screw (6pcs)
⑤ M3x30 Philips Screw (4pcs)
⑥ M4x30 Philips Screw (4pcs)
⑦ M5x30 Philips Screw (4pcs)
Scope for installation (Installation hole of projector):
Maximum scope for installation:345mm diameter
Minimum scope for installation:45mm diameter
Note: Connect the installation arms to the projector conversely for different installation
holes of projector.
Scope
Maximum diameter: 345mm Minimum diameter: 45mm
Scope for installation (H is the distance between ceiling and projector)
The H of GPCM-D3540 is 350mm~400mm
The H of GPCM-D4560 is 450mm~600mm
Scope
Two steps of installation
Two steps of installation
figure 1
figure 2 figure 3
figure 5
figure 4
Details of installation
Wires collection
Take apart the ornament cap of main bar (2-5) after connecting the
GPCM Main Bar Overview to the fixation (1-1), then stay the power
cord into the storage gap. At last, re-install the ornament cap of main
bar (2-5) as figure 7、 8 and 9.
figure 6 figure 7 figure 8