Grantech SYS8F361VGGA Series User manual

Technical Manual
Of
Intel Haswell/Broadwell Series CPU
Based
3.5’’ SBC
SYS8F361VGGA
Revision: 2.0
Release date: June 23, 2015
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

ii
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

iii
ENVIRONMENTAL SAFETY INSTRUCTION...................................................................................iv
USER’S NOTICE.................................................................................................................................... v
MANUAL REVISION INFORMATION................................................................................................ v
ITEM CHECKLIST..................................................................................................................................v
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD.........................................................................................1
1-2 SPECIFICATION.................................................................................................................... 2
1-3 LAYOUT DIAGRAM...............................................................................................................4
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING................................................................................................................11
2-2 CONNECTORS AND HEADERS........................................................................................ 16
2-2-1 CONNECTORS........................................................................................................16
2-2-2 HEADERS................................................................................................................ 20
TABLE OF CONTENT

1
Chapter 1
Introduction of the Motherboard
1-1 Feature of Motherboard
n
Onboard
Intel
®
Haswell/Broadwell
series
SoC
Processor,
with
low
power
consumption never denies high performance
nSupport 2 * DDR3L 1333/1600 MHz SO-DIMM, up to 16GB
nSupport 1 * SATAIII device
nOnboard 1* full-size mSATA/ Mini-PCIE slot
nOnboard 1* half-size Mini-PCIE slot
nOnboard 2 * RJ-45 gigabit Ethernet LAN port
nIntegrated with 1 * 24-bit dual channel LVDS header
nSupport 2* HDMI output
nSupport USB 3.0 data transport demand
nSupport CPU Smart FAN
nCompliance with ErP standard
nSupport Watchdog function

2
1-2 Specification
Spec
Description
Design
l
3.5
”
SBC
;
PCB
size:
14.8x
10.2
cm
Embedded CPU l
Intel
®
Haswell/Boardwell
ULT
SoC
CPU
*CPU model varies from different IPC options. Please consult your dealer for
more
information
of
onboard
CPU.
Memory Slot
l2 * DDRIIIL SODIMM Slot for un-buffered DDRIIIL 1333/1600 MHz
SDRAM, expandable to 16GB
l
Dual-channel
function
supported
Expansion Slot l
1*
Full-size
Mini-PCIE/mSATA
slot
(MMPE)
l
1*
Half-size
Mini-PCIE
slot
(MPE)
Storage l1* SATAIII 6G/s Connector (SATA1)
*SATA1 port & M-SATA connector (MMPE) supports RAID0/1 function.
LAN Chip
lIntegrated with Intel I211AT PCI-E Gigabit PCI-E LAN chip & Intel
I218LM Gigabit LAN PHY chip
l
Support
Fast
Ethernet
LAN
function
of
providing
10/100/1000Mb
ps
Ethernet data transfer rate
Audio Chip lRealtek ALC662 HD Audio Codec integrated
lAudio driver and utility included
BIOS l
AMI
128
MB
Flash
ROM
Multi I/O
Rear Panel I/O:
l1* DC 9V~24V power-in connector
l2* USB 2.0 port
l
4*
USB
3
.0
port
l
2*
RJ-45
LAN
port
l
2*
HDMI
port
l
1* Audio Line out/Optical SPDIF out port
Internal I/O Connectors& Headers:
l1* 2-pin 9V~24V DC-in internal power connector

3
l
1*
SATAII
I
6
Gb/s
port
l1* SATA Power connector
l1* CPU FAN connector
l
1*
Front
panel
audio
header
l1* SPK_OUT header (for 3W / 8 OHM amplifier)
l
4*
Serial
port
header
(COM1
supports
RS422/RS485
function)
l
1*
9-pin
USB
2.0
header
(Expansible
to
2*
USB
2.0
ports)
l1* 4-pin USB 2.0 header (Expansible to 1* USB 2.0 ports)
l
1*
GPIO
header
l1* SMBUS header
l
1*
PS2KBMS
header
l
1*
Front
panel
header
l
JP8:
1*
LAN
LED
activity
header
l
1*
LVDS
inverter
l1* LVDS header
Note: This manual serves as a common manual for SYS8F361VGGAseries. except
that power connector adopts 2-pin internal power connector, not DC-IN power jack on
the back panel.
Their main differences are listed as below:
Model
Power
Connector
SYS8F361VGGA 9V~24V DC Power-in Connector (On the rear I/O)
Note: The pictures for illustration examples in this manual are mostly taken from the
layout diagram for SYS8F361VGGA series,unless otherwise stated. Please refer
to your actual product for specification reference.
1-3
Layout
Diagram

4
Rear IO Panel Diagram
For Power connector 2 Series Series:
*Notice: Please connect compatible power supply to the power connector. The voltage of power
connector
should
not
be
lower
than
9V
or
higher
than
24V,
otherwise
it
may
do
harm
to
the
board
&
other
devices!
For Power-in Connector 1 Series:
Internal Diagram-Front Side:
Line-Out Port/
Optical SPDIF Out Port
USB
3.0
Ports
LAN1
RJ-45
LAN
Port
HDMI1 Port
HDMI2 Port LAN2
RJ-45
LAN
Port
USB
2.0
Ports
*9V~24V DC
Power-in
Connector
Line-Out Port/
Optical SPDIF Out Port
USB
3.0
Ports
LAN1
RJ-45
LAN
Port
HDMI1 Port
HDMI2 Port LAN2
RJ-45
LAN
Port
USB
2.0
Ports

5
For Power Connector 1 Series:
JP8:
LANLED
Headers
SATAIII Port
CPUFAN
Header
Front
Panel
Header
DDR3L
SODIMM
Slots
Reset
Button
Power
Switch
Button
9V ~24V DC
Power-in Connector
HDMI Ports
SMBUS
Header
INVERTER
LVDS
Header
Line-Out Port/
Optical SPDIF-Out Port
LAN1
RJ-45 LAN Port
Serial Port Header
(COM4/3/2/1)
USB
2.0
Headers
Front Panel
Audio Header
SATA Power
Connector
PS2KBMS
Header
MPE:Half-size
Mini-PCIE Slot
USB
3.0
Ports
USB
3.0
Ports
LAN2
RJ-45 LAN Port
USB
2.0
Ports
MMPE: Full-size
Mini-PCIE/mSATA
Slot
GPIO Header
SPK_OUT
Header

6
Internal Diagram-Front Side:
For Power connector 2 Series:
*Note: In the case that user wish to install two different cards to MPE & MMPE slot, make sure that
there
is
no
interference
between
the
cards
installed.
JP8:
LANLED
Headers
SATAIII Port
CPUFAN
Header
Front
Panel
Header
DDR3L
SODIMM
Slots
Reset
Button
Power
Switch
Button
HDMI Ports
SMBUS
Header
INVERTER
LVDS Header
Line-Out Port/
Optical SPDIF-Out Port
LAN1
RJ-45 LAN Port
USB
2.0
Headers
Front Panel
Audio Header
PS2KBMS
Header
MPE:Half-size
Mini-PCIE Slot
USB
3.0
Ports
USB
3.0
Ports
LAN2
RJ-45 LAN Port
USB
2.0
Ports
MMPE: Full-size
Mini-PCIE/mSATA
Slot
GPIO Header
Serial Port Header
(COM4/3/2/1) SATA Power
Connector
SPK_OUT
Header
Internal
9V ~24V DC-in
Power Connector

7
Internal Diagram-Back Side:
*Note: CPU is the most important part of the board and very fragile to any possible harm. Make sure
that
there
is
no
damage
to
the
CPU
during
any
installation
procedures
!
*Intel CPU

8
Jumper Position:
JP1
JP7
JP2
JP4
JP5
JP6
JBAT
JP3
COPEN
AT-MODE

9
Jumper
Jumper
Name
Description
JP3 LVDS PVCC 5V/3.3V /12V Select 4-Pin Block
JP2 INVERTER VCC 5V/12V Select 3-Pin Block
JP
7
COM
4
Header
Pin9
F
unction
Select
4-P
in
Block
JP5 COM3 Header Pin9 Function Select 4-Pin Block
JP6 COM2 Header Pin9 Function Select 4-Pin Block
JP
4
COM
1
Header
Pin9
F
unction
Select
4-P
in
Block
JBAT CMOS RAM Clear Function Setting 2-Pin Block
COPEN Case Open Message Display Function 2-Pin Block
AT_MODE
AT
Mode
Function
Select
2
-Pin
Block
JP1 Security Measure Function Select 2-Pin Block
ConnectorsConnector Name
*DCIN1 Power connector 1 Series: 9V~24V
DC-in Power Jack Connector
Power connector 2 Series:
Internal
2-Pin
9V~24V
DC-in
Power
Connector
SATA1
SATAI
II
Port
Connector
PW
OUT
SATA
Power
out
Connector
CPUFAN CPUFAN Connector
U
SB1/USB3
USB
3.0
Port
Connector
X4
U
SB5
USB
2.0
Port
Connector
s
X2
LAN1/LAN2 RJ-45 LAN Port Connector X2
HDMI
DVI-I
Port
Connector
X2
LOUT
Audio
Line
Out
Connector
MMPE Full-size Mini-PCIE/MSATA Connector
MPE Half-size Mini-PCIE Connector

10
Headers
Header
Name
Description
FP_AUDIO Front Panel Audio Header 9-pin Block
SPK_CON Speaker Header 4-pin Block
COM
4/3/2/1
Serial
P
ort
Header
X4
9-pin
Block
USB4 USB 2.0 Header 9-pin Block
USB6 USB 2.0 Header 4-pin Block
FP Front Panel Header(PWR LED/
HDD LED/Power Button /Reset) 8-pin Block
GPIO
GPIO
Header
10-pin
Block
SMBUS
SMBUS
Header
5
-pin
Block
PS2KBMS PS2KBMS Header 6-pin Block
JP8
LAN
Activity
LED
Header
4-
pin
Block
LVDS
24-bit
LVDS
Header
3
0
-pin
Block
INVERTER LVDS Inverter Connector 8-pin Block

11
Chapter 2
Hardware Installation
2-1 Jumper Setting
JP3 (4-pin): LVDS PVCC 3.3V/5V/12V Function Select
JP3→LVDS
4-6 Closed:
LVDS VCC= 12V.
6 4 2
3-4 Closed: LVDS
VCC= 5V;
2-4 Closed: LVDS
VCC= 3.3V;
3
1
5
1 3
5
2 4
6
1 3
5
2 4 6
JP2 (3-pin): INVERTER VCC 5V/12V Select
2-3 Closed: Inverter VCC= 12V.
JP2→INVERTER
1-2 Closed: Inverter VCC= 5V;
1 3
1
3

12
JP7 (4-pin): COM4 Header Pin9 Function Select
JP7→COM4
4-6 Closed:
RI= 12V.
6 4 2
3-4 Closed:
RI= 5V;
2-4 Closed:
RI=RS232;
3
1
5
1
3
5
2 4
6
1 3
5
2 4
6
JP5 (4-pin): COM3 Header Pin9 Function Select
JP5→COM3
4-6 Closed:
RI= 12V.
6 4 2
3-4 Closed:
RI= 5V;
2-4 Closed:
RI=RS232;
3
1
5
1 3
5
2 4
6
1 3
5
2 4 6

13
JP6 (4-pin): COM2 Header Pin9 Function Select
JP6→COM2
4-6 Closed:
RI= 12V.
6 4 2
3-4 Closed:
RI= 5V;
2-4 Closed:
RI=RS232;
3
1
5
1
3
5
2 4
6
1 3
5
2 4
6
JP4 (4-pin): COM1 Header Pin9 Function Select
JP4→COM1
4-6 Closed:
RI= 12V.
6 4 2
3-4 Closed:
RI= 5V;
2-4 Closed:
RI=RS232;
3
1
5
1 3
5
2 4
6
1 3
5
2 4 6

14
JBAT (2-pin): Clear CMOS
CMOS Clear Setting
1-2 Closed：Clear CMOS
JBAT
1-2 Open: Normal；
1
COPEN (2-pin): Case Open Message Display Function Select
COPEN
1
Case open function
GND
Pin 1-2 Closed: When Case open function pin short to GND, the Case open function
was detected. When Used, needs to enter BIOS and enable ‘Case Open Detect’
function. In this case if your case is removed, next time when you restart your
computer, a message will be displayed on screen to inform you of this.

15
AT_MODE (2-pin): AT Mode Function Select
Pin 1-2 closed: AT_MODE function is enabled. In this case your computer will
automatically turns on after a sudden power failure when power supply resumes.
1-2 Closed: AT Mode Selected.
AT-MODE
1
2
1-2 Open: Normal;
1
2
JP1 (2-pin): Security Measure Function Select
1-2 Closed: Disable Security Measures
in the Flash Descriptor(Override).
JP7
1
1-2 Open:Enable Security Measures
in the Flash Descriptor(Default);
1

16
2-2 Connectors and Headers
2-2-1 Connectors
(1)
Rear
I/O
Connectors
Icon Name Function
(*Optional for Power
connector 2 Series
Series)
DC 9V~24V Power-in
Connector
For user to connect compatible power
adapter to provide power supply for the
system.
USB 2.0 Port To connect USB keyboard, mouse or other
devices compatible with USB specification.
USB 3.0 Port
To connect USB keyboard, mouse or other
devices compatible with USB specification.
USB 3.0 ports supports up to 5Gbps data
transfer rate.
RJ-45 LAN Port This connector is standard RJ-45 LAN jack
for Network connection.
HDMI Port To connect display device that support HDMI
specification.
Line-Out Port/
Optical SPDIF Out Port
USB
3.0
Ports
LAN1
RJ-45
LAN
Port
HDMI1 Port
HDMI2 Port LAN2
RJ-45
LAN
Port
USB
2.0
Ports
*9V~24V DC
Power-in
Connector
(*Optional)

17
Line-Out Connector
/Optical SPDIF-Out
Connector
For user to connect external speaker,
earphones, etc to transfer system audio
output.
This connector can function as optical
SPDIF-Out jack with compatible cables &
devices.
(2)
DCIN1(2-pin)
:
9V~24V
DC-
in
Internal
Power
C
onnector
Pin No. Definition
1 +9V~+24V
2 GND
Pin1
Warning: Find Pin-1 position before connecting power cable to this 2-pin power connector. WRONG
INSTALLATION
DIRECTION
WILL
DAMAGE
THE
BOARD!!