Green Creative NCPLATE4 User manual

www.greencreative.com / [email protected] - Tel / Fax: [phone] - / GREENCREATIVELED / GClightingLED / GREEN-CREATIVE
For model #:NCPLATE468
WARNING – Read all product labels and instructions before installing fixture.
WARNING
NCPLATE468 INCLUDES:
1 x L-bracket
8 x M4 Screws
TO COMPLETE INSTALLATION YOU WILL NEED:
Cutting Pliers
Philips PH2 screw driver
– Wear safety gloves and other appropriate safety equipment.
NEW CONSTRUCTION PLATE INSTALLATION GUIDE – WARNING
DOWNLIGHT COMPATIBILITY & CIRCULAR KNOCKOUT (KO) SIZING
Circular Knockout (KO) InstructionsNew Construction Plate Dimensions Compatible Products
THINFIT 4"
8.5DLNC4DIM/xxx
10NCDLR4DIM/9xx/EXT
10NCDLR4DIM/9xx/277V/EXT
INNOFIT 4"
14CDLA6/xxx/277V
SPECFIT 4"
AD4LExxxxxDIMxxxxAD4Rxx
SELECTFIT 4”
SLFT4/xxCCTx/DIMx Use KO for 4" fixtures
THINFIT 6"
11.6DLNC6DIM/xxx
12NCDLR6DIM/9xx/EXT
12NCDLR6DIM/9xx/277V/EXT
INNOFIT 6"
21CDLA6/xxx/277V
SPECFIT 6"
AD6LExxxxxDIMxxxxAD6Rxx
SELECTFIT 6"
SLFT6/xxCCTx/DIMx
THINFIT 8"
24.5NCDLR8DIM/9xx/EXT
24.5NCDLR8DIM/9xx/277V/EXT
INNOFIT 8"
27CDLA8/xxx/277V
SPECFIT 8"
AD8LExxxxxDIMxxxxAD8Rxx
SELECTFIT 8”
SLFT8/xxCCTx/DIMx
Use KO for 6" fixtures
Remove KO for 8" fixtures
011420
Ø4”
Ø6”
A: Ø4-5/16”
B: Ø8-1/16”
C: Ø6-5/16”
19-11/16”
12”
A B C
Ø8”

For model #:NCPLATE468
NEW CONSTRUCTION PLATE DRYWALL INSTALLATION
fig. 3 fig. 4
fig. 5
fig. 7
fig. 6
fig. 1 fig. 2
Install here for
4" or 8"
Install here for 6"
Install here for
4" or 8"
THINFIT EXT
SPECFIT
SPECFIT
Install here for 6"
fig. 8
fig. 9
1. If applicable, using cutting pliers (not provided), remove any KO
sections necessary to install the selected downlight. (fig. 1)
2. For new construction installations or when required by local building
code, attach the NCPLATEJB* J-box (sold separately) in the appropriate
location using the pre-drilled mounting holes and provided screws. (fig. 2)
3. If applicable, install Emergency Battery Pack* (sold separately) into
the mounting holes using the screws provided. (fig. 3)
4. Nail or screw the NCPLATE468 to the ceiling's studs/joists. Note
NCPLATE468 allows a maximum spacing of 24". Use the spacing
distance marks on the side of the plate to center the downlight as
desired. (fig. 4)
6. If applicable secure the downlight’s driver*.
Bend the driver box’s middle clip downward and slide it around one of the
accessible plate’s finger tabs to secure the driver. (fig 5)
Attached the L bracket (included) into the mounting holes (fig. 6), then
bend out one the screw hole tabs of the driver box. Slide the driver in the
tab of the preinstalled L bracket, through the squared sliding hole of the
driver box. Finally secure the driver box to the L bracket with a screw
through the bended screw hole tabs of the driver box and the predrilled
hole of the L bracket. (fig. 7)
7. Connect power per individual fixture instructions.
8. Follow individual installation instructions to complete the fixture
installation.(fig. 9 & 10)
*At the discretion of the installer, NCPLATEJB, Emergency Battery
Packs and driver boxes can be secured to the ceiling structure by
alternate methods to meet NEC and local building codes without the use
of the new construction plate.
. For THINFIT EXT:
For SPECFIT:
www.greencreative.com / [email protected] - Tel / Fax: [phone] - / GREENCREATIVELED / GClightingLED / GREEN-CREATIVE

A A A
A
A
B2 B2
D
B1
4” 8” 6”
B1
F1
E1 E1 C C E2 E2
F2
E4 E4 E3
C&D
E3
C
A
For model #:NCPLATE468
NEW CONSTRUCTION PLATE DRYWALL INSTALLATION
A= THINFIT EXT with finger tabs C= Emergency Battery PackB= THINFIT EXT with key holes
D= SPECFIT driver bracket E= NCPLATEJB
Finger tabs for THINFIT EXT installation using clip hook installation
Screw holes for THINFIT EXT using key slot holes installation
Screw holes for Emergency Battery Pack installation
Screw holes for SPECFIT driver Bracket installation
Screw holes for NCPLATEJB installation
Extra holes
www.greencreative.com / [email protected] - Tel / Fax: [phone] - / GREENCREATIVELED / GClightingLED / GREEN-CREATIVE