GREENS Gisele User manual

GISELE WALL BASIN MIXER WITH PLATE
(For Mains Pressure Installations Only)
INSTALLATION INSTRUCTIONS
# 40079 12/18
ATTENTION PLUMBER
To ensure the optimum performance and customer satisfaction please adhere to the following:
 Flush out all pipe work prior to installation
 Installation shall be in accordance with the AS/NZS3500 series of standards.
The maximum operating pressure within any building should not exceed 500kpa.
Pressure above 500kpa can cause damage from water hammer, reducing life of appliances,
taps and fittings and cause excessive noise in the plumbing system.
 Pressure over 500kPa will require a limiting valve.
 Inline filters must be installed on both hot and cold supplies.
TECHNICAL DATA
 Minimum Water pressure for satisfactory operation: 150kpa
 Maximum Water pressure: 500kPa
 Maximum hot water temperature: 70ºC
If the Water temperature exceeds 70ºC an approved Tempering Valve must be fitted.
 The flow rate of the sink and basin mixers has been rated under the NZ Water Efficiency
Labeling Scheme (WELS).
Please leave this form with the product once installed.
For full warranty terms and conditions, please see the warranty card enclosed with this product
or visit www.greenstapware.com/warranty-and-care/
BATCH # PRODUCT #
Distributed by: Greens Global Limited
PO Box 5055, Hamilton, 3200
22 The Boulevard, Te Rapa, Hamilton 3200
Phone: [phone], Fax: [phone]
Website: www.greenstapware.com
Email: [email protected]
Service Hotline: [phone]

INSTALLATION INSTRUCTIONS
Note: Valve mounting 45-65mm behind finished wall.
Spout can be installed on the left or right side of the mixer valve.
Cut out holes in finished wall: Valve 40-43mm Spout 22-25mm.
Installing Mixer Valve Body:
1. Position the mixer against a mounting board within the maximum and
minimum depth of 45-65mm and fix.
a. Ensure the “Hot” (H) inlet, enters from the left, when the outlet to the
shower is at the top.
b. Mug guard has minimum and maximum for finished wall.
i. Leave mud guard on valve body until final fit out.
c. Note: Finished wall cut out must be up to the mud guard.
i. Note: Maximum cut out of 40-43mm.
2. Connect water supply to the mixer and from the mixer to the shower outlet.
a. Do not pressure test with valve in the open position when the outlet is closed.
Installing Spout Mounting Elbow:
1. Install the brass 15mm mounting elbow for spout position and connect water supply
from mixer outlet to elbow.
a. Check alignment of valve body and spout mounting using the pitch plate.
i. Check is level with a spirit level. Sit the pitch plate in the groove of valve
body and sit over the thread on the adaptor.
Note: Do not sit pitch plate in the groove in mounting adaptor.
b. To water test, remove the spout mounting adaptor by unscrewing and cap
off using 15mm threaded plug.
Install Face Plate & Handle:
1. Remove the mud guard.
2. Remove the protective tape from the seal and slide the faceplate over the mixer
body and mounting for elbow and position against the wall lining.
a. Plate is reversible.
3. Sealant will be required behind faceplate on uneven surfaces for water seal.
4. Install the handle onto the cartridge lever and tighten the screw under
the handle with the 2.5mm Allen key supplied and fit button.
Installing Spout & Mounting Adaptor:
1. Install the mounting adaptor to the mounting elbow.
a. The adaptor can be cut back to the groove.
b. Using a 1/4” Allen key (Not supplied).
c. To finish wall line as shown on adaptor.
3. Install the adaptor fix nut and screw up tight against the mounting elbow.
4. Grease the O-rings on the adaptor and install spout and tighten grub screws.
a. Check: The grub screws are not projecting into the bore to ensure the
O-rings are not cut.