GreenWorks 40V 20'' Cordless Snow Thrower 2600200 User manual
2600200
SNF401 www.greenworkstools.com
www.greenworkstools.ca
1 DESCRIPTION
1.1 PURPOSE
This machine is used to remove and clear away snow from
pavements, gardens, driveways and other ground-level
surfaces.
1.2 OVERVIEW
1Handle bar
2Bail switch
3Chute control rod
4LED lights
5Carrying or lifting handle
6Wheel
7Impeller
8Scraper
9Discharge chute
10 Battery compartment
11 Chute deflector
12 Safety switch button
2 GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your battery-
operated (cordless) power tool.
2.1 TRAINING
• Do not allow children under the age of 14 to operate this
tool. Children who are 14 years of age or older must read
and understand the operating instructions and safety rules
in this manual and must be trained and supervised by a
parent.
• Read the operating and service instruction manual
carefully. Be thoroughly familiar with the controls and
the proper use of the power tool. Know how to stop the
unit and disengage the controls quickly.
• Never allow children to operate the power tool. Never
allow adults to operate the power tool without proper
instruction.
• Keep the area of operation clear of all persons,
particularly small children, and pets.
• Exercise caution to avoid slipping or falling, especially
when operating in reverse.
• Do not use on graveled surface unless the snow thrower is
adjusted for such a surface in accordance with the
operator’s manual.
• Dress Properly – Do not wear loose clothing or jewelry.
They can be caught in moving parts.
• Wear appropriate boots when operating the snow thrower.
• Operation of the snow thrower in the hand-held position
is unsafe, except in accordance with the special
instructions for such use provided in the operator’s
manual.
• Avoid Accidental Starting– Don't carry the snow thrower
with fingers on the switch while the battery is inserted.
Be sure the switch is off when inserting the battery pack.
2.2 PREPARATION
• Thoroughly inspect the area where the power tool is to be
used and remove all doormats, sleds, boards, wires, and
other foreign objects.
• Do not operate the power tool without wearing adequate
winter garments. Wear footwear, which will improve
footing on slippery surfaces.
• Adjust the housing height to clear gravel or crushed rock
surface.
• Never attempt to make any adjustments while the
machine is running (except where specifically
recommended by manufacturer).
• Always wear safety glasses or eye shields during
operation or while performing an adjustment or repair to
protect eyes from foreign objects that may be thrown
from the machine.
• Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to battery pack, picking up
or carrying the appliance. Carrying the appliance with
your finger on the switch or energizing appliance that
have the switch on invites accidents.
2
English
EN
㸦㸧
㸪
Save these instructions.
7 INSTALLATION
WARNING
Do not change or make accessories that are not
recommended by the manufacturer.
WARNING
Do not connect to power supply until you assemble all the
parts.
7.1 UNPACK THE MACHINE
WARNING
Make sure that you correctly assemble the machine before
use.
WARNING
• If the parts are damaged, do not use the machine.
• If you do not have all the parts, do not operate the
machine.
• If the parts are damaged or missing, speak to the service
center.
1. Open the package.
2. Read the documentation in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and package in compliance with local
regulations.
7.2 INSTALL THE MIDDLE HANDLE
1. Align the holes in the middle handle (15) and the lower
handle (16).
2. Put the bolts (14) through the middle handle (15) and the
lower handle (16).
3. Tighten the handle knob (13) onto the bolt (14).
4. Repeat for left/right side.
7.3 INSTALL THE UPPER HANDLE
1. Align the holes in the middle handle (15) and the upper
handle (33).
2. Put the bolts (14) through the holes.
3. Tighten the handle knobs (13) onto the bolts (14).
4. Do the same operation on the other side.
7.4 INSTALL THE CHUTE
DEFLECTOR
1. Align the tabs (20) on to the slots (17) on one side first.
2. Once you have engaged one tab on one slot push until
you hear a click. Repeat on other side.
3. Push the chute deflector (11).
4. Make sure that the tabs (20) engage the slots (17) on the
two sides.
5
English EN
5. Make sure that the posts (19) engage the holes (18) on the
two sides.
7.5 INSTALL THE CHUTE CONTROL
ROD
1. Align the holes (18) in the upper chute control rod (23)
and lower chute control rod (21).
2. Put the hitch pin (22) through the holes (18).
3. Align the arrows in the discharge chute and snow thrower
deck. Make sure the discharge chute faces forward.
4. Put the end of the chute control rod (3) straight through
the hole (18) in the bracket. Keep the grip handle down.
5. Push the chute control rod (3) into the hole (18) behind
the deck.
6. Turn the grip handle left and right to make sure that the
discharge chute moves in the same direction.
7.6 INSTALL THE BATTERY PACK
WARNING
• If the battery pack or charger is damaged, replace the
battery pack or the charger.
• Stop the machine and wait until the engine stops before
you install or remove the battery pack.
• Read, know, and follow the instructions in the battery
and charger manual.
1. Open the battery door (10).
2. Align the ribs on the battery pack (33) with the grooves in
the battery compartment.
3. Push the battery pack (33) into the battery compartment
until the battery pack (33) locks into place.
4. When you hear a click, the battery pack (33) is installed.
5. Close the battery door (10).
7.7 REMOVE THE BATTERY PACK
1. Open the battery door (10).
2. Push and hold the battery release button.
3. Remove the battery pack (33) from the machine.
8 OPERATION
WARNING
Wear eye protection during operation.
8.1 COLD WEATHER OPERATION
The safe battery operation temperature ranges from 1°F
(-17°C) to 113°F (45°C).
WARNING
Do not store or charge battery outside.
Battery must be charged and stored indoors prior to use of the
machine.
If the machine does not start below 1°F (-17°C),
• remove the battery pack from the machine,
• charge the battery pack for 10 minutes in warm area, or
when the charging light turns green.
• Install the battery pack again.
8.2 START THE MACHINE
1. While holding the safety switch button (12), pull the bail
lever (2) to start the machine.
WARNING
Keep bystanders a safe distance from the machine.
6
English
EN
10
33
WARNING
Examine the work area. Remove all stones, sticks, wire,
bones, and other debris that can ricochet because of the
rotating impeller.
8.3 STOP THE MACHINE
1. Release the bail lever (2) to stop the machine.
WARNING
Wait until the impeller fully stops before you start the
machine again. Do not quickly turn the machine off and on.
WARNING
Remove the battery after you complete the work.
8.4 ADJUST THE DISCHARGE CHUTE
You can adjust the discharge chute 180° to change the snow
direction.
1. Turn the grip handle (3) left to move the discharge chute
(9) to the left.
2. Turn the grip handle (3) right to move the discharge chute
(9) to the right.
8.5 ADJUST THE CHUTE DEFLECTOR
You can adjust the chute deflector up and down to change the
throwing distance of the snow.
WARNING
Release the bail switch before you adjust the chute
deflector.
WARNING
Do not push the deflector so far forward that a gap shows
between the deflector and the chute.
1. Push and hold the trigger on the chute deflector (11).
2. Move the chute deflector (11) up to increase the snow
distance.
3. Move the chute deflector (11) down to decrease the snow
distance.
8.6 LED HEADLIGHTS
Turning the headlights on㸸
1. Push and hold the safety switch button (12).
2. Pull the bail lever (2) in the direction of the handle bar to
turn the headlights (4) on.
Turning the headlights off㸸
3. Release the bail lever (2).
7
English EN
8.7 OPERATION TIPS
• If it is possible, clear the snow with the direction of the
wind.
• In strong winds, lower the chute deflector to direct the
snow to the ground.
• When you complete the work, let the machine operate for
a while to prevent ice formation in the discharge chute.
• If the snow is deeper than 8", decrease the speed and let
the machine work at its own rhythm.
• Do not use the scraper to remove compact snow and ice.
9 MAINTENANCE
WARNING
Disconnect the extension cord before maintenance.
CAUTION
Use only approved replacement parts.
CAUTION
Do not use strong solvents or detergents on the plastic
housing or components.
9.1 GENERAL MAINTENANCE
• Before each use, examine the machine for damaged,
missing, or loose parts such as screws, nuts, bolts and
caps.
• Tighten correctly all the fasteners and caps.
• Clean the remaining snow on the machine with a brush.
9.2 REPLACE THE SCRAPER
WARNING
Use only approved replacement scrapers.
WARNING
Wear heavy gloves or wind cloth around the blade when
you touch the blade.
1. Remove the screws(24) from each side plate.
2. Remove the mounting screws (25) and spacers and
discard the old scraper.
3. Install the new scraper.
4. Reinstall the mounting screws (25) and spacers and
tighten them.
9.3 REPLACE THE IMPELLER
WARNING
Use only approved replacement scrapers.
1. Remove the 5 screws (24) and side wear pad (26) that
secure the right side cover (31).
2. Remove the nut (27).
3. Remove the 5 screws (24) and side wear pad(26) that
secure the left side cover (31).
8
English
EN
4. Remove the belt (28).
5. Using a socket wrench, remove the large pulley (29).
6. Remove the screws (24) that secure the left side plate.
24
7. Pull the axle (30) and remove the old impeller, install the
new impeller.
30
8. Reinstall the nut (27) and right side cover.
27
9. Reinstall the left side plate (32), large pulley (29), belt
(28) and left side cover (31).
9.4 STORE THE MACHINE
• Clean the machine before storage.
• Make sure the motor is not hot when you store the
machine.
• Make sure that the machine does not have loose or
damaged parts. If it is necessary, do these steps/
instructions:
• Replace the damaged parts.
• Tighten the bolts.
• Speak to a person at an approved service center.
• Store the machine in a dry area.
• Make sure that children cannot come near the machine.
10 TROUBLESHOOTING
Problem Possible cause Solution
The handle is not
in position.
The bolts are not
engaged correctly.
Adjust the height
of the handle and
make sure that the
knobs and bolts
are aligned cor-
rectly.
9
English EN
24
31
27
28
29
32 26
Problem Possible cause Solution
The machine does
not start.
The battery is not
charged.
Charge the battery
by following the
procedures in the
battery and charg-
er manual.
The switch is de-
fective.
Have the switch
replaced by an au-
thorized service
center.
Battery is too cold. Remove battery
from snow throw-
er. Place battery on
charger and allow
to charge for 10
minutes or until
the changing light
turns green. Re-
move from charger
and install in snow
thrower for use.
Battery may re-
quire service or re-
placement.
Call toll free help-
line, at
1-888-909-6757 or
replace battery.
The engine is on,
but the impeller
does not turn.
The belt is dam-
aged.
Replace the belt.
A thin layer of
snow stays behind.
The scraper is
damaged.
Replace the scra-
per.
* If you cannot find the solution to these problems, call
1-888-909-6757.
11 TECHNICAL DATA
Voltage 40 V
No load speed 1900 RPM
Clearing width 20 in
Clearing depth 8 in
Impeller size 16 in
Weight (without battery
pack)
34.2 Ibs
Battery 29662 and other BAF series
Charger 29692 and other CAF series
12 LIMITED WARRANTY
YEAR
ANS
LIMITED WARRANTY
GARANTIE
LIMITÉE
3
Greenworks hereby warranties this product, to the original
purchaser with proof of purchase, for a period of three (3)
years against defects in materials, parts or workmanship.
Greenworks, at its own discretion will repair or replace any
and all parts found to be defective, through normal use, free
of charge to the customer. This warranty is valid only for
units which have been used for personal use that have not
been hired or rented for industrial/commercial use, and that
have been maintained in accordance with the instructions in
the owners’ manual supplied with the product from new.
ITEMS NOT COVERED BY WARRANTY:
1. Any part that has become inoperative due to misuse,
commercial use, abuse, neglect, accident, improper
maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in
accordance with the owner's manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade
sharpening;
5. Normal deterioration of the exterior finish due to use or
exposure.
HELPLINE:
Warranty service is available by calling our toll-free helpline,
at 1-888-909-6757.
TRANSPORTATION CHARGES:
Transportation charges for the movement of any power
equipment unit or attachment are the responsibility of the
purchaser. It is the purchaser’s responsibility to pay
transportation charges for any part submitted for replacement
under this warranty unless such return is requested in writing
by Greenworks.
CANADIAN ADDRESS:
Greenworks Tools Canada Inc.
1110 Stellar Drive Unit 102
Newmarket, ON, L3Y 7B7
10
English
EN
13 EXPLODED VIEW
No. Part No. Qty Description
1 R0200281-00 1 Impeller assembly
2 R0200283-00 1 Weather bar
3 R0200285-00 1 PCB board
4 R0200284-00 1 Cam Lock Assembly
5 R0200165-00 1 Wheel Assembly
6 R0200166-00 1 Control Rod Assembly
7 R0200173-00 1 Chute Deflector Assembly
8 R0200282-00 1 Scraper Kit
11
English EN
Other manuals for 40V 20'' Cordless Snow Thrower 2600200
1
Table of contents
Other GreenWorks Snow Blower manuals
GreenWorks
GreenWorks ELITE 2605302 User manual
GreenWorks
GreenWorks 2600502 User manual
GreenWorks
GreenWorks 2600007 User manual
GreenWorks
GreenWorks DHA103 User manual
GreenWorks
GreenWorks 2600700CA User manual
GreenWorks
GreenWorks 2601402 User manual
GreenWorks
GreenWorks 26022 User manual
GreenWorks
GreenWorks 2600802 User manual
GreenWorks
GreenWorks GW80VSNW200 User manual
GreenWorks
GreenWorks 26012 User manual
GreenWorks
GreenWorks 2600202 User manual
GreenWorks
GreenWorks 2600400 User manual
GreenWorks
GreenWorks SN60L02 User manual
GreenWorks
GreenWorks SNF401 User manual
GreenWorks
GreenWorks 26272 User manual
GreenWorks
GreenWorks 2606502 User manual
GreenWorks
GreenWorks SN-200-T User manual
GreenWorks
GreenWorks GWSN20130 User manual
GreenWorks
GreenWorks 2600202CT User manual
GreenWorks
GreenWorks SNA107 User manual
