Grill Zone SRGG41207 User manual

Consumer: Retain this manual for future reference.
Installer: Leave this manual with consumer.
PLEASE CONTACT 1-866-814-0585 FOR ASSISTANCE
DO NOT RETURN TO PLACE OF PURCHASE
OFFICE HOURS 9AM TO 5PM EST
TM
MODEL NO.: SRGG41207 / TV NO.: 143758
64,000 BTU GAS GRILL
USER MANUAL
FOR OUTDOOR USE ONLY

2
SAFETY INSTRUCTIONS
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from the appliance and immediately call your gas
supplier or your fire department.
WARNING
1. Do not store or use gasoline or other flammable liquids OR vapors in the vicinity
of this or any other appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or
any other appliance.

3
SECTION ONE
Safety Instructions………………………… 4
Placement of the Grill……………………...8
SECTION TWO
Exploded View…………………………...…
Part List and Hardware List…………..…...
Assembly Instructions…….………..……....
Gas cylinder Installation Instruction….…..
SECTION THREE
Gas Hook-Up……………………………….
Leak Testing………………………………...
Installer Final Check ………………………
Read this User Manual carefully and
completely before using your grill
to reduce the risk of fire, burn
hazard or other injury.
SECTION FOUR
Operating Instructions………………..…
Lighting Instructions……………………..
SECTION FIVE
Using the Side Burner……………...……
Care & Maintenance ………………….…
How to Replace Main Burner………...…
Trouble Shooting…………………………
SECTION SIX
Limited Warranty………………..………..
TABLE OF CONTENTS
9
10
11
20
25
26
28
29
30
31
32
21
24
25

4
WARNING
Do not try lighting this appliance without first
reading the “LIGHTING INSTRUCTIONS” section
of this manual.
DO NOT LEAVE THE GRILL UNATTENDED
WHILE COOKING.
SAFETY INSTRUCTIONS
RECOGNIZED SAFETY SYMBOLS, WORDS AND LABELS
LP gas cylinder must be fitted with Overfill Protection Device (OPD).
DO NOT USE ALUMINUM FOIL TO LINE THE
GRILL RACKS OR GRILL BOTTOM. This can
severely upset combustion airflow or trap excessive
heat in the control area.
INSECT WARNING!!! Spiders and insects can nest
in the burners of this and any other grill, and cause
the gas to flow improperly. This is a very dangerous
condition, which can cause a fire to occur behind
and beneath the valve panel, thereby damaging the
grill and making it unsafe to operate. Inspect the
grill twice a year.
GAS INSTALLATION CODES
The installation must conform with local codes or, in
the absence of local codes, with the national fuel gas
code, ANSIZ223.1/NFPA 54, natural gas and propane
installation code, CSA B149.1, or propane storage
and handling code, B149.2,or the Standard for
Recreational Vehicles, ANSI A 119.2/NFPA 1192, and
CSA Z240 RV Series, Recreational Vehicle Code,as
applicable.
WARNING:
a) DO NOT store a spare LP/gas cylinder under or near this appliance.
b) NEVER fill the cylinder beyond 80% full.
c) If the information in “a” and “b” is not followed exactly, a fire causing death or serious
injury may occur.

5
Keep a spray bottle of soap water near the gas supply
valve and check the connections before each use. See
leak testing section
Do not attempt to light the grill if odor of gas is present.
Call for customer service 1-866-814-0585
SAFETY INSTRUCTIONS
RECOGNIZED SAFETY SYMBOLS, WORDS AND LABELS
WARNING: Always keep your face and body away from the burner when lighting.
WARNING: IMPORTANT!
BEFORE LIGHTING…
Inspect the gas supply hose prior to turning the gas “ON”. If it is evident there is excessive abrasion or wear, or the hose is
cut, it must be replaced prior to the grill being put into operation. The replacement pressure regulator and hose assembly
shall be that specified by the manufacturer. Do not use the grill if the odor of gas is present. Only the pressure regulator and
hose assembly supplied with the unit should be used. Never substitute regulators for those supplied with the grill.
If a replacement is necessary, contact the customer service number below for proper replacement.
Attach the regulator onto the cylinder. Check the hose and regulator connections using a soap and water solution
before operating the grill.

6
TESTED IN ACCORDANCE WITH ANS
Z21.58-2007 / CSA 1.6- 2007, ANS Z1.58- 2008 /
CSA1.6a-2008 STANDARD FOR OUTDOOR
COOKING GAS APPLIANCES. THIS GRILL IS
FOR OUTDOOR USE ONLY.
Check your local building codes for the proper
method of installation. In the absence of local
codes, you must conform with either the National
Fuel Gas Code, ANSI Z223.1/NFPA 54, or
CAN/CSA-B149.1, Natural Gas and propane
Installation Code. Electrical Code, ANSI/NFPA 70.
When properly cared for, your grill will give safe,
reliable service for many years. However, extreme
care must be used since the grill produces intense
heat and that can increase accident potential. When
using this appliance basic safety practices must be
followed, including the following:
Do not repair or replace any part of the grill unless
specifically recommended in this manual. All other
service should be referred to a qualified technician.
This outdoor cooking gas appliance is not intended to
be installed in or boats.
DO NOT STORE ITEMS OF INTEREST TO
CHILDREN AROUND OR BELOW THE GRILL OR IN
THE CART. NEVER ALLOW CHILDREN TO CRAWL
INSIDE OF THE CART.
Never let clothing, pot holders or other flammable
materials come in contact with or too close to any
grate, burner or hot surface. Fabric may ignite and
result in personal injury.
For personal safety, wear proper apparel. Loose fitting
garments or sleeves should never be worn while
this appliance. Some synthetic fabrics are highly
flammable and should not be worn while cooking.
Only certain types of glass, heatproof glass
ceramic, earthenware, or other glazed utensils are
suitable for grill use. These types of materials
may break with sudden temperature changes.
Do not heat unopened food containers as a build-up
of pressure may cause the container to burst.
Never lean over an open grill.
The outdoor cooking gas appliance shall not be used
under overhead combustible construction.
CALIFORNIA PROPOSITION 65-WARNING
The burning of gas fuel generates some
byproducts, which are known by the State of
California to cause cancer or reproductive harm. To
minimize exposure to these substances, always
operate this unit according to the use and care
manual, ensuring you provide good ventilation
when cooking with gas.
SAFETY INSTRUCTIONS
SAFETY PRACTICES TO AVOID
PERSONAL INJURY
using

7
When using the grill, do not touch the grill rack,
burner grate or immediate surroundings as these
areas become extremely hot and could cause
burns. Use only dry potholders. Moist or damp
potholders on hot surfaces may cause burns from
steam. Do not use a towel or bulky cloth in place of
potholders. Do not let potholders touch hot portions
of the grill rack.
Grease is flammable. Let hot grease cool before
attempting to handle it. Avoid letting excess grease
deposits collect in the grease slide panel bottom at
the bottom of the grill’s firebox. Clean this area
often.
For proper lighting and performance of the burners
keep the burner ports clean. It is necessary to clean
them periodically for optimum performance. The
burners will only operate in one position and must
be mounted correctly for safe operation.
Clean the grill with caution. Avoid steam burns; do
not use a wet sponge or cloth to clean the grill while
it is hot. Some cleaners produce noxious fumes or
can ignite if applied to a hot surface.
Be sure all grill controls are turned off and the grill is
cool before using any type of aerosol cleaner on or
around the grill. The chemical that produces the
spraying action could, in the presence of heat, ignite
or cause metal parts to corrode.
Do not use the grill for cooking excessively fatty
meats or products, which promote flare-ups. Do not
operate the grill under construction.
Use only in well ventilated areas. Do not use in
buildings, garages, sheds, breezeways or other such
enclosed areas. THIS UNIT IS FOR OUTDOOR USE
ONLY.
Keeps the area surrounding the grill free from
combustible materials, trash, or combustible fluids and
vapors such as gasoline or charcoal lighter fluid. Do not
obstruct the flow of combustion and ventilation air. If the
unit is stored indoors ensure that it is cool. If propane is
used, the cylinder must be unhooked and the propane
cylinder stored outside in a well-ventilated area, out of
the reach of children.
DO NOT USE BRIQUETTES OF ANY KIND IN THE
GRILL.
The grill is designed for optimum performance without
the use of briquettes. Do not place briquettes on the
fame tamers as this will block off the area for the grill
burners to vent. Adding briquettes can damage ignition
components and knobs, and void the warranty.
Keep the back of the cart free and clear from debris.
Keep any electrical supply cord, or the rotisserie motor
cord away from the heated areas of the grill.
Never use the grill in extremely windy conditions. If
located in a consistently windy area (oceanfront,
mountaintop, etc.) a windbreak will be required (see
below) . Always adhere to the specified clearance.
NEVER USE A DENTED OR RUSTY PROPANE
CYLINDER.
SAFETY INSTRUCTIONS

8
MINIMUM CLEARANCE:
2’ Clearance from both sides of combustible
material, and 3’ Clearance from the back.
LOCATION
When determining a suitable location take into
account concerns such as exposure to wind,
proximity to traffic paths and keeping any gas supply
lines as short as possible. Locate the grill only in a
well-ventilated area. Never locate the grill in a
building, garage, breezeway, shed or other such
enclosed areas. During heavy use, the grill will
produce a lot of smoke. Lock the wheels after the grill
is placed in a suitable position.
PLACEMENT OF THE GRILL
DO NOT RETURN TO RETAILER
ATTENTION
1-866-814-0585
REMOVE ALL PARTS FROM THE CARTON; IDENTIFY PARTS AND HARDWARE TO
BE SURE ALL PARTS ARE INCLUDED. ASSEMBLY REQUIRED.
IDENTIFY MISSING OR DAMAGED PARTS, PLEASE CALL CUSTOMER SERVICE
! !

9
EXPLODED VIEW
1
2
3
4
5
6
7
8
910
11
12
13
14
15
16 17 18 19 20
21
22
23
24
25
26
27
31
29
32
37
30
28
36
34
33 35

10
PART LIST
HARDWARE LIST
19. Wheel
20. Axle 1pc
21.
22.
Front right pole 1pc
Rear right pole 1pc
1pc
1pc
23. Right transom
Right side shelf
1pc
24.
Right side burner bowl
1pc
25.
Ignition pin
1pc
26.
27. Right side burner
1pc
28. Right side burner rack
1pc
29. Right burner lid
1pc
30. Grill body
1pc
31. Side burner valve
1pc
32. Regulator&gas hose
1pc
33.
Grease cup
1pc
1pc
34.
35. Bottom panel
36. Cylinder fixing hook
37. Connection bar
Grease cup hanger
2pcs
1pc
1pc
1. Lid
2. Warming rack
3. Cooking grid
4. Flame tamer
5. Main burner
6. Grease tray
7. Left side shelf
8. Side shelf handle bezel
9. Side shelf handle
10. Towel hook
11. Control knob bezel
12. Control knob
13. Left transom
14. Rear left pole
15. Front left pole
16. Condiment shelf
17. Lower front panel
18. Wheel cap
1pc
1pc
2pcs
5pcs
5pcs
1pc
1pc
2pcs
1pc
4pcs
6pcs
6pcs
1pc
1pc
1pc
1pc
1pc
2pcs
M5 x 12 wing bolts 15pcs
M10 nuts 2pcs D10 washers 2pcs
D5 washers 4pcs
PP washer 1pc
R-pins 4pcs
M6 x 12 wing bolts 2pcs M5 x 12 bolts 8pcs

11
ASSEMBLY INSTRUCTIONS
STEP 1
Insert the axle (20) through the front right pole (21) and rear right pole (22), secure them with 2pcs
R-pins.
STEP 2
Attach 1pc pp washer, 2pcs D10 washers, 2pcs M10 nuts, 2pcs R-pins, 2pcs wheels (19) and 2pcs
wheel caps (18) to the axle (20) and secure them in turn as shown.
21
20
R-pin 2pcs
22
PP washer 1pc
D10 washers 2pcs
M10 nuts 2pcs
18
19
20
R-pin 2pcs

12
ASSEMBLY INSTRUCTIONS
STEP 4
Insert the 4pcs pre-installed bolts on left transom (13) into the 4 key holes on front left pole (15)
and rear left pole (14), secure them with 4pcs M5 x 12 wing bolts.
STEP 3
23
21
13
15
14
22
M5 X 12 wing bolt 4pcs
M5 X 12 Wing bolts 4pcs
Pre-installed
bolts 4 pcs
Pre-installed
bolts 4 pcs
Insert the 4pcs pre-installed bolts on right transom (23) into the four key holes on front right pole (21)
and rear right pole (22), secure them with 4pcs M5 x 12 wing bolts.

13
ASSEMBLY INSTRUCTIONS
STEP 5
STEP 6
21
17
15
35
M5 X 12 wing
bolt 3pcs
Insert the 4pcs pre-installed bolts on lower front panel (17) into the 4 key holes on front left pole (15)
and front right pole (21), press down to position.
1) Insert the 2pcs pre-installed bolts on bottom panel (35) into the 2 key holes on front left pole (15)
and front right pole (21);
2) Insert the 2pcs pre-installed bolts on bottom panel (35) into the 2 key holes on rear left pole (14)
and rear right pole (22);
3) Press down the bottom panel (35) to position and secure it to the rear left pole (14) and rear right
pole (22) with 3pcs M5x12 bolts.
21
14
15
22

14
ASSEMBLY INSTRUCTIONS
STEP 7
STEP 8
36
35
Insert the 2pcs pre-installed bolts on condiment shelf (16) into the holes on top of front left pole (15)
and front right pole (21), slide down and then place another 2pcs pre-installed bolts on condiment
shelf (16) to position as shown.
Insert the cylinder fixing hook (36) into 2 holes on bottom panel (35).
16 15 21
16
M5 x 12 bolts 2pcs
Then fix condiment shelf (#16) onto front left & right poles (#15 & #21) with 2pcs M5 x 12 bolts as
illustrated.

51
ASSEMBLY INSTRUCTIONS
STEP 9
Insert the ends of connection bar (37) into the holes on front left pole (15) and bottom panel (35)
STEP 10
Place the grill body (30) onto the assembled cart, secure it with 4pcs D5 washersand 4pcs
M5x12 wing bolts.
M5 X 12 wing bolts 4pcs
D5 washers 4pcs
35
37
15
30
as illustrated.

16
ASSEMBLY INSTRUCTIONS
Step 11
2) Install left side shelf (7) onto grill body (30) with 4pcs M5 x 16 bolts which are pre-installed on the
grill body, not to tighten them instantly. Locking front panel of left side shelf (7) to main control panel
with 2pcs M5 x 12 bolts (CC). Finally, tighten all the 6pcs bolts.
3) Repeat the same procedure to install right side shelf (24).
7
24 CC
M5 x 16 bolts 4pcs
(pre-installed)
30
7
BB
9
10
8
1) Hang 4pcs towel hooks (10) on the side shelf handle (9). Install side shelf handle (9) and 2pcs side
shelf handle bezels (8) to left side shelf (7) with 2pcs M6 x 12 bolts.

17
ASSEMBLY INSTRUCTIONS
STEP 12
Insert the metal hose into the main burner gas pipe and screw to tighten with two wrenches.
WARNING:
KEEP FLEXING OF THE METAL HOSE MINIMAL TO PREVENT FUTURE LEAKS.
PERFORMA LEAK TEST WITH A SOAPY SOLUTION BEFORE USING.
PLEASE REFER TO “LEAK TESTING” SECTION OF THE USER MANUAL.
Caution: pay attention to
metal hose positioning Main burner gas pipe

18
ASSEMBLY INSTRUCTIONS
STEP 13
26
Flame orifice
Ignition pin
Ignition wire
26 25
27
Insert the end of ignition wire to the ignition pin (26) on the right side burner bowl (25).
Note: manually adjust the gap between the ignition pin and the flame orifice around 3~5mm
(0.1 - 0.2inch) to ensure proper ignition.

19
ASSEMBLY INSTRUCTIONS
STEP 14
34
33
30
6
M5x12 bolts 2pcs
2
3
4
30
Fix grease tray (6) onto the grill body (30) with 2pcs M5 x 12 bolts; install grease cup (34) into
grease cup hanger (33) and then hang them onto the bottom of grease tray.
STEP 15
Place 4pcs flame tamers (4), 2pcs cooking grates (3) and 1pcs warming rack (2) into the grill body
(30) in turn.

20
GAS CYLINDER INSTALLATION INSTRUCTIONS
STEP 1
STEP 2
1) Check to ensure that the valve of gas cylinder is securely turned off prior to making the connection. If not, turn
the valve clockwise to turn it off.
2) Connect the hose and regulator assembly to the gas cylinder. Turn the requlator clockwise to make sure it’s
securely tightened.
Shut off gas supply by rotating valve of gas cylinder clockwise.
Gas cylinder
Fix regulator
by rotating it
clockwise
Place gas cylinder (not included) into the hole at bottom panel (35).
Life the cylinder fixing hook (36) to secure the gas cylinder.
35
36
Gas cylinder