Grinders Little Collins User manual

LITTLE COLLINS
INSTRUCTION
MANUAL
VISIT OUR ONLINE STORE: www.grinderscoffee.com.au
Grinders National Sales Centre Ph: 1300 476 377

21
WELCOME TO
Grinders Café Espresso.
We hope you enjoy your new
Little Collins coffee machine.
DESIGNED FOR THE
AUSTRALIAN LOVE OF COFFEE
CAPSULE EASILY
INSERTED AND
AUTOMATICALLY
EJECTED
CAPSULE BIN
CAPACITY:
8 CAPSULES
ADJUSTABLE
CUP SHELF
INDEX
INTRODUCTION:
• Welcome 1
• Safety Warnings 3
• Symbols Guide 4
INSTRUCTIONS:
• Machine Components 5
• Correct Use of Buttons/Indicator Lights 5
• First Time Use 6
• Dispensing Coffee 8
• Dispensing Hot Water 9
• Turning on the Appliance - Daily Use 10
• Adjusting the Cup/Mug Height 10
• Programming the Quantity of Beverage in a Cup 11
• General Operating Indications 12
CLEANING AND MAINTENANCE:
• Daily Maintenance 14
• Descaling Instructions 15
MISCELLANEOUS:
• Saving Energy 17
• Restore Factory Settings 18
• Troubleshooting 19
• Technical Data 21
• Grinders National Sales Centre Contact 21
• Warranty Details 22

3 4
SAFETY WARNING
If you do not comply with the operating instructions and safety warnings in this Instruction Manual,
the machine may become dangerous to operate. Please ensure you keep this Instruction Manual in
a safe place. Carefully read the following instructions before use. This way you will avoid the risk of
personal injury and damage to the appliance.
This appliance is intended to be used in domestic environments.
Not suitable for Professional use.
Use Caffitaly System compatible capsules. Damage caused by using incorrect capsules
will void the guarantee.
Use of the appliance in any manner other than as directed within this manual could cause
harm to the operator and void the guarantee. The manufacturer will not be responsible for
injury or damage resulting from improper use of the appliance.
After removing the packaging, check that the appliance is not damaged. If damage is
detected, or upon the first sign of a defect (unusual noise or odours), or if any other
problem is detected inside the appliance, do not use it and contact the
Grinders National Sales Centre on 1300 476 377.
The packaging elements (plastic bags, etc.) must not be left within reach of children as
they are potential sources of danger.
Only use the appliance if the power cord is intact. If the cord is damaged it must be
replaced by the manufacturer or importer due to potential electrical safety risks.
Please contact the Grinders National Sales Centre on 1300 476 377.
Use and store the appliance indoors. Make sure the electrical elements, plug and cord are
dry. Never submerge the appliance in water. Protect the appliance from sprays and drips.
Water and electricity together constitute a risk of electrocution.
Do not leave the power cord near hot surfaces, sharp edges or other sharp objects.
Only connect the appliance to power outlets complying with the requirements of the law.
Make sure that the power supply voltage matches the rating shown on the data plate on
the bottom of the appliance.
Do not pull on the power cord to disconnect it. Remove the plug carefully to avoid damage
to the outlet.
Continued on next page
GUARANTEE
VOID
X
X
SAFETY WARNING - Continued
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
Never place your hands inside the Capsule Compartment. There is a risk of injury.
Do not open the Lever while the appliance is operating. If the Lever is raised during the
delivery of a product, the machine can emit jets of hot water. Risk of Burns!
Do not remove parts of the appliance, OR insert objects into the openings. This could
cause electric shocks! Any operation that is not described in this instruction manual
should only be performed by an Authorised Support Centre. Please contact the
Grinders National Sales Centre on 1300 476 377.
Install the appliance on a solid, stable, heat resistant surface with an incline no greater
than 2 degrees.
When the Indicator Light blinks ORANGE and the machine beeps, it is advisable to
perform the Descaling Cycle, as illustrated on Page 15. If you do not, the appliance
may be damaged.
Clean the appliance carefully and regularly with a soft cloth and a mild detergent, do not
use alkaline cleaning agents. If it is not cleaned, the build-up that forms may be hazardous
to your health. Unplug the appliance and allow it to cool before cleaning.
Unplug the machine if you do not expect to use the appliance for a long period of time
(leaving on vacation, etc.).
SYMBOLS GUIDE
CAUTION: This is the safety warning symbol. It is used to call your attention to possible
risks of personal injury. Abide by the safety messages provided in order to avoid possible
injury or death.
This is the symbol used to
highlight some actions that
will optimise the use of this
appliance.
Not Dishwasher
Safe
Maintenance Tips

65
MACHINE COMPONENTS
DIAGRAM 1: MACHINE COMPONENTS
CORRECT USE OF BUTTONS
DIAGRAM 2:
Lever for
opening and
closing Capsule
Compartment
Beverage
Dispenser
Used Capsule
Drawer
Dispensing
buttons and
Indicator light
Water Tank Lid
Capsule
Compartment
Water Tank
Power On/Off
switch
Electricity Cord
Grid
Drip Tray
Single Espresso Button -
30mL (Lit in WHITE).
Use for dispensing a single
espresso shot.
When in doubt follow the directions on the capsule
box regarding required button use.
Double Espresso Button - 60mL (Lit in WHITE).
Use for dispensing a double espresso coffee for a
stronger beverage. Also suitable for Hot Chocolate
and similar beverages.
Hot Water Button - 120mL (Lit in BLUE).
Do not use the Hot Water Button for
espresso coffee or any other beverages.
Inappropriate use of this button may damage the
machine and void your warranty.
Plug your machine in
and switch it ON using
the On/Off Switch.
Open the Water
Tank Cover & fill
the Water Tank
with fresh water
to the Max. Line
indicated.
1. 2.
Place a cup or
mug (at least
250mL) under the
Dispensing Spout.
Press the Hot Water
button. Water will
cycle through the
system (approx. 30
sec.) When done, the
RED Indicator Light
will switch off.
Along with the button
lights, the Indicator
Light will blink.
Check there
is no capsule
in the Capsule
Compartment.
Close the Lever.
6.
Continued on next page
Note: If the RED
Indicator Light
continues to blink
and no water has
been extracted,
repeat Step 6.
After Step 6.
has successfully
completed, all the
button lights will
continue to blink
while your machine
warms up. (Approx.
1 min.)
7.
3. 4.
5.
FIRST TIME USE
USE CAFFITALY SYSTEM
COMPATIBLE CAPSULES
We recommend following these steps after not having used the machine for
a long period of time.
ON
WATER

87
FIRST TIME USE - Continued
When all the button
lights remain steadily
lit, rinse by pressing
the Hot Water button.
Press again to repeat
the rinse cycle.
Open the Water
Tank Cover & fill
the Water Tank
with fresh water
to the Max. Line
indicated. Your
machine is now
ready to use.
10.8.
9.
WATER
Once you have completed
the Rinse Cycle. Remove
the Drip Tray and Used
Capsule Drawer, empty
any residual water,
rinse with fresh water
and replace onto your
machine.
The selected button
will blink and
the machine will
stop dispensing
on reaching the
programmed
amount.
Raise the Lever
to eject the used
capsule into the
Used Capsule
Drawer and then
lower the Lever.
WARNING!
Do not use the Hot
Water button (lit in
BLUE) for dispensing
coffee. Doing so will
damage the machine
and void your
warranty.
TIP: To ensure
optimum product
delivery between
uses, eject the used
capsule from your
machine & rinse by
pressing the Double
Espresso button.
Insert the capsule,
pressing it gently
into place.
Close the Lever
fully.
Raise the Lever to
open the Capsule
Compartment.
Switch the machine
ON using the On/Off
Switch. Wait for your
machine to warm up.
Place a cup or
mug under the
Dispensing Spout.
Select the
Single or Double
Espresso button
depending on the
desired coffee.
DISPENSING COFFEE
3.
7.
4.
5.
8. i.
6.
1. 2.
ON

9 10
i.
DISPENSING HOT WATER
All the button
lights will flash
simultaneously for
approx. 60 sec. until
your machine has
warmed up.
Switch the machine
ON using the On/
Off Switch. Top up
the Water Tank if
required.
When all the
buttons are steadily
lit the machine is
ready for use.
Press and release the
Hot Water button. The
Hot Water button will
flash. Dispensing stops
when the programmed
amount is reached or
press the button to stop
dispensing in advance.
WARNING!
Only use the Hot Water
button (lit in BLUE) for
dispensing hot water.
Dispensing coffee using
this button will damage
your machine & void
your warranty.
2.
4.
1.
3
ON
Note: The quantity of beverage dispensed
can be programmed according to personal
taste and the size of the cups or mugs
used. Please refer to ‘Programming the
Quantity of Beverage in a Cup’ on Page 11.
TURNING ON THE APPLIANCE
- DAILY USE
ADJUSTING THE CUP/MUG HEIGHT
Your machine can be adjusted for the use of mugs or espresso cups.
This raises the
height of the
cup towards the
Dispensing Spout.
For tall mugs,
the Drip Tray can
be detached and
removed.
When all the
button lights are
steadily lit, the
machine is ready
to use.
Plug your machine in
and switch it ON using
the On/Off button. All
the button lights will
flash simultaneously
for approx. 60 sec.
until your machine
has warmed up.
Open the Water
Tank Cover & fill
the Water Tank
with fresh water
to the Max. Line
indicated.
Your machine is
initially set for the
use of large cups
or mugs.
For best results
using espresso
cups, you can lift
and rotate the Grid
placed over the
Drip Tray.
3.
3.
2.
4.
1. 2.
1.
ON
WATER

1211
PROGRAMMING THE QUANTITY
OF BEVERAGE IN A CUP
Note: The quantity of coffee dispensed may be programmed, from a minimum of 30mL
to a maximum of 250mL.
Note: Recommended Programming/Factory Programming:
- 30mL: Single Espresso Shot
- 60mL: Double Espresso Shot
- 120mL: Hot Water Button
Note: Quantities are approximate and may vary slightly between capsules.
Switch the
machine ON using
the On/Off Switch.
Wait for your
machine to warm
up.
Close the Lever
fully.
Place a cup or
mug under the
Dispensing Spout.
Insert the capsule,
pressing it gently
into place.
Press and hold the
desired beverage
button.
On reaching the
desired amount
of beverage,
release the button.
Now the button
is programmed
to your desired
amount.
Raise the Lever to
open the Capsule
Compartment
to eject the used
capsule and lower
the Lever.
Raise the Lever to
open the Capsule
Compartment.
1.
5.
2.
6.
3.
7.
4.
8.
ON
WATER
When the Indicator
Light blinks ORANGE
and the machine
emits 3 beeps it’s
advisable to perform
the Descaling Cycle.
Refer to Page 15 for
Descaling Instructions.
The Water Tank is
empty when the
Indicator Light blinks
RED and the machine
emits 3 beeps,
followed by a single
intermittent beep.
When all the
button lights are
lit steadily, your
machine is ready
to use.
Press any one of
the buttons. Wait
for the machine
to complete the
Priming Cycle as it
fills up with water.
When all the
button lights blink
continuously, the
machine is warming
up.
GENERAL OPERATING INDICATIONS
DESCALING SIGNAL: HEATING:
WHEN THE WATER RUNS OUT DURING OPERATION:
1.
4.3.
Fill the Water
Tank with fresh
water.
2.

1413
If the Lever is
raised during
the delivery of
a beverage, the
machine can emit
jets of hot water.
Risk of burns!
The machine will
immediately stop
dispensing.
The Indicator Light
blinks RED and a
beep is emitted.
Press any of the
buttons to reset
the alarm. Your
machine is now
ready for use.
Close the Lever
fully.
GENERAL OPERATING INDICATIONS
- Continued
IF THE LEVER IS RAISED:
1.
2. 3.
DAILY MAINTENANCE
Remove the Front
Cover of the
Dispensing Spout
by opening the two
tabs at the sides.
Disassemble the
Dispenser Body
and rinse with
fresh water.
Remove the Water
Tank. Empty and
rinse with fresh
water.
Note: The Water
Tank is not
dishwasher safe.
Remove the Drip
Tray and Used
Capsule Drawer.
Pull out the Used
Capsule Drawer and
remove the Grid from
the Drip Tray.
Once all the
components
have been rinsed
with fresh water,
reassemble and
replace back onto
your machine.
3. 4.
5.
1. 2.
Use a soft damp cloth and a mild
detergent to clean the surfaces of the
appliance.
DANGER: Never submerge the appliance in water. Protect the machine from sprays and
drips. Water and electricity together constitute a risk of electrocution.
The plastic parts of the appliance are not
dishwasher safe.

15 16
DESCALING INSTRUCTIONS
Descaling Signal: When the Descaling Indicator Light blinks ORANGE and then remains
steadily lit. It is advisable to perform the Descaling Cycle within 48 hours or before next
use. Failure to descale your machine will be detrimental to the taste of the coffee and may
cause long term damage to your machine.
Note: Descaling refers to the removal of the natural mineral build up within the pipes
of the machine. If not removed this may result in a poor quality beverage and eventually
block the pipes. The machine features an advanced program that monitors how much
water is used to dispense beverages. This measurement provides the user with
indications as to when the machine needs to be descaled.
CAREFULLY read the directions for use on the package of the Descaling Agent. Avoid
contact with eyes, skin and machine surfaces. Do not switch the appliance off during
descaling, and do not lift the Lever. Someone must be present during the operation.
Don’t not use vinegar: it could damage your appliance.
Turn the machine
Off at the On/
Off Switch.
Ensure there
are no capsules
in the Capsule
Compartment and
lower the Lever.
Remove the Drip Tray
and Used Capsule
Drawer. Pull out the
Used Capsule Drawer,
and remove the Grid
from the Drip Tray.
Rinse all components
with fresh water.
Remove the Water
Tank. Empty and
rinse with fresh
water.
Note: The Water
Tank is not
Dishwasher safe.
Mix 125mL of
Descaling Agent
and 875mL of
water to make
1 litre of
Descaling
Solution.
Add the 1 litre
of Descaling
Solution to the
Water Tank.
Place a 1 litre container
under the Dispensing
Spout.
Note: Do not leave the
machine as you may have
to empty the container
as it cycles through the
Descaling Cycle.
1.
3.
2.
4.
5. 6.
OFF
DESCALING
SOLUTION
1Litre
Solution
875mL
Water
125mL
Descaler
mL
After approx.
5 min. pause after
the last dose, the
Double Espresso
button will blink
& beep indicating
the Descaling
Cycle has finished.
Remove and rinse
the Water Tank,
refill with fresh
water and replace
into the machine.
Remove and
empty the Drip
Tray and Used
Capsule Drawer.
Rinse with fresh
water, reassemble
and replace onto
machine.
When the Rinse Cycle
is complete, the
machine will beep
and all the button
lights will blink at
the same time. This
indicates the machine
is warming up.
Remove and rinse
the Water Tank,
refill with fresh
water and replace
onto the machine.
The appliance
will dispense the
Descaling Solution
at intervals: 5 doses
with approx. 4 min.
pause between
each. Total time
approx. 25 minutes.
Do not press any
buttons during this time.
The Indicator Light will
continue to blink.
Note: At the end of the
5th dose, the Water
Tank will be empty.
Do not refill.
Press and hold the
Single and Double
Espresso buttons
and at the same
time, turn ON the
machine.
Double Espresso
button will be lit and
the Indicator Light
will blink ORANGE
and RED. Press the
Double Espresso
button to start the
Descaling Cycle.
Press the Double
Espresso button to
start the Rinse Cycle.
Fresh water will run
through the machine to
rinse (approx. 500mL).
The Indicator Light will
blink ORANGE and RED
alternately.
Continued on next page
DESCALING INSTRUCTIONS - Continued
9.
7.
10.
8.
13. 14.
11.
15.
12.
16.
ON

17 18
To restore back to
normal operating
conditions, press
any button or lift
the Lever and the
machine will start
warming up.
When all the button
lights turn on and
remain steadily
lit, the machine is
ready to use.
The machine will
automatically
reduce power
consumption 10
minutes after last
use.
All the buttons
will slowly and
sequentially blink.
Remove and
empty the Drip
Tray and Used
Capsule Drawer.
Rinse with fresh
water, reassemble
and replace onto
machine.
When the button
lights turn on and
remain steadily
lit, the machine is
ready for use.
DESCALING INSTRUCTIONS - Continued
SAVING ENERGY
1.
3.
2.
4.
17. 18.
10Min
RESTORE FACTORY SETTINGS (RESET)
These instructions allow you to reset the machine back to its factory setting – helpful if you
experience an issue with the machine, or you have changed the pour levels for example, and cannot
change them back to their original settings.
If your machine hasn’t entered into Prime
mode, please repeat from Step 1. The
timing of Closing and Opening the Lever
is precise & may take a couple of attempts
before successful. If you have reset the
machine and the problem still continues,
please contact
Grinders National Sales
Centre. Details on the front cover.
Switch ON the
machine using
the On/Off Switch,
then after 1
second, close and
open the Lever
within 1 second.
The button lights
will flash and the
RED Indicator Light
will blink indicating
your machine now
needs to be Primed
as directed in ‘First
Time Use’.
The machine will
beep to signal
the reset has
been done, then
release the Single
Espresso button.
Ensure the Lever
is up and switch
the machine Off
using the On/Off
Switch.
Hold down the
Single Espresso
button for the
whole of Step 3 and
Step 4.
3.
5.
4.
i.
1. 2.
OFF
ON

19 20
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
First Use -There is a burning smell
when the machine first starts and a
beverage button is pressed.
• Machine heating up for the first
time.
• There may be a slight burning
smell coming from the machine
when first used. This is caused by the
water heating as it travels through
the pipes and will dissipate
Note: Steam may appear be
seen coming from the Capsule
Compartment, this is steam from the
hot water entering into the Capsule
Compartment and will dissipate.
Water residue within the machine on
opening.
• The system is quality checked prior
to dispatch. There may be residual
water left from testing
• The water residue will be
removed when you conduct the
‘First Time Use’ on Page 6.
RED Indicator Light
No beverage is brewed.
The Indicator light blinks RED and
beeps continuously.
• The Water Tank is empty • Fill the Water Tank with fresh
water. Press Single or Double
Espresso button. When the buttons
remain steadily lit, the appliance is
ready for use.
The Indicator Light is on and
steadily lit in RED. Water comes
out cold.
• Heating problems. • Turn off the machine, then turn it
back on after a few minutes.
Note: If the RED Indicator Light
remains steadily lit after turning the
machine off and on, perform a Factory
Reset as described on Page 18.
If the problem persists please contact
Grinders National Sales Centre on
1300 476 377
The RED Indicator light is lit
steadily and the buttons are
flashing.
• Priming. • Press the Double or Single
Espresso button to commence the
Prime process. Refer to Page 6,
‘First Time Use’.
ORANGE Indicator light - Descaling.
The Indicator Light is lit ORANGE.
• Machine requires Descaling. • Refer to ‘Descaling’ on Page 15 to
descale the machine.
Dispensing - When a coffee
Dispensing button is pressed, the
machine starts running, but stops
without dispensing coffee or after
dispensing only a small amount.
(Under 30mL).
• Pre-infusion
• Incorrect beverage quantity
programming.
• Pre-infusion involves a small
amount of hot water running through
the filters ensuring there is uniform
distribution of water over the entire
surface of coffee before the full
beverage is dispensed.
• Reprogram the quantity of beverage
corresponding to your selected button.
Refer to ‘Programming the Quantity of
Coffee in a Cup’ on Page 11.
Continued on next page
TROUBLESHOOTING - Continued
PROBLEM CAUSE SOLUTION
Coffee being dispensed very slowly
and is weak or poor quality.
• Incorrect coffee capsule being
used.
• Ensure you use the Caffitaly
System.
Coffee grinds appearing in the cup
or mug
• Incorrect coffee capsule being used.
• Not cycling water through the
machine after use.
• Ensure you are using Caffitaly
System compatible capsules only.
There will be a Caffitaly System logo
on the packaging.
• Cycle water through the machine
after each use by pressing the Double
Espresso button. This also assists in
stopping the coffee grinds building up
and blocking the system.
Other - The Lever cannot be
lowered.
The Used Capsule Drawer is full;
Capsule is stuck in the Capsule
Compartment.
Empty the Used Capsule Drawer.
Gently push down on the jammed
capsule with a new capsule.
Water is leaking from the Used
Capsule Drawer.
• Beverage has been dispensed
without using a capsule (excluding
Hot Water button).
• Not emptying the Used Capsule
Drawer after using the Cleaning/
Rinse Cycles.
• Used Capsule Drawer is full of
capsules.
• Regularly check the Used Capsule
Drawer for residual water and empty
if required.
• Check and empty the Used Capsule
Drawer after each Cleaning/Rinse
Cycle.
• Empty the Used Capsule Drawer.

21 22
The appliance has been manufactured using high quality materials that can be reused
or recycled. Dispose of the appliance in a suitable waste collection centre.
All materials and objects in contact with food products comply with the requirements of European
Regulation 1935/2004.
TECHNICAL DATA
Grinders National Sales Centre Contact
For more information on the machine operation, available capsules and other useful
hints and tips go to www.grinderscoffee.com.au or contact
Grinders National Sales Centre on 1300 476 377
Please dispose of the packaging and capsules thoughtfully.
Cardboard and capsules are recyclable. Before recycling your capsules,
ensure you contact your local Waste Collection Centre for capsule
recycling information.
Keep plastic bags, tags etc. out of reach of children and pets as they can
be a source of danger.
See the data plate on the
base of the machine.
Max. 15 bar
< 70dB A
Approx. 4 kg
1 Litre
Room temperature:
10°C - 40°C
8 Capsules
155 mm 270 mm 360 mm
370 mm
MACHINE – WARRANTY DETAILS
WARRANTY DETAILS
Dear Customer,
Thank you for buying this product. This Machine has been designed and produced using the best
technologies available.
1. Warranty Details:
(a) If your Grinders Café Espresso Machine develops a fault or defect during the warranty period, and subject to the terms below,
we will repair it or replace it.
(b) We offer this warranty on top of any guarantees imposed by the Australian Competition and Consumer Act 2010 and any other
applicable State or Territory legislation.
(c) The warranty applies for 12 months from the date of purchase.
(d) The warranty covers fault or defects in the product’s materials or manufacturing.
(e) The warranty does not cover:
(f) Misuse, or use other than in accordance with the product’s instructions;
(g) Negligence on your part;
(h) Normal wear and tear; or
(i) Faults or defects caused by third parties, including work done by unauthorised service or repair agents.
2. Making a Warranty Claim:
(a) To make a claim you should first contact the Grinders National Sales Centre by telephone on 1300 476 377 in Australia and we will be
able to provide you with the appropriate next steps for service or replacement of your Machine.
(b) Before contacting the Grinders National Sales Centre, please make sure you have carefully read the Instruction Manual supplied with
the Machine.
(c) After you have initiated the claim via the telephone, we may ask you to return the product to us, as per the address details in Point 4.
(d) You will need to provide your receipt as proof of purchase in order to make a claim under the warranty.
(e) Once you return the product and lodge a claim with us, we will assess the claim and let you know whether it is covered. The decision
whether to repair or replace a product is at our sole discretion unless there is a ‘major failure’ as defined under Australian Consumer Law.
(f) If it is covered, we will deliver the repaired or replaced product back to you. We will bear this cost.
(g) If it is not covered, we will deliver the product back to you and you will bear the transport cost.
3. General service and repair enquiries:
For general service and repair enquiries, please contact us on the telephone number below.
4. Contact details:
Grinders National Sales Centre
Ph: 1300 476 377
Imported by GRINDERS COFFEE HOUSE
50 SPARKS AVE, FAIRFIELD, VIC 3078
“GRINDERS” is a registered trade mark of Coca-Cola Amatil (Aust) Pty Ltd
5. Statutory Guarantees:
As well as the Grinders Café Espresso warranty, our goods come with guarantees that cannot be excluded under Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
6. Claim Details:
If you are making a claim under the warranty or the statutory guarantees, we will require the following information from you:
(a) Name;
(b) Address;
(c) Product purchased;
(d) Date of purchase;
(e) Machine Serial Number;
(f) Shop of purchase;
(g) Description of the problem.

VISIT OUR ONLINE STORE: www.grinderscoffee.com.au
Grinders National Sales Centre Ph: 1300 476 377
“GRINDERS” is a registered trade mark of Coca-Cola Amatil (Aust) Pty Ltd
DESIGNED TO EXTRACT
MORE FLAVOUR
EXPERTLY SOURCED
SPECIALTY ROASTED
PRE-INFUSION
8g FOR IDEAL COFFEE QUANTITY
BREWING CONSISTENCY